Manual de instrucciones de Ultra Start MCS-100

Resumen del contenido incluido en la página 1

Installation Manual


MCS-100 Remote Control Motorcycle Alarm






!

!
"
#$%


    

  

Resumen del contenido incluido en la página 2

MCS-100 SECTION 1: SYSTEM LAYOUT Light Output (+20 Amp) White Park or Signal Light (Diag. #4) 8 7 8 Red 15 Amp Fuse +12V DC Power 7 6 White Light Output (+20 Amp) Park or Signal Light (Diag. #4) 5 6 Connect to Battery Ground 5 Black Ground - Trigger Input (-) 4 Green Tilt Switch or Sensor (Diag. #1) 3 4 Yellow Ignition Input (+) Ignition Wire (Diag. #3) 3 LED Output (+3V) 3V LED (+) Wire (Diag. #2) Brown 2 1 2 Starter Interrupt Output (+) Start Wire (Diag. #3) Orange 1 SECTION 2: SYSTE

Resumen del contenido incluido en la página 3

MCS-100 2. Use 30/40 Amp SPDT relay to connect as shown. Connect the Starter Interrupt output (Orange) wire to pin 86 of the relay. Connect pin 30 of the relay to the Motor side of the Starter wire. Connect pin 87a of the relay to the switch side of the Starter wire. 3. Locate the Ignition wire. 4. Connect the Switched ignition (yellow) wire and 85 of the Starter Interrupt relay to the Ignition wire. To Starter Motor Cut x or Relay 87 87a 86 85 30 Orange Yellow 1 3 Diagram

Resumen del contenido incluido en la página 4

MCS-100 SECTION 3: SYSTEM OPERATION The MCS-100 is very sophisticated, but the operation is simple. Your two button RF transmitter is easy to use for arm, disarm, personal protection, and programming the system for many custom functions. 3.1 Remote System Arm (On)
Press and release RF transmitter button #1.
One siren chirp sound and a light flash verify the operation.
If you hear four chirp sounds, the MCS-100 has detected a faulty sensor. 3.2 Remote System Disarm (Off)

Resumen del contenido incluido en la página 5

MCS-100 Shock Sensor Disable Turn ignition on. Within 10 seconds, press button #1, #2, 1 1 Shock Sensor Enable (4.6) #3, #1 in succession. (#3=#1+#2) 2 2 Valet Mode On Turn Ignition on. Within 10 seconds, press button #2, #3, 1 1 Valet Mode Off (4.7) #2, #3 in succession. (#3=#1+#2) 2 2 Audible Warning Sound Off Turn Ignition on. Within 10 seconds, press button #1, #3, 1 1 Audible Warning Sound On (4.8) #2, #1 in succession. (#3=#1+ #2) 2 2 Siren Output Tone Selection (4.9) Turn

Resumen del contenido incluido en la página 6

MCS-100 4.4 Emergency Disarm The emergency disarm is activated through the ignition key switch and means that the system can be disarmed without remote. To activate the EMERGENCY DISARM:
While the system is triggered, turn the ignition key on and off four (4) times within ten (10) seconds.
The operation is confirmed with two siren chirp sounds and two parking light flashes. NOTE: In passive mode, if passive armed after disarming by emergency disarm, there is entry delay of

Resumen del contenido incluido en la página 7

MCS-100 4.7 Valet Mode The Valet Mode is activated through the ignition key switch and means that all normal system functions are turned off. This feature is useful when valet parking, refueling, or servicing your motorcycle. To activate the VALET MODE:
Turn the ignition key to the on position.
Within ten (10) seconds PRESS BUTTONS #2, #3, #2, #3 in succession. (#3=#1+#2)
The valet mode is confirmed with one chirp sound and one parking light flash. To deactivate the VALET

Resumen del contenido incluido en la página 8

MCS-100 1. Turn the ignition key to the on position. 2. Within ten (10) seconds PRESS BUTTONS #1, #3, #1, #3 in succession. (#3=#1+#2) 3. The operation is confirmed with one chirp sound and one parking light flash. 4. Press button #1 of your transmitter to increase the shock sensor sensitivity. 5. If you want to increase more than one level of sensitivity, press and hold button #1 of your transmitter. You will hear 1 chirp sound every 1 seconds. At the maximum setting, you will hear