Resumen del contenido incluido en la página 1
NGA 2000
Software Manual
CLD - Analyzer Module
Chemiluminescence - Measurement
(combined with NGA 2000 - Platform / MLT - Analyzer)
CLD Software Version 2.3
(Platform / MLT Software Version 3.1.X)
1. Edition 04/98
Catalog No.: 90 003 749
Managing The Process Better
90003749(1) [NGA-e (CLD-Software 2.3 / MLT-Software 3.1.X)] 04/98
Resumen del contenido incluido en la página 2
This Operation Manual includes information about the operation of the instrument. Information about the additional indications and notes regarding maintenance, troubleshooting and repair are found in the accompanying Maintenance & Operation Manual. Troubleshooting, component replacement and internal adjustments must be made by qualified service personnel only. Fisher-Rosemount GmbH & Co does not take responsibility for any omissions or errors in this manual. Any liability for direct or indirect
Resumen del contenido incluido en la página 3
Contents 1 Introduction 1 - 1 2 Structure of Menus 2 - 1 3 Display and Keyboard 3 - 1 3.1 Starting and Initializing ................................ ................................ ................... 3 - 1 3.2 Display and Function ................................ ................................ ...................... 3 - 1 3.3 Operating Keys ................................ ................................ .............................. 3 - 2 3.4 Lines ................................ .......
Resumen del contenido incluido en la página 4
5 Expert Controls and Set up 5 - 1 5.1 Analyzer Module Set up 5 - 3 5.1.1 Calibration/Calibration Gas List ................................ ................................ ...... 5 - 4 5.1.2 Calibration Parameters ................................ ................................ ................... 5 - 9 5.1.3 Gas Measurement Parameters ................................ ................................ ...... 5 - 11 5.1.4 Linearization Parameters ................................ ................
Resumen del contenido incluido en la página 5
6 Technical Level Configuration 6 - 1 6.1 System Set up 6 - 3 6.1.1 Main Display Configuration ................................ ................................ ............ 6 - 4 6.1.2 Front Panel Control ................................ ................................ ........................ 6 - 9 6.1.3 Date and Time Set up ................................ ................................ .................... 6 - 11 6.1.4 Module Binding ................................ ......................
Resumen del contenido incluido en la página 6
IV 90003749(1) [ NGA-e (Software CLD 2.3/MLT 3.1.X)] 04/98 NGA 2000
Resumen del contenido incluido en la página 7
1 Introduction This software manual describes step by step how to operate successfully with the ½ 19" and 19" MLT analyzer module and analyzer of the NGA 2000 Series from . Chapter two shows the structure of the software menus. Chapter three describes the display and the keyboard of the analyzer. Chapter four describes the basic controls with detailed illustrations. So you can easily compare the actual display of the analyzer module with the illustrations of the manual. Chapter five describes th
Resumen del contenido incluido en la página 8
The following illustrations shall make plain the connection between the hardware configu- ration and the software setup of the modules: Local Analyzer Control Auxiliary I/O's Modules (AM's) Module (CM) Modules (see 5.1.17) SIO MLT (see 5.2.1) (see 5.1.18) (other manuals) CLD (see 5.2.2) (other manuals) (other manuals) PMD Local Analyzer Control Auxiliary I/O's Modules (AM's) Modul (CM) Modules SIO DIO 1 - 2 90003749(1) [ NGA-e (Software CLD 2.3/MLT 3.1.X)] 04/98 Platform MLT Analyzer NGA 2000 PM
Resumen del contenido incluido en la página 9
2 Structure of Menus "AM". System set up... Service menus... Diagnostic menus... Other module diagnostic menus... Listing of all modules... - - - - - utput Module). O nput-/ I Expert analyzer controls... Auxiliary module controls... System set up... Analyzer module set up... Auxiliary module set up... System calibration... - - - - - - odule), I/O ( M ontrol C x odule), CM ( M nalyzer A In the menu structure shown above, you will find the most important ramifications of the MLT software 3.1.X f
Resumen del contenido incluido en la página 10
2 - 2 90003749(1) [ NGA-e (Software CLD 2.3/MLT 3.1.X] 04/98 NGA 2000
Resumen del contenido incluido en la página 11
3 Display and Keyboard 3.1 Starting and Initializing After switching on the CLD analyzer module (in a platform or part of a NGA network), the initialization procedure will be performed. A self control of the analyzer modules or the analyzer(s) is running. You can see a sequence of several displays. They show the status of initialization, revision notes of the MLT software and the tag. At the end of this procedure you can see the single component display of channel one. It is the origin to all
Resumen del contenido incluido en la página 12
3.3 Operating Keys 95.00 ppm NOx 0 Range: 4 250 Sample press.: 340 hPa Cursor keys: Detector temperature: 0.5 C ↑ ↑ -key / ↓ ↓ -key: Block temperature: 51.5 C ♦ Converter temp.: 360 C ♦ Alteration of numbers, F1 F2 F3 F4 F5 ← ← -key/ → → -key: ♦ between the pages of a menu ♦ Selection of digits Function Keys: Enter Key: ♦ ♦ ♦ The current function depends on the menu selected ♦ To start a selected function ♦ The softkey legend is shown on ( : → → -key) ♦ To go into a menu (via menu line) 3.4 L
Resumen del contenido incluido en la página 13
3 Display and Keyboard Text Line Basic Controls Measurement range number: 4 Line of Variables Range upper limit: 250.0 ppm Range and functional control: LOCAL Ranges with valid calibration: 4 Calibration status: Status: STANDBY Measurement mode: Ozonator status: On Ozonator power: Enabled F1 F2 F3 F4 F5 Zero/span calibration Measurement range number: 3 Zero gas concentration: 0.0 ppm Span gas concentration: 100.0 ppm Sample flow: Raw measurement signal: 521590 Measurement gas: NO/NOx toggle
Resumen del contenido incluido en la página 14
MENU ♦ Change from the single component display to the main menu or from several submenus to higher menus. ESCAPE or <<< ♦ Changing back to the last menu page selected. ♦ Reset of a changed but not confirmed parameter to the former value resp. to zero. BACK ♦ Reset of a changed but not confirmed parameter to the former value. LOCK ♦ Lock of any operation level, if activated. Each of the three operation levels has to be activated separately. ♦ F4 key of the main menu. NEXT ♦ Change of the channel
Resumen del contenido incluido en la página 15
3 Display and Keyboard 3.7 The STATUS Key From the single component display or from the main menu you can change with the F2 key (STATUS) to the menu "Current measurement parameters": Current measurement parameters Analyzer gas measured: Measurement range number: 3 Range change control: LOCAL Linearization mode: Disabled Analyzer operational state: STANDBY NORMAL Alarms reported: FAILURE F1 F2 F3 F4 F5 Current measurement parameters Response time: 3.0 s Bypass flow: Capillary pressure: 340 hPa
Resumen del contenido incluido en la página 16
3 - 6 90003749(1) [ NGA-e (Software CLD 2.3/MLT 3.1.X)] 04/98 NGA 2000
Resumen del contenido incluido en la página 17
4 Basic Controls In the chapter "Basic Controls" you will find the most important functions to set up your CLD analyzer module via an NGA front panel: 1) Measurement p. 4 - 3pp (Chapter 4.1.1 and 4.1.2, p. 4-3 to 4-6, are only important for systems with several channels.) 2) Calibration p. 4 - 21pp All steps are figured with detailed illustrations and operation instructions. In the left column you can see display and keyboard of the NGA front panel. In the right column you can read the instruct
Resumen del contenido incluido en la página 18
4 - 2 90003749(1) [ NGA-e (Software CLD 2.3/MLT 3.1.X)] 04/98 NGA 2000
Resumen del contenido incluido en la página 19
4.1.1 Measurement - Multi Component Display: Change of Channel ⇒ ⇒ Change to the multi component display 95.00 ppm NOx F1 Press 0 can multi component from component F1 F2 F3 F4 F5 ⇒ ⇒ Enable the selecting: ">" 95.00 F1 Press 45.00 333.0 or 150.0 If of 20.00 modules are combined to of F1 F2 F3 F4 F5 Then, a of possible ! ⇒ ⇒ Select any channel 95.00 Press or 45.00 as often as 333.0 put the > - mark into the 150.0 20.00 Example : from NO (CLD) to X CO (MLT F1 F2 F3 F4 F5 9000
Resumen del contenido incluido en la página 20
⇒ ⇒ Change to the single component display of the channel 95.00 selected 45.00 F1 333.0 Press 150.0 20.00 F1 F2 F3 F4 F5 ⇒ ⇒ Single component display of the channel selected 45.00 ppm CO will appear 0 Failure: F1 F2 F3 F4 F5 4 - 4 90003749(1) [ NGA-e (Software CLD 2.3/MLT 3.1.X)] 04/98 NGA 2000 INFO NEXT MENU STATUS DISPLAY No No Maintenance Request: No Function Control: 25.0 C Temperature: 250 Range: 2 MLT25/CH1/R2 INFO TAGS OFF STATUS SELECT %O2 MLT25/CH4/R2 ppm NO MLT25/CH3/R2 ppm SO2 MLT25
