Resumen del contenido incluido en la página 1
Product Manual
®
Cheetah NS 10K.2 SAS
ST3600002SS
ST3450802SS
100516228
Rev. C
November 2009
Resumen del contenido incluido en la página 2
Copyright © 2009 Seagate Technology LLC. All rights reserved. Printed in U.S.A. Publication number: 100516228, Rev. C, November 2009 Seagate, Seagate Technology and the Wave logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries. Cheetah, SeaTools and SeaTDD are either trademarks or registered trademarks of Seagate Technology LLC or one of its affiliated companies in the United States and/or other countries. All other trademarks or registered trad
Resumen del contenido incluido en la página 3
Contents 1.0 Scope. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2.0 Standards, compliance and reference documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2.1 Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2.1.1 Electromagnetic compatibility. . . . . . . . . . . . . . . . . . . .
Resumen del contenido incluido en la página 4
6.4.2 Relative humidity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 6.4.3 Effective altitude (sea level) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 6.4.4 Shock and vibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 6.4.5 Acoustics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 6.4.6 Air
Resumen del contenido incluido en la página 5
1.0 Scope ® ® This manual describes Seagate Technology LLC, Cheetah NS 10K.2 SAS (Serial Attached SCSI) disk drives. Cheetah drives support the SAS Protocol specifications to the extent described in this manual. The SAS Inter- ® face Manual (part number 100293071) describes the general SAS characteristics of Cheetah NS 10K.2 SAS and other Seagate SAS drives. Cheetah NS 10K.2 SAS Product Manual, Rev. C 1
Resumen del contenido incluido en la página 6
2.0 Standards, compliance and reference documents The drive has been developed as a system peripheral to the highest standards of design and construction. The drive depends on its host equipment to provide adequate power and environment for optimum performance and compliance with applicable industry and governmental regulations. Special attention must be given in the areas of safety, power distribution, shielding, audible noise control, and temperature regulation. In particular, the drive mu
Resumen del contenido incluido en la página 7
2.2 Compliance 2.2.1 Electromagnetic compliance Seagate uses an independent laboratory to confirm compliance with the directives/standards for CE Marking and C-Tick Marking. The drive was tested in a representative system for typical applications. The selected sys- tem represents the most popular characteristics for test platforms. The system configurations include: • Typical current use microprocessor • 3.5-inch floppy disk drive • Keyboard • Monitor/display • Printer • External modem •Mouse A
Resumen del contenido incluido en la página 8
2.3 Reference documents SCSI Commands Reference Manual Seagate part number: 100293068 SAS Interface Manual Seagate part number: 100293071 Applicable ANSI SAS documents SFF-8323 3.5” Drive Form Factor with Serial Connector SFF-8460 HSS Backplane Design Guidelines SFF-8470 Multi Lane Copper Connector SFF-8482 SAS Plug Connector ANSI INCITS.xxx Serial Attached SCSI (SAS) Standard (T10/1562-D) ISO/IEC 14776-xxx SCSI Architecture Model-3 (SAM-3) Standard (T10/1561-D) ISO/IEC 14776-xxx SCSI P
Resumen del contenido incluido en la página 9
3.0 General description ® Cheetah NS 10K.2 SAS drives provide high performance, high capacity data storage for a variety of systems including engineering workstations, network servers, mainframes, and supercomputers. The Serial Attached SCSI interface is designed to meet next-generation computing demands for performance, scalability, flexibility and high-density storage requirements. Cheetah drives are random access storage devices designed to support the Serial Attached SCSI Protocol as des
Resumen del contenido incluido en la página 10
3.1 Standard features Cheetah NS SAS drives have the following standard features: • Perpendicular recording technology • 1.5 / 3 / 6 Gb Serial Attached SCSI (SAS) interface • Integrated dual port SAS controller • Support for SAS expanders and fanout adapters • Downloadable firmware using the SAS interface • 128 - deep task set (queue) • Supports up to 32 initiators • Jumperless configuration. • User-selectable logical block size (512, 520, 524, or 528 bytes per logical block) • Programmable logi
Resumen del contenido incluido en la página 11
3.5 Formatted capacities Standard OEM models are formatted to 512 bytes per block. The block size is selectable at format time and must be a multiple of 4 bytes. Users having the necessary equipment may modify the data block size before issuing a format command and obtain different formatted capacities than those listed. To provide a stable target capacity environment and at the same time provide users with flexibility if they choose, Seagate recommends product planning in one of two modes: 1
Resumen del contenido incluido en la página 12
4.0 Performance characteristics This section provides detailed information concerning performance-related characteristics and features of Cheetah NS SAS drives. 4.1 Internal drive characteristics ST3600002SS ST3450802SS * Drive capacity 600 450 GB (formatted, rounded off value) Read/write data heads 8 6 Tracks per inch 165,000 165,000 TPI Peak bits per inch 1,347 1,347 kBPI 2 Areal Density 225 225 Gb/inch Internal data rate 1.01 to 1.84 1.01 to 1.84 Gb/sec (variable with zone) Disk rotation s
Resumen del contenido incluido en la página 13
4.2.2 Format command execution time (minutes) ST3600002SS ST3450802SS Maximum (with verify) 182 129 Maximum (without verify) 101 68 Execution time measured from receipt of the last byte of the Command Descriptor Block (CDB) to the request for a Status Byte Transfer to the Initiator (excluding connect/disconnect). When changing sector sizes, the format times shown above may need to be increased by 30 minutes. 4.2.3 General performance characteristics Sustainable disk transfer rate*: Minimum 82
Resumen del contenido incluido en la página 14
4.4 Prefetch/multi-segmented cache control The drive provides a prefetch (read look-ahead) and multi-segmented cache control algorithms that in many cases can enhance system performance. Cache refers to the drive buffer storage space when it is used in cache operations. To select this feature, the host sends the Mode Select command with the proper values in the applicable bytes in page 08h. Prefetch and cache operations are independent features from the standpoint that each is enabled and di
Resumen del contenido incluido en la página 15
The buffer segmentation scheme is set up or changed independently, having nothing to do with the state of RCD. When a write command is issued, if RCD=0, the cache is first checked to see if any logical blocks that are to be written are already stored in the cache from a previous read or write command. If there are, the respective cache segments are cleared. The new data is cached for subsequent Read commands. If the number of write data logical blocks exceed the size of the segment being writ
Resumen del contenido incluido en la página 16
5.0 Reliability specifications The following reliability specifications assume correct host and drive operational interface, including all inter- face timings, power supply voltages, environmental requirements and drive mounting constraints. 8 Seek error rate: Less than 10 errors in 10 seeks 1 Read Error Rates 12 Recovered Data Less than 10 sector in 10 bits transferred (OEM default settings) 16 Unrecovered Data Less than 1 sector in 10 bits transferred 21 Miscorrected Data Less than 1 sector
Resumen del contenido incluido en la página 17
a seek positioning error (Error code = 15h or 02h) will be reported with a Hardware error (04h) in the Sense 8 Key. Recoverable seek errors are specified at Less than 10 errors in 10 seeks. Unrecoverable seek errors (Sense Key = 04h) are classified as drive failures. 5.1.4 Interface errors An interface error is defined as a failure of the receiver on a port to recover the data as transmitted by the device port connected to the receiver. The error may be detected as a running disparity err
Resumen del contenido incluido en la página 18
5.2.4 S.M.A.R.T. S.M.A.R.T. is an acronym for Self-Monitoring Analysis and Reporting Technology. This technology is intended to recognize conditions that indicate imminent drive failure and is designed to provide sufficient warning of a failure to allow you to back up the data before an actual failure occurs. Note. The drive’s firmware monitors specific attributes for degradation over time but can’t predict instanta- neous drive failures. Each monitored attribute has been selected to monitor a
Resumen del contenido incluido en la página 19
the interval expires, the error rate is considered to be unacceptable. If the number of errors does not exceed the threshold before the interval expires, the error rate is considered to be acceptable. In either case, the inter- val and failure counters are reset and the process starts over. Predictive failures S.M.A.R.T. signals predictive failures when the drive is performing unacceptably for a period of time. The firm- ware keeps a running count of the number of times the error rate for each
Resumen del contenido incluido en la página 20
The most thorough option is the extended test that performs various tests on the drive and scans every logical block address (LBA) of the drive. The short test is time-restricted and limited in length—it does not scan the entire media surface, but does some fundamental tests and scans portions of the media. If DST encounters an error during either of these tests, it reports a fault condition. If the drive fails the test, remove it from service and return it to Seagate for service. 5.2.7.1 DS
