Resumen del contenido incluido en la página 1
Parts Manual
Large Frame
Walk-Behind Snowthrowers
9.5HP Snowthrowers
Mfg. No. Description
1694867 9560E, 9.5HP Snowthrower
1694914 9560EX, 9.5HP Snowthrower (CE)
10.5HP Snowthrowers
Mfg. No. Description
1694847 10560E, 10.5HP Snowthrower
1694848 10560EX, 10.5HP Snowthrower (CE)
11.5HP Snowthrowers
Mfg. No. Description
1694849 11570E, 11.5HP Snowthrower
1694850 E11570, 11.5HP Snowthrower (CE)
13HP Snowthrowers
Mfg. No. Description
1694851 1380E, 13HP Snowthrower
1694852 E1380, 13HP Snowthrower (
Resumen del contenido incluido en la página 2
Resumen del contenido incluido en la página 3
Table Of Contents PRODUCT COMPONENTS PAGES Handles and Controls Group - Channel .............................................................................................................. 4 Handles and Controls Group ............................................................................................................................... 8 Engine and Frame Group ...............................................................................................................................
Resumen del contenido incluido en la página 4
Handles and Controls Group - Channel 987044 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 11 10 12 2 1 Linkage adjustment for traction and auger drive with power boost: with 8 drive levers engaged, the bottom end of 9 lower rods (Ref. 40 & 66) should be flush with bottom of springs (Ref. 39 & 68). 4 5 13 7 14 6 3 15 17 16 18 19 69 71 72 20 4 4 12 22 9 6 23 4 24 64 4 5 56 12 21 66 70 69 68 28 25 37 38 26 29 30 39 31 67 35 65 Shift rod assembly 27 27 (Ref. 7
Resumen del contenido incluido en la página 5
Handles and Controls Group - Channel REF NO PART NO. QTY. DESCRIPTION 1 1727128 1 HANDLE, Clutch R.H. 2 1668608 2 GRIP, Handle Clutch, Black 3 1928732 1 CAPSCREW, Hex Washer Head Taptite #10-24 x 1 4 1729104 5 BUSHING, 1/2 ID x 3/4 OD x 1/4, Plastic 5 1725205A 2 LEVER & TUBE ASSEMBLY, Clutch 6 1960471 4 CAPSCREW, Hex Washer Head Taptite #12-24 x 1 7 1705899 1 GUIDE, Control 8 1726317 2 GRIP, Black Soft 1 in. (24 in. & 28 in. Models Only) 9 1723965 2 HAND GRIP, Heated 1 in. (32 & 38 in. Models On
Resumen del contenido incluido en la página 6
Handles and Controls Group - Channel 987044 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 11 10 12 2 1 Linkage adjustment for traction and auger drive with power boost: with 8 drive levers engaged, the bottom end of 9 lower rods (Ref. 40 & 66) should be flush with bottom of springs (Ref. 39 & 68). 4 5 13 7 14 6 3 15 17 16 18 19 69 71 72 20 4 4 12 22 9 6 23 4 24 64 4 5 56 12 21 66 70 69 68 28 25 37 38 26 29 30 39 31 67 35 65 Shift rod assembly 27 27 (Ref. 7
Resumen del contenido incluido en la página 7
Handles and Controls Group - Channel REF NO PART NO. QTY. DESCRIPTION 45 1960518 2 NUT, Push for 1/4 Diameter Thread 46 1960252 2 CARRIAGE BOLT, 1/4-20 x 5/8 G5 (Used on all models Except 38 in. Models) 47 1960294 2 NUT, Hex Flange Whiz Lock, 1/4-20 Small (Used on all models Except 38 in. Models) 48 1725283 1 ROD, Chute Worm, 18 Long (Used on all models Except 38 in. Models) 49 1668186 1 WORM, Chute, L.H. (Used on all models Except 38 in. Models) 50 1611911 1 SUPPORT, Worm (Used on all models Ex
Resumen del contenido incluido en la página 8
Handles and Controls Group 987161 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 7 8 Apply adhesive to 12 secure grips. 9 11 15 10 5 Must slide freely in 22 dash assembly (Ref 18). 16 6 Apply lubricant as required. 17 14 23 13 21 3 20 24 Insert shift rod (Ref. 65) 4 19 into outter hole of Ref. 68. 18 69 2 67 68 70 58 26 35 71 60 25 1 11 61 27 66 28 67 65 62 72 60 61 64 33 30 16 29 63 31 34 32 Shift rod assembly (Ref. 66) 61 52 must pivot freely on pivot blo
Resumen del contenido incluido en la página 9
Handles and Controls Group REF NO PART NO. QTY. DESCRIPTION 1 1726833 1 CABLE AND SPRING ASSEMBLY, R.H. Auger 2 1731334A 1 HANDLE, Tube, R.H. 3 1922127 1 CAPSCREW, Hex Head, 5/16-18 x 1-3/4 G5 4 1921221 3 CAPSCREW, Hex Head, 5/16-18 x 1-1/2 G5 5 1960671 2 SCREW, Pan Head Torx, 1/4-20 x 3/4, Thread Cutting 6 1715654 2 SPACER, 1/4ID x 25/64OD x 11/64LG 7 1922837 2 CAPSCREW, Hex Head, 1/4-20 x 1-1/2 G5 8 1722638 1 HANDLE, Clutch R.H. 9 1715655 2 SPACER 10 1923358 2 NUT, Hex Centerlock, 1/4-20 11 17
Resumen del contenido incluido en la página 10
Handles and Controls Group 987161 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 7 8 Apply adhesive to 12 secure grips. 9 11 15 10 5 Must slide freely in 22 dash assembly (Ref 18). 16 6 Apply lubricant as required. 17 14 23 13 21 3 20 24 Insert shift rod (Ref. 65) 4 19 into outter hole of Ref. 68. 18 69 2 67 68 70 58 26 35 71 60 25 1 11 61 27 66 28 67 65 62 72 60 61 64 33 30 16 29 63 31 34 32 Shift rod assembly (Ref. 66) 61 52 must pivot freely on pivot blo
Resumen del contenido incluido en la página 11
Handles and Controls Group REF NO PART NO. QTY. DESCRIPTION 45 1727088 1 ROD, 3/8" Diameter, 26"LG, E-Coat 46 1718793 1 SUPPORT, Gear 47 1960518 2 NUT, Push for 1/4 Diameter Thread 48 1960252 2 CARRIAGE BOLT, 1/4-20 x 5/8 G5 49 1960294 2 NUT, Hex Flange, 1/4-20, Whiz Lock Small 50 1611911 1 SUPPORT, Worm 51 1931333 1 CARRIAGE BOLT, 5/16-18 x 3/4 G5 52 1960684 2 NUT, Hex Keps, 5/16-18, Conical Washer 53 2816168 2 PIN, Spring 1/8 x 3/4 54 1668186 1 WORM, Chute, L.H. 55 1725283 1 ROD, 3/8" Diameter
Resumen del contenido incluido en la página 12
Engine and Frame Group 987035 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 15 Position idler pulley (Ref. 12) 19 9 at center of slot in clutch arm (Ref. 10). 17 12 13 Hook one end of spring (Ref. 14) 18 over clutch rod assembly (Ref. 10) 16 between tabs and other end onto the tube handle capscrew (Ref. 20). 20 11 21 22 23 14 8 10 24 25 Long hub of idler pulley (Ref. 3) to be toward idler arm (Ref. 6). 1 4 3 27 26 8 25 30 14 7 31 2 6 29 5 32 33 28 Hook one
Resumen del contenido incluido en la página 13
Engine and Frame Group REF NO PART NO. QTY. DESCRIPTION 1 1700415 1 MV-BELT, 3L 2 1928731 1 NUT, Hex, Toplock, Jam, 3/8-16 3 1668477 4 PULLEY, Idler 4 1960647 1 SCREW, Hex Head, 3/8-16 x 1-1/2 5 1665994 1 PIN, Flat Head Drilled 6 1703046A 1 ARM, Idler, 5-3/4 LG 7 1727149 1 SPRING, Extension 8 1722460 2 PIN, Quick 9 1701257 1 V-BELT, HA 10 1729646A 1 ROD AND ARM ASSEMBLY, Clutch, Brake 11 1928352 1 NUT, Hex Flange, 3/8-16 Whiz Lock Large 12 1726348 1 PULLEY, Idler 13 2860709 1 CAPSCREW, Hex Whiz
Resumen del contenido incluido en la página 14
Engine and Frame Group 987035 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 15 Position idler pulley (Ref. 12) 19 9 at center of slot in clutch arm (Ref. 10). 17 12 13 Hook one end of spring (Ref. 14) 18 over clutch rod assembly (Ref. 10) 16 between tabs and other end onto the tube handle capscrew (Ref. 20). 20 11 21 22 23 14 8 10 24 25 Long hub of idler pulley (Ref. 3) to be toward idler arm (Ref. 6). 1 4 3 27 26 8 25 30 14 7 31 2 6 29 5 32 33 28 Hook one
Resumen del contenido incluido en la página 15
Engine and Frame Group REF NO PART NO. QTY. DESCRIPTION 44 1921515 2 CAPSCREW, Hex Head, 5/16-24 x 3/4 G5 45 1922128 1 CAPSCREW, Hex Head, 3/8-24 x 1-1/2 G8 46 1916965 1 LOCKWASHER, Spring, 3/8 47 1922755 1 WASHER, 3/8 48 1726867 1 PULLEY, Engine Outside, Powdered Metal 49 1726866 1 PULLEY, Engine Middle, Powdered Metal 50 1726865 1 PULLEY, Half Powdered Metal Footnotes * See your local Briggs & Stratton distributor for Parts & Service. The above parts group applies to the following Mfg. Nos.: 1
Resumen del contenido incluido en la página 16
Engine and Frame Group with Power Boost 987038 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 15 Position idler pulley (Ref. 12) 19 9 at center of slot in clutch arm (Ref. 10). 17 Hook one end of spring (Ref. 14) 12 13 18 over clutch rod assembly (Ref. 10) 16 between tabs and other end into slot in frame. 20 11 21 22 23 24 14 8 10 25 Long hub of idler 21 34 pulley (Ref. 3) to be toward idler arm (Ref. 6). 1 4 3 33 28 26 8 32 14 27 14 31 7 35 2 6 30 5 36 37
Resumen del contenido incluido en la página 17
Engine and Frame Group with Power Boost REF NO PART NO. QTY. DESCRIPTION 1 1700415 1 V-BELT, 3L 1 1672732 1 V-BELT, 3L (Used Only on 38 in. Models) 2 1928731 1 NUT, Hex, Toplock, Jam, 3/8-16 3 1668477 1 PULLEY, Idler 4 1960647 1 CAPSCREW, Hex Head, 3/8-16 x 1-1/2 5 1665994 1 PIN, Flat Head Drilled 6 1703046A 2 ARM, Idler, 5-3/4 LG 7 1727149 1 SPRING, Extension 8 1722460 1 PIN, Quick 9 1676460 1 V-BELT, HA 9 1666655 1 V-BELT, HA (Used Only on 38 in. Models) 10 1729646A 1 ROD AND ARM ASSEMBLY, Clu
Resumen del contenido incluido en la página 18
Engine and Frame Group with Power Boost 987038 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 15 Position idler pulley (Ref. 12) 19 9 at center of slot in clutch arm (Ref. 10). 17 Hook one end of spring (Ref. 14) 12 13 18 over clutch rod assembly (Ref. 10) 16 between tabs and other end into slot in frame. 20 11 21 22 23 24 14 8 10 25 Long hub of idler 21 34 pulley (Ref. 3) to be toward idler arm (Ref. 6). 1 4 3 33 28 26 8 32 14 27 14 31 7 35 2 6 30 5 36 37
Resumen del contenido incluido en la página 19
Engine and Frame Group with Power Boost REF NO PART NO. QTY. DESCRIPTION 38 1726942 1 HOSE, Oil Drain, w/Fittings 39 1727033 1 CAPSCREW, Muffler Deflector 40 1727032 1 DEFLECTOR, Rain Guard, B&S Snow Muffler 41 2831277 4 NUT, Hex Flange, 5/16-18, Whiz Lock Small 42 1725326A 4 SUPPORT, Engine Riser (Used on all models Except 38 in. Models) 43 1935159 3 CAPSCREW, Hex Whiz Lock Flange, 5/16-18 x 2-1/4 (Used on all models Except 38 in. Models) 43 1921221 3 CAPSCREW, Hex Head, 5/16-18 x 1-1/2 G5 (Us
Resumen del contenido incluido en la página 20
Auger and Impeller Group 985466R1 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. End of hub to be flush with end of rolled down 35 shaft (Ref. 9). 1 4 2 34 Torque to 30 -34 ft-lbs. 40 - 46 Nm. 36 15 5 10 7 6 2 16 14 10 Torque to 17 18-21 ft-lbs. 3 10 15 24 - 28 Nm. 8 9 11 18 12 19 Impeller to be positioned Marked side of worm 13 against bearing before gear must contact against 6 tightening set screw. left thrust washer to assure proper gear mesh. 21 20 22 3
