Resumen del contenido incluido en la página 1
3-862-158-13(1)
CDU948S
CD-R Drive Unit
CDU948S
CD-R Drive Unit
User’s Guide
User’s Guide
©1997 by Sony Corporation Printed in Japan
Resumen del contenido incluido en la página 2
Owner’s Record The model and serial numbers are located on the bottom of the drive. Record these numbers in the spaces provided below. Refer to them whenever you call upon your sales representative regarding this product. Model No. Serial No. Safety Regulations WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. CAU
Resumen del contenido incluido en la página 3
This unit uses CD-R discs with the following mark. This unit uses CD-ROM discs with the following mark. When you use this unit as a CD player, use compact discs with the following mark. WARNING — For the customers in U.S.A. You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Resumen del contenido incluido en la página 4
Contents Introduction 5 Location and Function of Parts and Controls 6 Front Panel ......................................................................................... 6 Rear Panel .......................................................................................... 7 Precautions 8 Example of System Setup 9 Installing the Drive Unit into the Computer 10 Getting Started ................................................................................. 10 Setting the Jumpers ..............
Resumen del contenido incluido en la página 5
Introduction The CDU948S is a drive unit for CD-R discs, which stores a maximum of 650 Mbytes of digital data. The drive unit has the following features: • Reads and writes data in each CD-ROM, CD-ROM XA and Multi-Session standard formats. • Reads standard CD-DA (“Red Book”) encoded discs, and reads and writes CD-R discs conforming to “Orange Book Part II.” • Supports the following write modes: Disc at once, Session at once, Track at once, Variable packet, Fixed packet and Multisession. • Output
Resumen del contenido incluido en la página 6
Location and Function of Parts and Controls Front Panel CD Caddy CD Caddy 1 1 1 1 1Caddy insertion slot Accepts a caddy loaded with a CD-ROM or CD-R disc. 2 2 2 2 2Emergency eject hole Insert a fine rod into this hole to eject a caddy manually in emergencies. 3 3 3 3 3Eject button Ejects the caddy from the drive unit. 4 4 4 4 4Busy indicator This indicator shows the unit’s status in various phases of operation. * Seek, read and write: Flashes amber * Error: Lights up amber and stays lit When t
Resumen del contenido incluido en la página 7
Rear Panel 1 1 1 1 1Jumper block for SCSI bus Specify assignment of the SCSI bus. 2 2 2 2 2Terminators The terminator resistors are inserted into the sockets. Remove the resistors when the SCSI bus is to be terminated externally. Note: Some models are shipped without terminators. When installing the terminators, orient them so that the GND pin (the end marked with a dot) is toward the right side of the socket. 3 3 3 3 3Power-in connector Connect to the power supply of the host computer. 4 4 4 4
Resumen del contenido incluido en la página 8
Precautions n Installation • Avoid placing the drive in a location subject to: –high humidity –high temperature –excessive dust –mechanical vibration –direct sunlight. We recommend to use the drive in a horizontal position. Do not use it in a tilted position. n Operation • Do not move the drive during operation. This may cause it to malfunction during reading or writing. • Avoid exposing the drive to sudden changes in temperature as condensation may form on the lens inside the drive as a result.
Resumen del contenido incluido en la página 9
Example of System Setup To use the CD-R device, the following components are required: • Computer (IBM-PC/AT* compatible) • SCSI-Host adapter • SCSI-Interface cable (50 to 50 pin flat cable) • Software (Device driver, utilities) * IBM-PC/AT is a registered trademark of International Business Machines Corporation. Example of System Setup 9
Resumen del contenido incluido en la página 10
Installing the Drive Unit into the Computer As you go through this section, you may wish to refer to your computer’s manual for a more detailed description of how to install internal drives. Getting Started • Prepare the necessary parts and tools that have not been supplied: –Screwdriver –four screws 3 mm in diameter (Screws must not extend more than 4.0 mm into the side panels or the bottom plate.) –two mounting rails if your computer has mounting tracks. • Unplug the computer and disconnect th
Resumen del contenido incluido en la página 11
Remove the jumper to set to OFF, and install the jumper to set to ON. The recommended jumper is AMP* Shunts (14227-1), JAE** Short Socket (PS-2SH4-1) or equivalent. The following table shows the function of each jumper. Jumper Function DEVICE The setting of this jumper determines whether the TYPE SCSI device type code in the inquiry data is WO or CD-ROM. ON: WORM OFF: CD-ROM ID SELECT Assign the drive unit’s ID number by setting these jumpers to ON or OFF. Do not assign the same number as one us
Resumen del contenido incluido en la página 12
Opening the Computer 1 If your computer has its rear side covered by a plastic panel attached with plastic hook pad, pull it off. 2 Remove the cover mounting screws. 3 Remove the cover of the computer. Installing the Drive Unit into the Computer 12
Resumen del contenido incluido en la página 13
Connecting the Drive Attach one end of the flat cable (SCSI cable) to the connector on the rear of the CD-R drive. Note: The red edge of the flat cable should be positioned next to the power supply connector. It is important that this cable be connected firmly and correctly. Installing the Drive Unit into the Computer 13
Resumen del contenido incluido en la página 14
n Audio output connector The audio output connector recommended is Molex 5159PBT contacts and 5051-04 housing or 5103 PBT contacts and 5102-04 housing. Pin assignment Mounting the Drive 1 Route the flat cable through the drive bay from the front of the computer and insert the CD-R drive into the bay as shown. Secure the CD-R drive to the frame by using the prepared screws. Note: If you cannot secure the CD-R drive to the drive bay, you may need to install slide rails (not included) to the CD-R d
Resumen del contenido incluido en la página 15
2 Locate an available power supply cable inside your computer and connect it to the power supply connector on the rear of the CD-R drive as shown. + + - - Caution: Improper connection may damage the drive and void the warranty. n Frame ground When normally installed, the drive unit is not in contact with the host computer directly and should be grounded. Connect the frame ground tab to one of the host computer’s ground cables. The frame ground cable recommended has a AMP 1-480435-0 housi
Resumen del contenido incluido en la página 16
Host Adapter Installation Connect the free end of the flat cable to the existing SCSI host adapter card and install the host adapter in the computer by inserting it securely in a system expansion slot. Refer to the operating instructions of the host adapter for complete instructions on its installation and the assignment of its switches. Notes: • The red edge of the flat cable must be closest to pin number 1 of the interface card connector. • The following illustration is a sample system configu
Resumen del contenido incluido en la página 17
Termination • If the CD-R drive is connected at the end of the SCSI chain, keep the drive terminator mounted at the drive. • If the CD-R drive isn’t the last device at the SCSI bus, remove the termination from the CD-R drive and make sure that the last device at the SCSI bus has a proper termination installed. • Be aware that the SCSI bus needs to be terminated at each end of the SCSI bus cable. Closing the Computer 1 Replace the cover on the computer, being careful to reinstall all screws that
Resumen del contenido incluido en la página 18
Installing the Software Driver MSCDEX and the device driver for an ordinary SCSI CD-ROM drive can be used when using the CDU948S as a SCSI CD-ROM drive. Use the device driver for a CD-R drive when using the CDU948S as a recordable drive. Be sure to install the device driver before operating the drive. Refer to the manual supplied with the host adapter for instructions. Installing the Software Driver 18
Resumen del contenido incluido en la página 19
Using Discs and Caddies Loading a Caddy with a Disc 1 To open the caddy lid, press the tabs on the both sides of the caddy at the end opposite to the shutter. 2 Set a disc, with its label upward, in the caddy. Be careful not to touch the recording surface when setting a CD- R disc in the caddy. Data cannot be recorded if the recording surface is contaminated. Using Discs and Caddies 19
Resumen del contenido incluido en la página 20
3 Close the lid firmly. Important: • Do not drop the disc or the caddy. • The caddy is designed so that its shutter automatically opens when it is inserted into the drive unit. Do not open the shutter manually and touch the disc. • Data cannot be recorded if the recording surface is contaminated. • The caddy is precisely adjusted at the factory. Do not disassemble it. 20 Using Discs and Caddies
