Resumen del contenido incluido en la página 1
Mac Pro
Processor Cage Fans, Front and Rear
Replacement Instructions
Note: Follow these instructions carefully. Failure to do so could damage your equipment and
First Steps
void its warranty.
1 Shut down computer.
2 Wait 10 minutes.
Warning: Parts inside
computer can be very
hot. Allow computer
to cool down before
continuing.
3 Unplug all external
cables except power
cord.
4 Touch metal PCI cover
on back of computer.
5 Unplug power cord.
Opening the
Computer
1 Hold side access
panel
Resumen del contenido incluido en la página 2
Required Tools • Phillips #2 screwdriver • RIght-angle, 2.5 mm hex driver • Flatblade screwdriver • Long-handled Phillips #1 screwdriver Removing the Installed Fans Fans are installed in processor cage. To access fans, you must first remove: • Hard drive in far-left drive bay • Graphics card in slot 1 • Processor tray • PCIe fan • Processor cage Hard Drive 1 Make sure latch on back panel is up, so that drive is unlocked. 2 Pull hard drive out of far-left drive bay. © 2009 Apple Inc.
Resumen del contenido incluido en la página 3
Graphics Card 3 Locate graphics card in slot 1. 4 Using Phillips #1 screwdriver, loosen 2 captive screws securing card’s bracket to enclosure. 5 Remove bracket from enclosure. © 2009 Apple Inc. All rights reserved. 073-1254 Rev. A 3
Resumen del contenido incluido en la página 4
Note: Card is held in place by retention bar. Following two steps explain how to release bar. 6 Press button on PCIe fan. 7 Move fan to left, which releases retention bar. Note: Some graphics cards require 1 or 2 booster cables connecting card to auxiliary power connectors on backplane board. If your card has booster cables, disconnect them from backplane board. © 2009 Apple Inc. All rights reserved. 073-1254 Rev. A 4
Resumen del contenido incluido en la página 5
8 Holding card by top corners, pull it up out of slot. 9 Remove card from computer. Checklist for handling card: • When removing or installing card, handle it only by the edges. Do not touch its connectors or any components. • Don’t rock card from side to side; instead, lift card straight up from connecotr to remove it, and press card straight into slot to install it. • Don’t force card. If you meet a lot of resistance, pull card out. Check connector and slot for damage or obstructions,
Resumen del contenido incluido en la página 6
Processor Tray 10 Locate processor tray. 11 Press down and release 2 latches on front of processor tray. © 2009 Apple Inc. All rights reserved. 073-1254 Rev. A 6
Resumen del contenido incluido en la página 7
12 Holding tray by latches, lift it out of computer. 13 Place tray DIMM side up on soft, clean cloth. PCIe Fan 14 Locate PCIe fan. © 2009 Apple Inc. All rights reserved. 073-1254 Rev. A 7
Resumen del contenido incluido en la página 8
15 Remove 2 screws. 16 Slide fan up and out of computer. Processor Cage 17 Locate processor cage. © 2009 Apple Inc. All rights reserved. 073-1254 Rev. A 8
Resumen del contenido incluido en la página 9
18 Disconnect 3 cables from logic board. 19 Using long-handled Phillips #1 screwdriver, loosen 6 captive screws. 20 Rotate computer to stand vertically. Using 2.5 mm hex driver, remove 5 mushroom- head screws. Note: Processor cage includes two fans, one at each end of cage. Before removing cage from enclosure, you must release 2 latches on each fan and push fans partway into cage. 21 To release 2 latches holding front fan to cage, press down on bottom of cage while using flatblade
Resumen del contenido incluido en la página 10
24 Lift cage out of enclosure. Processor Cage Fans 25 Locate processor cage fans. © 2009 Apple Inc. All rights reserved. 073-1254 Rev. A 10
Resumen del contenido incluido en la página 11
26 Release fan cables from clips on bottom of processor cage. 27 Release 4 latches on front fan and slide fan out of cage. Note: Latch #4 is on inside of cage. 28 Repeat above step for rear fan. © 2009 Apple Inc. All rights reserved. 073-1254 Rev. A 11
Resumen del contenido incluido en la página 12
Installing the Replacement Fans 1 IPosition front fan in cage. 2 Slide fan back until it engages with the 4 latches. 3 Repeat above two steps for rear fan. 4 Re-insert fan cables in clips on bottom of processor cage. © 2009 Apple Inc. All rights reserved. 073-1254 Rev. A 12
Resumen del contenido incluido en la página 13
Processor Cage Important: Before you re- install cage into enclosure, fans must be inserted partway into cage. 5 Position cage in enclosure. 6 Slide front and rear fans into place, so that they engage with latches. 7 Replace and tighten 5 mushroom-head screws. 8 Secure 6 captive screws. 9 Reconnect 3 cables. PCIe Fan 10 Slide fan into enclosure so that fan tabs engage with slots on metal cage. 11 Press down until fan clicks into place in connector. 12 Replace 2 screws. © 2009 Apple
Resumen del contenido incluido en la página 14
Processor Tray 13 Holding tray by latches, lower it into processor cage. 14 Make sure latches are closed flush with front of processor tray. Graphics Card 15 Reinstall graphics card in slot 1. Note: Align card’s connector with expansion slot and press down until connector is inserted all the way into slot. If installing a 12-inch card, make sure card engages correct slot in PCIe card guide. 16 If card includes booster cables, reconnect cables. 17 Slide PCIe fan to the right to l
Resumen del contenido incluido en la página 15
Hard Drive 19 Replace hard drive in far-left drive bay. Closing the Computer 1 Replace access panel. Note: Make sure latch is up before you replace panel. If latch is down, panel will not seat correctly. 2 Push latch down to close and secure access panel. Warning: Never turn on computer unless all its internal and external parts are in place and it is closed. Operating computer when open or missing parts can cause damage or injury. Apple Inc. © 2009 Apple Inc. All rights reserv
