Resumen del contenido incluido en la página 1
User Manual
PCM-9587
Onboard Intel® Celeron M EBX
SBC with Audio, VGA, LCD,
SATA
Resumen del contenido incluido en la página 2
Copyright The documentation and the software included with this product are copyrighted 2008 by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements in the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate an
Resumen del contenido incluido en la página 3
Packing List Before you begin installing your card, please make sure that the following materials have been shipped: •1 PCM-9587 all-in-one single board computer •1 CD disk for utility and drivers •1 startup manual •1 Mini Jumper*10 PCS Package (p/n: 9689000002) 1 ATX power cable (p/n:1700001112) 1 X Heatsink (50*50*30mm) If any of these items are missing or damaged, contact your distributor or sales repr
Resumen del contenido incluido en la página 4
Declaration of Conformity FCC Class A This device complies with the requirements in part 15 of the FCC rules: Operation is subject to the following two conditions: 1.This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for a Class A dig- ital device, pursuant to part 15 of the FCC Rules. These limits are designed to pro-
Resumen del contenido incluido en la página 5
Contents Chapter 1 General Information ............................1 1.1 Introduction ............................................................................................... 2 1.2 Features.................................................................................................... 2 1.3 Specifications ............................................................................................ 2 1.4 Board layout: dimensions.........................................................
Resumen del contenido incluido en la página 6
2.20 USB connectors (CN18,CN20) ............................................................... 16 Table 2.8: CN18: USB port 3/4................................................. 16 Table 2.9: CN20: USB PORT 1/2.............................................. 16 2.21 LCD Backlight connector (CN1).............................................................. 16 2.22 SATA Connector (CN23, CN24) ............................................................. 16 2.23 DIO connector (CN19) ...............
Resumen del contenido incluido en la página 7
Chapter 6 Audio Setup .......................................35 6.1 Introduction ............................................................................................. 36 6.2 Driver installation..................................................................................... 36 6.2.1 Before you begin......................................................................... 36 6.2.2 Windows 2000/XP drivers........................................................... 36 Chapter 7 LAN Con
Resumen del contenido incluido en la página 8
B.16 Printer Port Connector (CN16)................................................................ 57 Table B.16:Printer Port Connector (CN16)................................. 57 B.17 USB Connector (CN18,20) .................................................................... 58 Table B.17:USB Connector (CN18,20)....................................... 58 B.18 DIO Connector (CN19) ........................................................................... 58 Table B.18:DIO Connector (CN19)......
Resumen del contenido incluido en la página 9
Chapter 1 1General Information This chapter gives background information on the PCM-9587. Sections include: Introduction Features Specifications Board layout and dimensions
Resumen del contenido incluido en la página 10
1.1 Introduction The PCM-9587 series is a EBX SBC (Single Board Computer) designed with the powerful Intel Celeron M processor, and Intel 852GM and 6300ESB chipsets, which supports Dynamic Video Memory Technology For maximum performance. PCM- 9587 also supports one 184 PIN DIMM socket for ECC DDR memory up to 1GB. These chipsets are specifically for embedded computing and provide an optimized on-board integrated graphics solution. Other on-board features include 1 EIDE, 2 SATAs, 1 FDD, 1 LPT, 4
Resumen del contenido incluido en la página 11
Chapter 1 General Information Watchdog timer: Winbond W83627, 255 levels timer interval, setup by soft- ware USB: Four USB 2.0 compliant host ports IrDA: N/A GPIO: 8-bit general purpose input/output Expansion: PC/104 Plus(support 8bit ISA, not support ISA DMA mode), PCI and miniPCI Solid State Disk Supports one 50-pin socket for CFC type I/II VGA/LCD Interface Chipset: Intel 852GM Frame buffer: Optimized Shared Memory Architecture, supports up to 64MB frame buffer using system memory
Resumen del contenido incluido en la página 12
1.4 Board layout: dimensions Figure 1.1 Board layout: dimensions (component side) Figure 1.2 Board layout: dimensions (solder side) PCM-9587 User Manual 4
Resumen del contenido incluido en la página 13
Chapter 2 2Installation This chapter explains the setup procedures of PCM-9587 hard- ware, including instructions on setting jumpers and connecting peripherals, switches and indica- tors. Be sure to read all safety pre- cautions before you begin the installation procedure.
Resumen del contenido incluido en la página 14
2.1 Jumpers The PCM-9587 has a number of jumpers that allow you to configure your system to suit your application. The table below lists the functions of the various jumpers. Table 2.1: Jumpers Label Function J1 LCD Voltage Select J2 PC104+ VIO Select J3 Clear CMOS function Select J5 COM2 RS232/422/485 function Select 2.1.1 Jumpers setting drawing Table 2.2: J1: LCD Voltage Select PIN FUNCTION 1-2 +3.3 V* 2-3 +5 V 123 1 23 Table 2.3: J2: PC104+ VIO Select PIN FUNCTION 1-2 VIO = +5 V * 2-3 VIO
Resumen del contenido incluido en la página 15
Chapter 2 Installation Table 2.5: J5: COM2 RS 232/422/485 Select PINS RS-232 RS-422 RS-485 1,2 Open Open Close 3,4 Open Close Open 5,6 Close Open Open 7,9 Close Open Open 8,10 Close Open Open 9,11 Open Close Close 10,12 Open Close Close 13,15 Close Open Open 14,16 Close Open Open 15,17 Open Close Close 16,18 Open Close Close 2 .. .. .... .. .... 18 ○ ○ ■ ■■ ○ ■■ ○ RS-232 ■ □ ○ ■■ ○ ■■ ○ 1.. .. .. .. .. .. ..17 2 ...... .. .. .. ..18 ○ ■ ○ ○ ■■ ○ ■■ RS-422 ■ □ ○ ○ ■■ ○ ■■ 1 .
Resumen del contenido incluido en la página 16
2.2 Connectors On-board connectors link the PCM-9587 to external devices such as hard disk drives, a keyboard, or floppy drives. The table below lists the function of each of the board’s connectors. Table 2.6: Connectors Label Function CN1 LCD Backlight connector CN2 TV-out connector (TV out optional by request) CN3 CD-IN connector CN4 Audio output connector CN5 Power input connector CN6 -12V and -5V connector CN7 VGA connector CN8 LVDS connector CN9 DVI connector CN10 Gigabit LAN connector(Opti
Resumen del contenido incluido en la página 17
Chapter 2 Installation 2.3 Locating jumpers and Connectors Figure 2.1 Jumper & Connector (component side) Figure 2.2 Jumper & Connector (solder side) 9 PCM-9587 User Manual
Resumen del contenido incluido en la página 18
2.4 Setting Jumpers You may configure your card to match the needs of your application by setting jump- ers. A jumper is a metal bridge used to close an electric circuit. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close” a jumper, you connect the pins with the clip. To “open” a jumper, you remove the clip. Sometimes a jumper will have three pins, labeled 1, 2 and 3. In this case you would connect eithe
Resumen del contenido incluido en la página 19
Chapter 2 Installation 2.6 Installing DIMMs The procedure for installing DIMMs is described below. Please follow these steps carefully. The number of pins are different on either side of the breaks, so the module can only fit in one way. DIMM modules have different pin contacts on each side, and therefore have a higher pin density. 1. Make sure that the two handles of the DIMM socket are in the “open” position. i.e. The handles remain leaning outward. 2. Slowly slide the DIMM module along the p
Resumen del contenido incluido en la página 20
2.9 Floppy drive connector (CN14) You can attach up to two floppy drives to the PCM-9587’s on-board controller. This is useful with 34 pin dual FDD cable (part no:1701340603). You can use any combination of 5.25”(360 KB and 1.2MB) and/or 3.5”(720 KB, 1.44MB, and 2.88 MB) drives. An appropriate 34 pin flat cable is required. 2.9.1 Connecting the floppy drive 1. Plug the 34-pin dual FDD-cable connector into CN14 of PCM-9587 board. Make sure that the red wire corresponds to pin one on the connect
