Manual de instrucciones de Porter-Cable PTD381

Resumen del contenido incluido en la página 1

ESPAÑOL: PÁGINA 9
Instruction manual
FRANÇAIS: PAGE 17
Manual de
Instrucciones
3/8" Drill
Manuel d'instructions Taladro de 3/8"
Perceuse de 3/8 po
MODEL
PTD381
MODELO
PTD381
MODÈLE PTD381
To learn more about Porter-Cable visit
our website at:
http://www.porter-cable.com
IMPORTANT
Para obtener más información sobre
Please make certain that the person who is
Porter-Cable, visite nuestro sitio web en:
to use this equipment carefully reads and
http://www.porter-cable.com
understands these ins

Resumen del contenido incluido en la página 2

SAFETY GUIDELINES - DEFINITIONS This manual contains indicates an imminently hazardous situation which, if not information that is avoided, will result in death or serious injury. important for you to know and indicates a potentially hazardous situation which, if not understand. This information re- avoided, could result in death or serious injury. lates to protecting YOUR SAFE- TY and PREVENTING indicates a potentially hazardous situation which, if not EQUIPMENT PROBLEMS. To avoided,may resu

Resumen del contenido incluido en la página 3

HAZARD RISK OF LOSS OF HEARING WHAT COULD HAPPEN HOW TO PREVENT IT  Long term exposure to noise produced from the opera-  Always wear ANSI S3.19 hearing protection. tion of air tools can lead to permanent hearing loss. HAZARD RISK TO BREATHING INHALATION HAZARD WHAT COULD HAPPEN HOW TO PREVENT IT  Abrasive tools, such as grinders, sanders, and cut-off  Always wear MSHA/NIOSH approved, properly fitting tools generate dust and abrasive materials which can face mask or respirator when using suc

Resumen del contenido incluido en la página 4

HAZARD RISK OF INJURY (continued) WHAT COULD HAPPEN HOW TO PREVENT IT  Improperly maintained tools and accessories can cause  Maintain the tool with care. serious injury.  Keep a cutting tool sharp and clean. A properly maintained tool, with sharp cutting edges reduces the risk of binding and is easier to control.  There is a risk of bursting if the tool is damaged.  Check for misalignment or binding of moving parts, breakage of parts, and any other condition that affects the tool’s operati

Resumen del contenido incluido en la página 5

SPECIFICATIONS Free Speed (No Load) 1800 RPM Max. Maximum Working Pressure 90 PSI Air Inlet 1/4" NPT Recommended Hose Size 3/8" I.D. Keyless Chuck 3/8” Air Consumption @ 90 PSI 4.5 SCFM ASSEMBLY Accessories Required IMPORTANT: Line pressure or hose inside diameter should be increased to compensate for unusually long air hoses (over 25 feet). Minimum hose diameter should be 3/8” I.D. and fittings should have 1/4” NPT thread. OPERATION Before each use:
Drain water from air compressor tank and c

Resumen del contenido incluido en la página 6

Position drill bit at the point to be drilled and depress the trigger.
Always disconnect air supply when changing drill bits.
Release trigger to stop tool.
When job is complete, turn the air compressor off and store as described in the air compressor operator manual. Tips
Locate the position of the hole to be drilled. Mark that position with a center punch. This provides a good seat for the drill bit point and keeps the drill from moving from the mark. Never apply a spinning drill bit

Resumen del contenido incluido en la página 7

REPAIR PARTS 42 43 44 28 40 22 39 38 36 24 (5) 35 3 34 Ref No. Part No. Description Qty 3 u Spindle 1 22 u Pin 1 24 u Blade 5 28 u Motor Gasket 1 34 + Throttle Valve Plug 1 35 + O-Ring 1 36 + Reverse Retainer 1 38 + Spring 1 39 + O-Ring 1 40 + Valve Stem 1 42 + Spring Pin 1 43 + Throttle Lever 1 44 u Gasket 1 + Only available in Trigger Repair Kit D25305 u Only available in Tune-up Kit D26761 NOTE: Parts not listed are not serviceable. 7- ENG


Resumen del contenido incluido en la página 8

LIMITED WARRANTY PORTER-CABLE CORPORATION warrants to the original purchaser that all products covered under this warranty are free from defects in material and workmanship. Products covered under this warranty include air compressors, air tools, service parts, pressure washers, and generators, which have the following warranty periods: 3 YEARS - Limited warranty on 2-stage oil-free air compressor pumps that operate at 1725 RPM. 2 YEARS - Limited warranty on oil-lubricated air compressor pumps.