Resumen del contenido incluido en la página 1
Product Manual
®
Momentus 5400.2 Blade
Server
ST9100823AB
ST9808211AB
ST960822AB
ST9408114AB
100367611
Rev. B
August 2007
Resumen del contenido incluido en la página 2
©2004-2007, Seagate Technology LLC All rights reserved. Publication number: 100367611, Rev. B August 2007 Seagate, Seagate Technology and the Wave logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries. Momentus, Seagate- SeaBOARD, SeaFONE, SeaTDD, and SeaTools are either trademarks or registered trade- marks of Seagate Technology LLC or one of its affiliated companies in the United States and/ or other countries. All other trademarks or registere
Resumen del contenido incluido en la página 3
Contents 1.0 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2.0 Drive specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2.1 Specification summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2.2 Formatted capacity . . . . . . . . . . . . . . . . . .
Resumen del contenido incluido en la página 4
ii Momentus 5400.2 Blade Server Product Manual, Rev. B
Resumen del contenido incluido en la página 5
List of Figures Figure 1. Momentus 5400.2 Blade Server PATA disc drive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Figure 2. Typical 5V startup and operation current profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Figure 3. Jumper settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Figure 4. Mounting dimensions—top, side and end view . . . . . . . . . . . . .
Resumen del contenido incluido en la página 6
iv Momentus 5400.2 Blade Server Product Manual, Rev. B
Resumen del contenido incluido en la página 7
1.0 Introduction ® This manual describes the functional, mechanical and interface specifications for the following Seagate ® Momentus 5400.2 Blade Server drives: � ST9100823AB � ST960822AB � ST9808211AB � ST9408114AB These drives provide the following key features: � 5,400-RPM spindle speed and 8-Mbyte buffer combine for superior performance. � Quiet operation. Fluid Dynamic Bearing (FDB) motor. � High instantaneous (burst) data transfer rates (up to 100 Mbytes per second) using Ultra DMA mode 5
Resumen del contenido incluido en la página 8
2 Momentus 5400.2 Blade Server Product Manual, Rev. B
Resumen del contenido incluido en la página 9
2.0 Drive specifications Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate ST9100823AB, ST9808211AB, ST960822AB, and ST9408114AB model drives. 2.1 Specification summary The specifications listed in this table are for quick reference. For details on specification measurement or definition, see the appropriate section of this manual. Ta
Resumen del contenido incluido en la página 10
Table 1: Specifications Drive specification ST9100823AB ST9808211AB ST960822AB ST9408114AB Read/write power (typical) 2.05/2.1 watts Idle mode (typical) 0.99 watts Standby mode 0.2 watts (typical)** Sleep mode 0.2 watts (typical)** Voltage tolerance (including noise) 5V ± 5% 5° to 55°C (operating) Ambient temperature –40° to 70°C (nonoperating) Temperature gradient 20°C (operating) (°C per hour max, noncondensing) 30°C (nonoperating) 5% to 90% (operating) Relative humidity (noncondensing) 5%
Resumen del contenido incluido en la página 11
2.2 Formatted capacity Model Formatted capacity Guaranteed sectors Bytes per sector ST9100823AB 100 Gbytes 195,371,568 512 ST9808211AB 80 Gbytes 156,301,488 512 ST960822AB 60 Gbytes 117,210,240 512 ST9408114AB 40 Gbytes 78,140,160 512 2.3 Default logical geometry Cylinders Read/write heads Sectors per track 16,383 16 63 LBA mode When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1, where n is the number of guaranteed sectors as defined ab
Resumen del contenido incluido en la página 12
2.5 Recording and interface technology Technology Specification Interface Parallel ATA Recording method RLL 0,11 Recording density BPI (bits/inch typical) 703,000 Track density TPI (tracks/inch typical) 115,000 2 Areal density (Gbits/inch max) 86 Spindle speed (RPM) (± 0.2%) 5,400 Internal data-transfer rate OD (Mbytes/sec max) 48.25 I/O data-transfer rate (Mbytes/sec max) 100 (Ultra DMA mode 5) Interleave 1:1 Cache buffer 8 Mbytes (8,192 kbytes) 2.6 Physical characteristics Height (mm) 9.5
Resumen del contenido incluido en la página 13
2.7 Seek time Seek measurements are taken with nominal power at 25°C ambient temperature. All times are measured using drive diagnostics. The specifications below are defined as follows: � Track-to-track seek time is an average of all possible single-track seeks in both directions. � Average seek time is a true statistical random average of at least 5,000 measurements of seeks between random tracks, less overhead. Typical seek times (msec)* Read Write Track-to-track 1.0 1.5 Average 12.5 14.5
Resumen del contenido incluido en la página 14
2.9 Power specifications The drive receives DC power (+5V) through the interface connector. 2.9.1 Power consumption Power requirements for the drives are listed in the table on page 8. Typical power measurements are based on an average of drives tested, under nominal conditions, using 5.0V input voltage at 25°C ambient temperature. • Spinup power Spinup power is measured from the time of power-on to the time that the drive spindle reaches operating speed. � Seek mode During seek mode, the read/
Resumen del contenido incluido en la página 15
2.9.1.1 Typical current profile Figure 2. Typical 5V startup and operation current profile 2.9.2 Conducted noise Input noise ripple is measured at the host system power supply across an equivalent 15-ohm resistive load on the +5 volt line. Using 5-volt power, the drive is expected to operate with a maximum of 100 mV peak-to-peak square-wave injected noise at up to 10 MHz. Note. Equivalent resistance is calculated by dividing the nominal voltage by the typical RMS read/write current. 2.9.3 Volt
Resumen del contenido incluido en la página 16
2.10 Environmental specifications 2.10.1 Ambient temperature Ambient temperature is defined as the temperature of the environment immediately surrounding the drive. Actual drive case temperature should not exceed 40°C (104°F) within the operating ambient conditions. Above 1,000 feet (305 meters), the maximum temperature is derated linearly by 1°C every 1000 feet. Operating 5° to 40°C (41° to 104°F) Nonoperating –40° to 70°C (–40° to 158°F) 2.10.2 Temperature gradient Operating 20°C per hour
Resumen del contenido incluido en la página 17
2.10.5 Shock All shock specifications assume that the drive is mounted securely with the input shock applied at the drive mounting screws. Shock may be applied in the X, Y or Z axis. 2.10.5.1 Operating shock These drives comply with the performance levels specified in this document when subjected to a maximum operating shock of 250 Gs based on half-sine shock pulses of 2 msec. Shocks should not be repeated more than two times per second. 2.10.5.2 Nonoperating shock The nonoperating shock leve
Resumen del contenido incluido en la página 18
2.11 Acoustics Drive acoustics are measured as overall A-weighted acoustic sound power levels (no pure tones). All mea- surements are consistent with ISO document 7779. Sound power measurements are taken under essentially free-field conditions over a reflecting plane. For all tests, the drive is oriented with the cover facing upward. Note. For seek mode tests, the drive is placed in seek mode only. The number of seeks per second is defined by the following equation: (Number of seeks per secon
Resumen del contenido incluido en la página 19
2.13 Reliability Measurement type Specification 14 Nonrecoverable read errors 1 per 10 bits read, max. Mean time between failures 500,000 hours at 25°C ambient temperature (MTBF) 8,760 Power On Hours/year at nominal power. Max case temperature: 40°C at the case measurement location shown in Figure 4. Load/Unload (U/UL) 25°C, 50% relative humidity 600,000 software-controlled power on/off cycles 20,000 hard power on/off cycles 32°C, 80% relative humidity 600,000 software-controlled
Resumen del contenido incluido en la página 20
Korean RRL If these drives have the Korea Ministry of Information and Communication (MIC) logo, they comply with para- graph 1 of Article 11 of the Electromagnetic Compatibility control Regulation and meet the Electromagnetic Compatibility (EMC) Framework requirements of the Radio Research Laboratory (RRL) Ministry of Information and Communication Republic of Korea. These drives have been tested and comply with the Electromagnetic Interference/Electromagnetic Susceptibil- ity (EMI/EMS) for Cla
