Resumen del contenido incluido en la página 1
Resumen del contenido incluido en la página 2
TABLE OF CONTENTS Content Page Content Page Customer Support 2 Maintenance 17 Safety 3 Off-season Storage 21 Assembly 6 Troubleshooting 22 Features and Controls 10 Parts List 23 Operation 12 Warranty Back Cover FINDING MODEL NUMBER This Operator’s Manual is an important part of your new lawn tractor. It will help you assemble, prepare and maintain the unit for best performance. Please read and understand what it says. Before you start assembling your new equipment, please locate the model plat
Resumen del contenido incluido en la página 3
SECTION 1: SAFETY This machine meets voluntary safety stan- dard B71.8 – 1996, which is sponsored by the Outdoor Power Equipment Institute, Inc., and is published by the American National Standards Institute. Forward Clutch Bail Reverse Clutch Control (Models 634F ⁄634A) WARNING Depth Regulator The engine exhaust from this product contains chemicals known to the State of California to Tine Hood Flap cause cancer, birth defects or other reproduc- Safety Alert Symbol This is a safety alert
Resumen del contenido incluido en la página 4
4. Exercise caution to avoid slipping or fall- If in doubt about the tilling conditions, al- 24. Do not touch engine parts which may ing. ways use the following operating precau- be hot from operation. Let parts cool down tions to assist you in maintaining control sufficiently. 5. If the unit should start to vibrate abnor- of the tiller: mally, stop the engine, disconnect the 25. Please remember: You can always stop a. Walk behind and to one side of the spark plug wire and prevent it from tou
Resumen del contenido incluido en la página 5
Decals Reverse Clutch Control Forward Clutch Bail For your safety and the safety of others, vari- Operating Instruction (Models 634F/634A) ous safety and operational decals are located on your unit (see Figure 1-2). Keep the decals clean and legible at all times. Starting Stabilization Contact your local service dealer or the factory Message (on engine) for replacements if any decals are damaged or missing. Warning Messages Refer to the Parts List pages in this Manual for decal locatio
Resumen del contenido incluido en la página 6
SECTION 2: ASSEMBLY WARNING: To prevent ASSEMBLY STEPS personal injury or property STEP 1: UNPACKING INSTRUCTIONS damage, do not start the engine NOTE: While unpacking, do not severely until all assembly steps are bend any control cables. complete and you have read and understand the safety and 1. The tiller weighs approximately 133 lbs. operating instructions in this Do not attempt to remove it from the ship- manual. ping platform until instructed to do so in 1 1 these Assembly ste
Resumen del contenido incluido en la página 7
Resumen del contenido incluido en la página 8
BRONCO 4. Check for correct tension on the forward drive belt by taking two measurements of the cable spring, as follows: a. With the Forward Clutch Bail (Y, Fig. 2- 6) in an open (released) position, measure the length of the cable spring (W) from the Z outermost coil to the outermost coil. X b. Squeeze the Forward Clutch Bail against the handlebar (see Fig. 2-7) and re-mea- sure the spring length. The belt tension is correct if this second measurement is be- Hold bail against handleba
Resumen del contenido incluido en la página 9
STEP 6: CHECK TRANSMISSION STEP 7: ADD MOTOR OIL STEP 8: CHECK HARDWARE OIL LEVEL The tiller is shipped without oil in the en- Check all nuts and screws for tightness. gine. The transmission was filled with gear oil at STEP 9: CHECK AIR PRESSURE IN the factory. However, you should check the IMPORTANT: Do not start the engine with- TIRES (units with pneumatic tires) gear oil level at this time to make certain it out first adding motor oil. Severe engine Check the air pressure with a ti
Resumen del contenido incluido en la página 10
Resumen del contenido incluido en la página 11
Resumen del contenido incluido en la página 12
SECTION 4: OPERATION 1. Complete the Pre-Start Checklist on WARNING: Before Reverse Clutch Control this page. operating your machine, (Models 634F/634A) carefully read and understand 2. Put the wheels in the WHEEL DRIVE po- all safety (Section 1), controls sition (see Wheel Drive Pins in Section 3 of (Section 3) and operating this manual). instructions (Section 4) in this WARNING: To help Forward Manual, the separate Engine Clutch Bail prevent serious personal injury Owner’s Manua
Resumen del contenido incluido en la página 13
4. For forward motion of the wheels and (b) Swing the handlebar to the left so the tines: right wheel takes a “step” backward. Next (a) Pull Forward Clutch Bail (Fig. 4-1) up swing the handlebar to the right so the left against handlebar. Release bail to stop for- wheel “steps” backward. Repeat as needed. ward motion of wheels and tines. (c) If longer distances need to be covered (b) When tilling, relax and let the wheels in reverse, shut off the engine, then place pull the unit while
Resumen del contenido incluido en la página 14
TILLING TIPS & TECHNIQUES Avoid pushing down on the handlebars in an attempt to force the tiller to dig deeper. Doing Tilling Depths so takes the weight off the powered wheels, causing them to lose traction. Without the wheels helping to hold the tiller back, the tines will attempt to propel the tiller – often causing the tiller WARNING: Before to skip rapidly across the ground. (Sometimes, slight downward pressure on the handlebars tilling, contact your will help get through a particular
Resumen del contenido incluido en la página 15
TILLING TIPS & TECHNIQUES (CON’T) Power Composting Power composting simply means tilling under and burying in the soil all manner of organic WARNING: When power matter such as crop residues, leaves, grass clippings and cover crops. This material will de- composting, do not keep the compose during the non-growing season and add important natural nutrients to the soil. Depth Regulator Lever at a deep setting if the tiller jumps The first place to begin is with crop residues such as leftover
Resumen del contenido incluido en la página 16
TILLING TIPS & TECHNIQUES (CON’T) Terrace Gardening (continued) To create a terrace, start at the top of the slope and work down. Go back and forth across the first row as shown in Fig. 4-10. Each succeeding lower terrace is started by walking below the terrace you’re pre- paring. For added stability of the tiller, always keep the uphill wheel in the soft, new- ly tilled soil. Do not till the last 12" or more of the downhill outside edge of each terrace. This untilled strip helps preve
Resumen del contenido incluido en la página 17
SECTION 5: MAINTENANCE If a cover is leaking, check for loose WARNING: Before TILLER LUBRICATION screws. If the screws are tight, a new inspecting, cleaning or servicing After every 10 operating hours, oil or gasket or oil seal may be required. the machine, shut off engine, grease the lubrication points shown in wait for all moving parts to come If the leak is from around a shaft and oil Figure 5-1 and described below. to a complete stop, disconnect seal, the oil seal probably needs
Resumen del contenido incluido en la página 18
WARNING: Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Failure to follow these instructions can result in serious personal injury or property damage. 4. The gear oil level is correct if the gear B. To Drain the Transmission Gear Oil: BOLO TINES oil is approximately halfway up the side of The transmission gear oil does not need to The bolo tines will
Resumen del contenido incluido en la página 19
Resumen del contenido incluido en la página 20
