Resumen del contenido incluido en la página 1
LAP24EULBA
LAP24EULFR
NOTEBOOK CART ASSEMBLY
WITH TIMER
Assembly Instructions for:
LAP24EULBA
INTERIOR E-UNIT
REPOSITIONING / REPLACEMENT
CAUTION: RISK OF ELECTRICAL SHOCK.
AND
DO NOT PLUG INTO ANOTHER
TIMER REPLACEMENT
RELOCATABLE POWER TAP.
Parts List
Qty. Part No. Description
NO TV/MONITOR TO BE
1 LAP24EULBA Cart Assembly, e-units at back
USED ON TOP OF CART
LAP24EULFR Cart Assembly, e-units at front
Tools Required MAXIMUM WEIGHT OF ACCESSORIES
ON TOP OF CART: 25 LBS.
Philips screwdriver
Th
Resumen del contenido incluido en la página 2
E-Unit power timer assembly cord bottom shelf Front View bracket assembly DETAIL 'B' clip bracket assembly DETAIL 'A'
Resumen del contenido incluido en la página 3
front-left front-right Step 2 Remove front-left E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf channel and set it aside. Remove front-right E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf channel and set it aside. DETAIL 'C' Step 3 Remove 14 screws (2 per shelf) from rear panel that secure the 7 interior shelves (see DETAIL 'C').
Resumen del contenido incluido en la página 4
mounting tab DETAIL 'D' Step 4 Remove each interior shelf by carefully pushing upward (to release shelf from mounting tabs) shown in Detail 'D', then carefully sliding out. Set each shelf aside.
Resumen del contenido incluido en la página 5
cutout window clip-rear Step 5 Reinstall the E-Units (set aside from being removed from the front) as follows: 1. Rotate the E-Unit 180 degrees (from original position). 2. Position to the rear of cart. 3. Tilt in and set bottom in back, in front of rear panel cutout window. 4. Grip the top and tilt to the upright position, underneath top panel bracket. When repositioned correctly, the E-Unit power switch should be visible from rear panel cutout window. Reinstall the E-Unit bracket assemblies (m
Resumen del contenido incluido en la página 6
tab notch Step 6 Reinstall the 7 interior shelves as follows: 1. Carefully slide in the shelf with notch, at the bottom position (the notch will rest on the bracket tab). (Make sure that the shelf flanges are ALL seated into the mounting tabs.) 2. Slide in all remaining shelves into position as the bottom shelf. DETAIL 'E' Step 7 Reinstall 14 screws to rear panel that will secure the 7 interior shelves (see DETAIL 'E). DO NOT OVER TIGHTEN SCREWS. Installation is now complete and ready for
Resumen del contenido incluido en la página 7
NOTE: UNPLUG CART (TIMER) POWER CORD FROM POWER SOURCE BEFORE STARTING E-UNIT REPOSITIONING: 'REAR TO FRONT' DETAIL 'A' Step 1 Remove 14 screws (2 per shelf) from rear panel that secure the 7 interior shelves (see DETAIL 'A'). mounting tab DETAIL 'B'
Resumen del contenido incluido en la página 8
Step 2 With both doors open, remove each interior shelf by carefully pushing upward (to release shelf from mounting tabs) shown in Detail 'B', then carefully sliding out. Set each shelf aside. E-Unit power cord timer assembly Front View Carefully unplug the power cords of the E-Units from the timer assembly (see Front View) and unclip the power cords from the clips at the rear of cart. Loosen the screw holding the E-Unit bracket assembly and remove all 4 bracket assemblies (see DETAILS 'D' and
Resumen del contenido incluido en la página 9
DETAIL 'D' DETAIL 'E' DETAIL 'D' rear-left rear-right Step 3 Remove rear-left E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf bracket and set it aside. Remove rear-right E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf bracket and set it aside.
Resumen del contenido incluido en la página 10
notch tab Step 4 Reinstall the 7 interior shelves as follows: 1. Carefully slide in the shelf with notch at the bottom position (the notch will rest on the bracket tab). (Make sure that the shelf flanges are ALL seated into the mounting tabs.) 2. Slide in all remaining shelves into position as the bottom shelf. DETAIL 'F Step 5 Reinstall 14 screws to rear panel that will secure the 7 interior shelves (see DETAIL 'F'). DO NOT OVER TIGHTEN SCREWS.
Resumen del contenido incluido en la página 11
offset clip Step 6 Reinstall the E-Units (set aside from being removed from the rear) as follows: 1. Rotate the E-Unit 180 degrees (from original position). 2. Position to the front of cart. 3. Tilt in and set against offset of bottom panel (of cart). 4. Grip the top and tilt to the upright position. When repositioned correctly, the E-Unit power switch should face the front. Reinstall the E-Unit bracket assemblies (make sure that the top flange of the E-unit is aligned with the slot in the brack
Resumen del contenido incluido en la página 12
NOTE: UNPLUG CART (TIMER) POWER CORD FROM POWER SOURCE BEFORE STARTING E-UNIT REPLACEMENT: 'REAR LOCATION' DETAIL 'A' Step 1 Remove 14 screws (2 per shelf) from rear panel that secure the 7 interior shelves (see DETAIL 'A'). mounting tab DETAIL 'B'
Resumen del contenido incluido en la página 13
Step 2 With both doors open, remove each interior shelf by carefully pushing upward (to release shelf from mounting tabs) shown in Detail 'B', then carefully sliding out. Set each shelf aside. E-Unit power timer assembly cord Front View Carefully unplug the power cord(s) of the E-Unit(s) from the timer assembly (see Front View) and unclip the power cord(s) from the clip(s) at the rear of cart. Loosen the screw holding the E-Unit bracket assembly and remove each bracket assembly (see DETAILS 'C
Resumen del contenido incluido en la página 14
DETAIL 'C' DETAIL 'D' rear-left rear-right Step 3 Remove E-Unit(s) by griping the top and tilt it side ways until it clears the underside of the cart interior shelf bracket and set it aside.
Resumen del contenido incluido en la página 15
cutout window clip Step 4 Carefully install replacement E-Unit(s) into position by placing bottom in first and tilting in sideways to the top. When repositioned correctly, the E-Unit(s) power switch should be visible from rear panel cutout window. Reinstall the E-Unit bracket assemblies (make sure that the top flange of the E-unit is aligned with the slot in the bracket assembly) and tighten screws securely. Plug in the E-Unit(s) power cord(s) into the bottom outlet(s) of the timer assembly. Pre
Resumen del contenido incluido en la página 16
tab notch Step 5 Reinstall the 7 interior shelves as follows: 1. Carefully slide in the shelf with notch, at the bottom position (the notch will rest on the bracket tab). (Make sure that the shelf flanges are ALL seated into the mounting tabs.) 2. Slide in all remaining shelves into position as the bottom shelf. DETAIL 'E' Step 6 Reinstall 14 screws to rear panel that will secure the 7 interior shelves (see DETAIL 'E). DO NOT OVER TIGHTEN SCREWS. Installation is now complete and ready for
Resumen del contenido incluido en la página 17
NOTE: UNPLUG CART (TIMER) POWER CORD FROM POWER SOURCE BEFORE STARTING E-UNIT REPLACEMENT: 'FRONT LOCATION' SEE DETAIL 'B' bottom shelf SEE DETAIL 'A' Step 1 Open both front doors of cart to access E-Unit(s). From underneath the bottom shelf, carefully unplug the power cord of the E-Unit(s) from the timer assembly (see Front View) and unclip the power cord(s) from the bottom of cart. Loosen the screw holding the E-Unit bracket assembly and remove (2) bracket assemblies of the E-Unit(s) to be
Resumen del contenido incluido en la página 18
bracket assembly clip DETAIL 'B' bracket assembly DETAIL 'A' front-left front-right Step 2 Remove E-Unit(s) by griping the top and tilt it side ways until it clears the underside of the cart interior shelf channel and set it aside.
Resumen del contenido incluido en la página 19
front-left front-right bottom shelf Step 3 Carefully install replacement E-Unit(s) into position by placing bottom in first and tilting it in sideways to the top. When repositioned correctly, the E-Unit(s) power switch should face the front. Reinstall the E-Unit bracket assemblies (make sure that the top flange of the E-unit is aligned with the slot in the bracket assembly) and tighten screws securely. Plug in the E-Unit power cord(s) into the bottom outlet(s) of the timer assembly (located unde
Resumen del contenido incluido en la página 20
NOTE: UNPLUG CART (TIMER) POWER CORD FROM POWER SOURCE BEFORE STARTING TIMER REPLACEMENT: 'E-UNIT AT REAR LOCATION' DETAIL 'A' Step 1 Remove 6 screws (2 per shelf) from rear panel that secure the 3 bottom interior shelves (see DETAIL 'A'). mounting tab DETAIL 'B'
