Manual de instrucciones de Wayne SEP6

Resumen del contenido incluido en la página 1

SEP4, SEP5,
Operating Instructions & Parts Manual
SEP6 and SEP8
Please read and save these instructions. Read carefully before attempting to assemble, install, operate or
maintain the product described. Protect yourself and others by observing all safety information. Failure to
comply with instructions could result in personal injury and/or property damage! Retain instructions for future
reference.
Sewer Ejector
Pump
EQUIPMENT PROBLEMS. To help GENERAL SAFETY INFORMATION
Description
reco

Resumen del contenido incluido en la página 2

Operating Instructions and Parts Manual Functionally, the liquid in the basin rises Installation General Information and trips the first float, but the pumps do Always not turn ON. As the liquid level rises, it Sewage Pump Systems: disconnect trips the second float, activating one of the Simplex System the power source before pumps. Once the liquid level recedes and attempting to install, service, A simplex system consists of one pump, no longer trips the second float, the pump rel

Resumen del contenido incluido en la página 3

Operating Instructions and Parts Manual 6. Drill a 1/8 in. hole in the discharge power cords will be brought through Installation (Continued) pipe 1 to 2 inches above the flange. the appropriate openings in the This will prevent air locking and loss basin cover. Do not modify existing INSTALLATION BASICS: of prime at startup. A gate valve openings in any way. 1. NEVER lift this product by the should be installed in the system All sewage basins electrical cords. after the check valve.

Resumen del contenido incluido en la página 4

Operating Instructions and Parts Manual 2. Disassembly of the motor prior to Operation (Continued) Maintenance expiration of warranty will void the Always disconnect warranty. If repairs are required, see 2. With the cover removed, add water the electrical troubleshooting chart. to the basin and observe the float supply before attempting to install, 3. Inlet should be kept clean and free control switch operation. service, relocate or perform any of all foreign objects and inspect 3

Resumen del contenido incluido en la página 5

Operating Instructions and Parts Manual Troubleshooting Chart Symptom Possible Cause(s) Corrective Action Pump will not start or run 1. Blown fuse, tripped breaker 1. If blown, replace with proper sized fuse or reset breaker 2. Low line voltage 2. If voltage is under 108 volts, check wiring size 3. Defective motor 3. Replace pump 4. Defective float switch 4. Replace float switch 5. Stuck/ jammed impeller 5. If impeller will not turn, remove housing and remove blockage 6. Float obstructed 6. Mak

Resumen del contenido incluido en la página 6

Operating Instructions and Parts Manual For Replacement Parts or Technical Assistance, Call 1-800-237-0987 Please provide following information: Address any correspondence to: - Model number Wayne Water Systems - Serial number (if any) 101 Production Drive - Part description and number as shown in parts list Harrison, OH 45030 U.S.A. 1 2 3 4 5 6 22 7 8 21 9 20 19 18 17 10 16 15 14 13 12 11 Ref. Ref. No. Description Part Number Qty No. Description Part Number Qty 1 Pipe plug 1/4 in. NPT

Resumen del contenido incluido en la página 7

Operating Instructions and Parts Manual Notes www.waynepumps.com 7

Resumen del contenido incluido en la página 8

Operating Instructions and Parts Manual Limited Warranty For one (1) year from the date of purchase, Wayne Water Systems will repair or replace, at its option, for the original purchaser any part or parts of its Sump Pumps or Water Pumps (“Product”) found upon examination by Wayne Water Systems to be defective in materials or workmanship. Please call Wayne Water Systems (1-800-237-0987) for instructions or see your dealer. Be prepared to provide the model number and serial number when exer