Resumen del contenido incluido en la página 1
Optically Isolated Single Port PCI Bus CE
RS-232/422/485 Serial Card
with Send Data Control
MODELS: 3PCIOSD1A 3PCIOSD1B
Documentation Number 3PCIOSD1x3903m (pn4649-r003)
This manual applies to models 3PCIOSD1A and 3PCIOSD1B. The “1” suffix
designates the number of ports on the card. The “A” models are equipped with
16550A UARTs with 16 byte transmit and receive buffers. The “B” models come with
16850 UARTs with 128 byte transmit and receive buffe
Resumen del contenido incluido en la página 2
TABLE OF CONTENTS CHAPTER 1: GENERAL INFORMATION.......................................1 INTRODUCTION .......................................................................................1 DESCRIPTION ..........................................................................................1 FEATURES ...............................................................................................1 SPECIFICATIONS .................................................................
Resumen del contenido incluido en la página 3
Ω Ω • RS-485 Signal Lines: TD(A), TD(B), RD(A), RD(B) and Signal Chapter 1: GENERAL INFORMATION Ground. (Data A & Data B lines when wired for 2-wire operation.) Introduction The B&B Electronics 3PCIOSD1x single port isolated serial interface Specifications card is designed for IBM compatibles with a PCI Bus. The PCI Bus: PCI bus version 2.1 design is Plug and Play compatible which allows the driver and Slot: Requires one PCI slot Operating System to select the IRQ and address
Resumen del contenido incluido en la página 4
Optical Isolation: Data Line Device: HCPL0600 Handshake Line Device: IL207 Max. Power Consumption: All ports loaded +5 V @ 325.0 mA or 1.625 W Accessories: Software: Driver Disk (3.5) for Windows 95/98/2000/NT 4.0 PCI/USB COM Port Utility Disk (3.5) Manual: Instruction Manual (this booklet) Documentation Number 3PCIOSD1x-3903m Manual Chapter 1 3 4 Chapter 1 Documentation Number 3PCIOSD1x-3903m Manual B&B Electronics Mfg Co – 707 Dayton Rd - PO Box 1040
Resumen del contenido incluido en la página 5
Chapter 2: SETUP Inspection Your 3PCIOSD1x serial card was tested for proper operation before shipment. It should be in perfect mechanical and electrical condition upon receipt. The card is normally pre-configured for RS-232 operation. The data clock speed is set by one jumper to x1 (normal) operation or to x4 operation. The operating mode of the card is set using 8 jumpers: 4 jumpers select RS-232 operation or RS-422/485 operation, one jumper sets RTS for RS-232 & RS-485 modes or Send
Resumen del contenido incluido en la página 6
Ω RS-232 Mode RS-422 Mode To configure the port for RS-232 mode, 5 jumpers must be To configure the port for RS-422 mode, 7 jumpers must be set/checked. The following settings will configure the port as RS- set/checked. The following settings configure the port as RS-422: 232: 1. Set the four jumpers of JP2 (A-D) to the "422/485" (right) 1. Set four jumpers of JP2 (A-D) to the "232" (left) position. position. 2. Set JP1 to the "RTS(232)" (right) position. 2. Set the top jumper "TX" of JP4
Resumen del contenido incluido en la página 7
Ω 5. The bottom jumper "Termination" of JP4 switches the 120 RS-422 Pinouts Termination resistor IN or OUT. Typically this resistor is not The RS-422 mode supports 2 channels (transmit and receive). used. In some cases, using high baud rates and very long cables, termination is needed. See B&B’s free RS-422/485 Name Description Direction DB25M Application Note, Termination section, page 16, for more Pin information (available on our websites). Shield Shield ------ 1 Figure 4 shows
Resumen del contenido incluido en la página 8
Ω Ω Ω Ω The receiver can also be enabled and disabled, a useful feature in two-wire communications to prevent the transmitted data from "echoing back" on its own receiver. The second jumper "RX" of JP4 4 X Baud Rate Option determines the receiver mode. When the jumpers are placed in the Baud rates higher than 115,200 are possible with the 3PCIOSD1x “485” position, the "echo" is turned off. This is achieved by disabling card in RS-232, 422, or 485 mode. Jumper JP3 controls the clock the r
Resumen del contenido incluido en la página 9
Chapter 3: WINDOWS INSTALLATION 5. After new hardware is detected, this screen will appear. (W95: Windows 95 and Windows 98 This screen is named Update Device Driver Wizard). Any prior installation using previous B&B serial drivers must be removed before installing the new drivers. (Refer to page 20.) Windows 98 screens are shown for this section. Windows 95 is a bit different with fewer steps and the screen names and text shown differs. Windows 95 differences are noted (W95:…) 1. C
Resumen del contenido incluido en la página 10
8. Select Floppy disk drives, Specify A:\ 11. Click Finish to begin the second part of the driver installation 9. Insert the driver disk, then Click Next. which installs the Com port driver for Port A. Windows will find “PCI Serial Adapter (3PCISD1)” and the driver inf file. (W95: Driver name not shown - skip to step 11) 12. Click Next. (W95: Skip to step 15) 10. Click Next. Documentation Number 3PCIOSD1x-3903m Manual Chapter 3 15 16 Chapter 3 Documentation Number 3PCIOSD1x-390
Resumen del contenido incluido en la página 11
13. Click Next to continue. Re-insert the driver disk if needed. 15. Click Finish to complete Com driver installation. The computer will finish Com driver installation for Port A. Windows will find the Communications Port and inf file. 16. Wait for the process to complete. To verify the installation, open My Computer, Control Panel, System (or Start, Setting, Control Panel, System). Then select the Device Manager Tab. continued next page 14. Click Next. (W95: Drive
Resumen del contenido incluido en la página 12
Removal of Card And Drivers If you need to remove the card from your system or remove the current driver before installing a possible future driver upgrade: 1. Open My Computer, Control Panel, System (or Start, Setting, Control Panel, System). 2. Select the Device Manager Tab (see figure on prior page). 3. Click B&B Electronics Serial Adapters, then Select the PCI Serial Adapter (3PCISD1) for the 3PCIOSD1x. 4. Click the Remove button. 5. Close the Windows, and Open My Computer, Drive
Resumen del contenido incluido en la página 13
Windows 2000 Professional This section covers device driver installation for Windows 2000 Professional. 1. Configure the port on the PCI card to the desired RS- 232/422/485 mode using the jumpers. 2. Install the card in the slot, start the computer as an Administrator or ask your system administrator to install the software. 3. Windows will detect the PCI card and start Found New Hardware Wizard to begin driver installation. When installation is complete, Windows will set the hardware a
Resumen del contenido incluido en la página 14
NOTE: The 3PCIOSD1 Optically Isolated PCI Serial Adapter card will be identified as the hardware compatible 3PCISD1 PCI Serial Adapter. Both cards use the same drivers and are functionally the same to the Operating System. 9. Open My Computer, Control Panel, System, then select the Hardware tab on System Properties. 10. Select Device Manager, then view the device list. Under B&B Electronics Serial Adapters, the PCI card is installed. Under Ports, COM3 was assigned to port A in the card.
Resumen del contenido incluido en la página 15
Windows NT 4.0 Removal of Card & Drivers 1. Configure the port on the PCI card to the desired RS- 232/422/485 mode using the jumpers. If you need to remove the card from your system or remove the current driver before installing a possible future driver upgrade: 2. Install the card in the slot, start the computer, and log on to Windows NT 4.0 as an Administrator or ask your system 1. Click on 3PCISD1 Port A under Ports (COM & LPT) and select administrator to install the software. Unin
Resumen del contenido incluido en la página 16
6. Insert the driver disk into drive A: 7. Enter A:\WinNT40\Setup.exe in the Command line for installation program window. (as above). 8. Click Finish to start the Setup program. 5. Click the Install button, then click Next. 9. Click Next. Follow the instructions until completed. continued next page 10. This driver does not require re-booting to complete installation. 11. Open the Control Panel, select Ports. Documentation Number 3PCIOSD1x-3903m Manual Chapter 3
Resumen del contenido incluido en la página 17
You can check details of the serial card setup using Windows NT Diagnostics, found under Administrative Tools. This can show the Resources used such as addresses and IRQ. Windows Diagnostics will not allow changing anything. 12. Verify 1 new COM Port. (shown here as COM5) If you have 1 new COM port, the installation is complete. Select the port, select Settings, Advanced. You should obtain the message, "There are no user configurable Advanced I/O parameters for this COM port." Check t
Resumen del contenido incluido en la página 18
The screen below shows the address range for the serial port on the B&B Electronics 1-port Serial Card. Removal of Card and Driver If you need to remove the card from your system or remove the current driver before installing a possible future driver upgrade: 1. Open the Windows NT subdirectory. 2. Open System32. 3. Open Drivers. 4. Find the "Bbserial.Sys" file and delete it. 5. Shut down the system. 6. Remove the Optically Isolated PCI Serial Adapter card. continu
Resumen del contenido incluido en la página 19
Chapter 4: TROUBLESHOOTING If you have any trouble starting your system after installing the card, the card may not be properly seated in the slot. Remove and re-insert it or try a different slot. If you are unable to communicate with the card using your software and hardware devices: 1. Check your pinouts. In RS-422 or RS-485 mode the "A" lines should match your "A" or "-" lines. "B" lines should match your "B" or "+" lines. Note: RS-422/485 pinouts are non-standard. 2. Use the
Resumen del contenido incluido en la página 20
Appendix A: 3PCIOSD1x I/O SCHEMATIC Port 1 I/O Schematic Documentation Number 3PCIOSD1x-3903m Manual Appendix A A-1 A-2 Appendix A Documentation Number 3PCIOSD1x-3903m Manual B&B Electronics Mfg Co – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 B&B Electronics Mfg Co – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 B&B Electronics Ltd – Westlink Comm. Pk. – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-79
