Resumen del contenido incluido en la página 1
1 12527SB 2527SB
Operator's Manual
Resumen del contenido incluido en la página 2
IMPORTANT Safe Operation Practices for Walk-Behind Snow Throwers This snow thrower is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury. WARNING: Snow throwers have ex- Look for this symbol to point out im- posed rotating parts, which can cause por tant safety precautions. It means severe injury from contact, or from ma- CAUTION!!! BE COME ALERT!!! YOUR terial thrown from the discharge chute. SA
Resumen del contenido incluido en la página 3
6. When cleaning, repairing or inspecting the snow thrower, Clearing a Clogged Discharge Chute stop the engine and make certain the collector/impel- Hand contact with the rotating impeller inside the discharge ler and all moving parts have stopped. Disconnect chute is the most common cause of injury associated with the spark plug wire and keep the wire away from the snow throwers. Never use your hand to clean out the dis- plug to prevent someone from accidentally starting the charge chute.
Resumen del contenido incluido en la página 4
PARTS PACKED SEPARATELY IN CARTON (1) POWER CORD (1) MULTI- (3) RETAINER (198563) WRENCH SPRINGS (180684) (169675) (2) LOCKNUTS (2) SHEAR BOLTS 1/4-20 x 1-3/4 1/4-20 (192090) (73800400) (2) FLAT WASHERS SAFTEY IGNITION KEY (S) (422663) (2) CARRIAGE BOLTS (1) LOCKNUT (1) CARRIAGE BOLT 3/8-16 x 2.25 5/16-18 5/16-18 x 5/8 (751153) (72250505) (1) LOCKNUT (1) SHOULDER (1) WASHER 3/8 (1) LOCKNUT 3/8 1/4-20 BOLT 1/4-20 (1) SPRING (2) HANDLE KNOBS (191730) (179829) (184505) (19131316) (73800600) AS
Resumen del contenido incluido en la página 5
ASSEMBLY / PRE-OPERATION INSTALL TRACTION DRIVE CONTROL ROD HOW TO SET UP YOUR SNOW THROWER (See Figs. 3 and 4) TOOL BOX (See Fig. 10) A toolbox is provided on your snow thrower. The toolbox is The traction drive control rod is installed on the snow located on top of the belt cover. Store the extra shear bolts, thrower. nuts and multi-wrench provided in parts bag in the toolbox. 1. Remove plastic tie securing rod to lower handle. NOTE: The multi-wrench may be used for assembly of the 2. With
Resumen del contenido incluido en la página 6
ASSEMBLY / PRE-OPERATION INSTALL DISCHARGE CHUTE / CHUTE ROTATER INSTALL AUGER CONTROL ROD (See Figs. 5 and 6) HEAD (See Fig. 7) 1. Retrieve vinyl sleeve and spring from bag of parts and retrieve the auger control rod from carton chute tray. NOTE: The multi-wrench provided in your parts bag may Slide straight rod end through the small hole in the be used to install the chute rotater head. vinyl sleeve. Hook spring in hole in rod end. 1. Place discharge chute assembly on top of chute base
Resumen del contenido incluido en la página 7
ASSEMBLY / PRE-OPERATION INSTALL CHUTE DEFLECTOR REMOTE CONTROL (See Figs. 8 and 9) 1. Install remote cable bracket to discharge chute with 5/16-18 carriage bolt and 5/16-18 locknut as shown. Tighten securely. 2. Install remote cable eyelet to chute deflector with 1/4-20 shoulder bolt and 1/4-20 locknut as shown. Tighten nut securely. Cable eyelet will be loose on shoulder bolt. 3. Install spring hooks between hex nuts on chute rotater head and into hole in chute deflector as shown. SPRIN
Resumen del contenido incluido en la página 8
OPERATION KNOW YOUR SNOW THROWER READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. These symbols may appear on your snow thrower or in literature supplied with the product. Learn and understand their meaning. PRIMER DANGER OR WARNING READ AND FOLLOW ALL SAFETY INFORMATION AND INSTRUCTIONS BEFOR
Resumen del contenido incluido en la página 9
OPERATION MUF FLER ELECTRIC AUGER DISCHARGE CHUTE CONTROL LEVER START CONTROL BUTTON LEVER DEFLECTOR REMOTE GAS O LINE DRIVE SPEED FILLER CAP CONTROL LEVER CON TROL LEVER POWER CORD PLUG CHOKE CHUTE CON- DE FLEC TOR TROL TRACTION DRIVE SAFETY CONTROL IGNITION LEVER KEY LH TURN TRIGGER ON / OFF SWITCH DISCHARGE PRIM ER CHUTE LIGHT FUEL SHUT-OFF VALVE RECOIL (AUXILIARY) STARTER HANDLE HANDLE CLEAN-OUT TOOL KNOB MUF FLER NOTE: ITEMS ABOVE ARE SHOWN IN THEIR TYPICAL TOOLBOX LOCATI
Resumen del contenido incluido en la página 10
OPERATION The operation of any snow thrower can result TO CONTROL SNOW DISCHARGE (See Fig. 13) in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear WARNING: Snow throwers have ex- safety glasses or eye shields while operating posed rotating parts, which can cause your snow thrower or performing any ad just- severe injury from contact, or from ma- ments or repairs. W e recommend standard safe ty glasses terial thrown from the discharge chute. or a
Resumen del contenido incluido en la página 11
OPERATION • Release traction drive control lever to stop the forward AUGER or reverse movement of the snow thrower. CONTROL SPEED and DIRECTION are controlled by the drive speed LEVER control lever. • Press downward on the speed control lever and move lever to de sired po si tion BE FORE engaging the trac- tion drive control lever . Be sure lever springs back and locks into desired position. CAUTION: Do not move speed con trol le ver when traction drive control lever is en gaged. Damage
Resumen del contenido incluido en la página 12
OPERATION TO ADJUST SKID PLATES (See Fig. 18) BEFORE STARTING THE ENGINE NOTE: The wrench provided in your parts bag may be CHECK ENGINE OIL LEVEL (See Fig. 19) used to adjust the skid plates. The engine on your snow thrower has been shipped from Skid plates are located on each side of the auger housing the factory already filled with oil. and adjust the clearance between the scraper bar and the 1. Check engine oil with snow thrower on level ground. ground surface. Adjust skid plates evenly
Resumen del contenido incluido en la página 13
OPERATION TO START ENGINE SNOW THROWING TIPS • Be sure fuel shut-off valve is in the “OPEN” position. • Go slower in deep, freezing or heavy wet snow. Use the drive speed control, NOT the ON / OFF switch, to Your snow thrower engine is equipped with a recoil starter. adjust speed. COLD START • It is easier and more efficient to remove snow im me- 1. Insert safety ignition key (tied to recoil start cord) into di ate ly after it falls. ignition slot until it clicks. DO NOT turn the key. K
Resumen del contenido incluido en la página 14
MAINTENANCE GENERAL REC OM MEN DA TIONS LUBRICATION CHART The warranty on this snow thrower does not cover items that have been sub ject ed to operator abuse or negligence. ➀ SAE 30 Motor Oil To receive full value from the warranty, operator must maintain snow thrower as in struct ed in this manual. Some See “ENGINE” in ➁ ad just ments will need to be made periodically to properly Maintenance section maintain your snow thrower. General ➂ At least once a season, check to see if you should
Resumen del contenido incluido en la página 15
MAINTENANCE BELTS TO CHANGE ENGINE OIL Check belts for deterioration and wear after every 50 hours Determine temperature range anticipated before next oil of operation and replace if necessary. The belts are not change. All oil must meet API service classification SG–SL. ad just able. Replace belts if they begin to slip from wear. • Be sure snow thrower is on level surface. (See “TO REMOVE BELT COVER” in the Service and • Oil will drain more freely when warm. Adjustments section of this manu
Resumen del contenido incluido en la página 16
SERVICE AND ADJUSTMENTS 1. Disengage all controls and move throttle control to WARNING: To avoid serious injury, before STOP position. Wait for all moving parts to stop. performing any service or ad just ments: 2. Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come 1. Be sure the on/off switch is in the in contact with spark plug. OFF position. 3. Align holes in impeller hub with holes in impeller shaft 2. Remove safety ignition key. a
Resumen del contenido incluido en la página 17
SERVICE AND ADJUSTMENTS TO REPLACE BELTS (See Fig. 22) 7. RELIEVE TENSION ON TRACTION DRIVE BELT IDLER and remove traction drive belt from around The auger and traction drive belts are not adjustable. If the pulleys. belts are damaged or begin to slip from wear, they should be replaced. It is recommended that the belt(s) be replaced HINT: Insert a 3/8" drive ratchet (in the “ON” position) into by a Sears service center/department. the square hole in idler arm and rotate ratchet clockwise
Resumen del contenido incluido en la página 18
SERVICE AND ADJUSTMENTS ENGINE SPEED TO REMOVE WHEELS (See Fig. 23) Never tamper with the engine governor, which is factory set • Remove the klik pin and remove wheel from axle. for proper engine speed. Overspeeding the engine above IMPORTANT: When installing wheel, be sure to use the the factory high speed setting can be dangerous and will axle hole closest to the end of the shaft – do not use the void the warranty. If you think the engine-governed high hole in the wheel hub (if equipped)
Resumen del contenido incluido en la página 19
STORAGE Immediately prepare your snow thrower for storage at • Empty the fuel tank by starting the engine and letting it run until the fuel lines and car bu re tor are empty. the end of the season or if the unit will not be used for 30 days or more. • Never use engine or carburetor cleaner prod ucts in the fuel tank or permanent damage may occur. WARNING: Never store the snow • Use fresh fuel next season. thrower with gaso line in the tank in side NOTE: Fuel stabilizer is an acceptable alt
Resumen del contenido incluido en la página 20
TROUBLESHOOTING See appropriate section in manual unless directed to an authorized service center/department. PROBLEM CAUSE CORRECTION Does not start 1. Fuel shut-off valve (if so 1. Turn fuel shut-off valve to OPEN position. equipped) in OFF position. 2. Safety ignition key 2. Insert safety ignition key. is not inserted. 3. Out of fuel. 3. Fill fuel tank with fresh, clean gasoline. 4. Throttle in STOP position 4. Move throttle to FAST position (or ON/OFF switch is OFF). (or ON/OFF
