Resumen del contenido incluido en la página 1
Resumen del contenido incluido en la página 2
15 TABLE OF CONTENTS Table Of Contents/Typical Applications. ................................................................................ 2 Rules For Safe Operation...................................................................................................3-5 A. Precautions On Using Your Cordless Tool ....................................................................... 4 B. Important Safety Instructions For Charger .............................................................
Resumen del contenido incluido en la página 3
RULES FOR SAFE OPERATION The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger. The instructions or warnings they give are not substitutes for proper accident prevention measures. SYMBOL MEANING SAFETY ALERT SYMBOL: Indicates danger, warning, or caution. May be used in conjunction with other symbols or pictog
Resumen del contenido incluido en la página 4
RULES FOR SAFE OPERATION (Continued) when working outdoors. Wear protective hair PRECAUTIONS ON USING YOUR covering to contain long hair and keep it from being CORDLESS TOOL drawn into nearby air vents. This product contains Nickel-Cadmium batteries which 9. ALWAYS WEAR SAFETY GLASSES. Everyday must be disposed of properly. eyeglasses have only impact-resistant lenses; they 1. Be aware that this tool is always in an operating are NOT safety glasses. condition, because it does not have to be plug
Resumen del contenido incluido en la página 5
RULES FOR SAFE OPERATION (Continued) 5. To reduce risk of damage to electric plug and cord, use it on any other voltage. pull by the plug rather than the cord when 4. Consecutive charging may cause overheating. If disconnecting charger. you need to recharge batteries consecutively, 6. Make sure cord is located so that it will not be wait for about 15 minutes to allow charger to cool. stepped on, tripped over, or otherwise subjected 5. Do not insert foreign matter into the hole for the to damage
Resumen del contenido incluido en la página 6
SPECIFICATIONS: DRILL-DRIVER R10511 R10521 R10531 Chuck 3/8 in. Keyless 3/8 in. Keyless 1/2 in. Keyless Motor DC Motor 12.0 V DC Motor 14.4 V DC Motor 18.0 V Gear Train Two Speed Two Speed Two Speed Switch Variable Speed Variable Speed Variable Speed No Load Speed 0-400 RPM (Low) 0-400 RPM (Low) 0-400 RPM (Low) 0-1400 RPM (High) 0-1400 RPM (High) 0-1400 RPM (High) Clutch 24 Positions 24 Positions 24 Positions Maximum Torque 250 in./lbs 350 in./lbs 400 in./lbs CHARGER 1400666/1400677 14
Resumen del contenido incluido en la página 7
Resumen del contenido incluido en la página 8
OPERATION LED FUNCTION OF CHARGER 1400677 LED WILL BE LIGHTED TO INDICATE STATUS OF CHARGER AND BATTERY PACK: Red LED Lighted = Fast Charging Mode. Green LED Lighted = Fully Charged Or In Slow Charging Mode To Maintain Battery Pack Charge. Red LED Flashing = Hot or Deeply Discharged Battery Pack. Also Defective Battery Pack After 1 hour. Yellow LED Lighted and Red LED Flashing = Defective Battery Pack. CHARGING WITH CHARGER 1400666, 1400656, OR 1400667 See Figure 3. Normally, the yello
Resumen del contenido incluido en la página 9
OPERATION DIRECTION OF WARNING: ROTATION SELECTOR REVERSE If any parts are missing, do not operate tool until the SWITCH missing parts are replaced. Failure to do so could result TRIGGER in possible serious personal injury. SWITCH See Figure 4. Your drill starts and stops by depressing and releasing the switch trigger. Release the switch trigger to turn drill OFF. VARIABLE SPEED CENTER POSITION (LOCK) See Figure 4. FORWARD Your drill has a variable speed feature in the switch. The switch deliver
Resumen del contenido incluido en la página 10
Resumen del contenido incluido en la página 11
Resumen del contenido incluido en la página 12
OPERATION TORQUE TO DECREASE WARNING: ADJUSTMENT RING TORQUE Be prepared for binding or breakthrough. When these situations occur, the drill has a tendency to grab and kick in the opposite direction, and could cause loss of control ✒ when breaking through material. If you are not prepared, this loss of control can result in possible serious injury. When drilling metals, use a light oil on the drill bit to keep it from overheating. The oil will prolong the life of the bit and increase the drillin
Resumen del contenido incluido en la página 13
1 . 8 E 0 L 0 . C 8 MAINTENANCE DO NOT ABUSE POWER TOOLS. Abusive practices can damage the tool, as well as the workpiece. WARNING: When servicing use only identical Ryobi replacement WARNING: parts. Use of any other parts may create a hazard or cause product damage. Do not attempt to modify this tool or create accessories not recommended for use with this tool. Any such Avoid using solvents when cleaning plastic parts. Most alteration or modification is misuse and could result in a plastics are
Resumen del contenido incluido en la página 14
