Resumen del contenido incluido en la página 1
®
IntelliFlo 4 160 and 100
Variable Speed Programmable Pump
™ ™
(Compatible with IntelliTouch , EasyTouch and IntelliComm)
Installation and
User’s Guide
IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL INSTRUCTIONS
SAVE THESE INSTRUCTIONS
Resumen del contenido incluido en la página 2
Customer Support Sanford, North Carolina (8 A.M. to 5 P.M.) Phone: (800) 831-7133 Moorpark, California (8 A.M. to 5 P.M.) Phone: (800) 831-7133 (Ext. 6312) Fax (800) 284-4151 Web sites: visit www.pentairpool.com and staritepool.com © 2006 Pentair Water Pool and Spa, Inc. All rights reserved This document is subject to change without notice 1620 Hawkins Ave., Sanford, NC 27330 � (919) 566-8000 10951 West Los Angeles Ave., Moorpark, CA 93021 � (805) 553-5000 Trademarks and disclaimers: EasyTouch,
Resumen del contenido incluido en la página 3
i Contents Important Safety Precautions ........................................................................................... ii Section 1: IntelliFlo Overview ........................................................................................... 1 IntelliFlo 4 Variable Speed Pump .......................................................................................... 1 IntelliFlo 4 models ..............................................................................................
Resumen del contenido incluido en la página 4
ii IMPORTANT SAFETY PRECAUTIONS Important Notice: Attention Installer: This manual contains important information about the installation, operation and safe use of this product. This information should be given to the owner and/or operator of this equipment. WARNING — Before installing this product, read and follow all warning notices and instructions which are included. Failure to follow safety warnings and instructions can result in severe injury, death, or property damage. Call (800) 831-
Resumen del contenido incluido en la página 5
iii IMPORTANT SAFETY PRECAUTIONS (continued) WARNING — Water temperature in excess of 100° Fahrenheit may be hazardous to your health. Prolonged immersion in hot water may induce hyperthermia. Hyperthermia occurs when the internal temperature of the body reaches a level several degrees above normal body temperature of 98.6° F. (37° C.). The symptoms of hyperthermia include: drowsiness, lethargy, dizziness, fainting, and an increase in the internal temperature of the body. The effects of hypert
Resumen del contenido incluido en la página 6
iv IMPORTANT SAFETY PRECAUTIONS (continued) General Installation Information WARNING — Pumps improperly sized or installed or used in applications other than for which the pump was intended can result in severe personal injury or death. These risks may include but not be limited to electric shock, fire, flooding, suction entrapment or severe injury or property damage caused by a structural failure of the pump or other system component. WARNING — The pump can produce high levels of suction with
Resumen del contenido incluido en la página 7
1 Section 1 Overview IntelliFlo 4 Variable Speed Pump The IntelliFlo 4 variable speed pump is well suited for all of your pool, spa, cleaner, waterfall and other water application. Using the control panel, IntelliFlo can use one of the four selectable preset speeds or the pump speed can be adjusted to run at a specific speed. IntelliFlo out performs all conventional pumps in its class. Advanced energy conservation features ensure that your filtration system is operating at peak efficiency. Intel
Resumen del contenido incluido en la página 8
2 Features � Adjusts to various pool sizes � Prevents thermal overload � Detects and prevents damage from under and over voltage conditions � Protects against freezing � Communicates with a Pentair IntelliTouch, EasyTouch and IntelliComm system via a two-wire connection � Easy to use operator control panel � Operator control panel buttons for speed control � Built-in strainer pot and volute � Ultra energy-efficient TEFC Square Flange Motor � Compatibility with most cleaning systems, filters, and
Resumen del contenido incluido en la página 9
3 IntelliFlo 4 Drive Assembly and Control Panel The IntelliFlo drive assembly consists of an operator control panel and the system electronics that drive the motor. The drive microprocessor controls the motor by changing the frequency of the current it receives together with changing the voltage to control the rotational speed. Operator Control Panel, buttons and LEDs ¾” NPT male threaded PVC nipple Three Wire Harness Red (hot), Red (hot), Green (Ground) +/- 20% of 230 Volt IntelliFlo 4 Drive As
Resumen del contenido incluido en la página 10
4 IntelliFlo 4 Operator Control Panel The IntelliFlo 4 operator control panel provides manual speed controls for the pump. There are four preset speed buttons that can be selected. The Up and Down button is used to adjust the pump speed. The selected speed can be saved and assigned to one of the speed buttons. 1 2 5 6 3 4 Controls and LEDs 1 Speed 1, Speed 2, Speed 3, and Speed 4 button/LED: Press one of the speed buttons to select the desired preset pump speed. The pump preset speeds are: Spee
Resumen del contenido incluido en la página 11
5 Section 2 Operating IntelliFlo 4 This section describes how to use the IntelliFlo 4 pump control panel. Setting the pump preset speed IntelliFlo 4 operates using one of the preset speeds. Use the speed buttons to select the preset speeds. To set the pump speed 1. Ensure that the pump is powered on and the green power LED is on. 2. Press the desired speed button (1- 4) for less than three seconds to select the preset pump speed. When the selected speed button is pressed, the LED is on. The pump
Resumen del contenido incluido en la página 12
6 Starting the pump To start the pump 1. Ensure that the pump is powered on and the green power LED is on. 2. Press the Start button (LED on) to start the pump. Note: When the pump is using a modified speed and is powered down, the next time the pump is powered up, the pump will use that same speed. Stopping the pump To stop the pump � Press the Stop button to stop the pump. Note: The pump can automatically restart if the communication cable is connected. Resetting the pump to factory defaults T
Resumen del contenido incluido en la página 13
7 Priming the pump for the first time or after service Before the IntelliFlo 4 pump is started for the first time it must be primed. To prime a pump means filling the pump and suction pipe with water. This process evacuates the air from all the suction lines and the pump. It may take several minutes to prime depending on the depth of water, pipe size and length. It is easier to prime a pump if you allow all the air to escape from the pump and pipes. The water cannot enter unless the air can esca
Resumen del contenido incluido en la página 14
8 Priming the pump for the first time or after service (Continued) Priming the Pump � Release all pressure from filter, pump, and piping system; see the filter owner’s manual. � In a flooded suction system (water source higher than pump), the IntelliFlo 4 pump will prime itself when suction and discharge valves are opened. � If the IntelliFlo 4 pump is not in a flooded suction system, unscrew and remove lid cover; fill the and pump with water. � Do not lubricate the trap cover o-ring. The origi
Resumen del contenido incluido en la página 15
9 External Control with IntelliComm Communication Center The IntelliFlo 4 can be remotely controlled by the Pentair IntelliComm Communication Center using an optional communications cable (P/N 350122). The IntelliComm provides four pairs of input terminal connections. These inputs are actuated by either 15 - 240 VAC or 15 - 100 VDC. Using the device's inputs, the programmed IntelliFlo 4 pump speeds can be controlled. If more than one input is active the highest number will be communicated to
Resumen del contenido incluido en la página 16
10 Connecting IntelliFlo 4 to an EasyTouch System The IntelliFlo 4 can be controlled by an IntelliTouch system via the RS-485 communication cable (PN 350122). In this configuration, IntelliTouch starts, stops and controls the speed of the IntelliFlo pump. When the IntelliTouch does this, it rewrites the IntelliFlo 4 memory, which can take several seconds. This causes a delay from when a command is given on the IntelliTouch control panel until the Intelliflo 4 physically responds. The IntelliFl
Resumen del contenido incluido en la página 17
11 4. Lower down the hinged control panel to access the EasyTouch motherboard. 5. Route the communication cable into the lower plastic grommet, up through the low voltage raceway to the EasyTouch load center motherboard. Control panel motherboard Low voltage Raceway 6. Strip back the cable conductors ¼ inch. Insert the two wires into the screw terminals on the board. Secure the wires with the screws. 7. EasyTouch to IntelliFlo 4 pin configuration: � IntelliFlo: Connect pin 6 (green) to EasyTouc
Resumen del contenido incluido en la página 18
12 9. Close the control panel into its original position and secure it with the two access screws. 10. Install the high voltage cover panel and secure it with the two retaining screws. 11. Close the EasyTouch load center front door. Fasten the two spring latches. 12. Switch the power on to the EasyTouch load center. Control panel access screw Control panel access screw Retaining screw High voltage cover panel EasyTouch Load Center (front view) IntelliFlo 4 Installation and User’s Guide
Resumen del contenido incluido en la página 19
13 Section 3 User Maintenance The following information describes how to service and maintain the IntelliFlo pump. Pump Strainer Basket The strainer, sometimes referred to as the “Hair and Lint Pot,” is in front of the of the pump. Inside there is a basket which must be kept clean of leaves and debris at all times. View the basket through the top see through lid to inspect for leaves and debris. Regardless of the length of time between filter cleaning, it is most important to visually inspect t
Resumen del contenido incluido en la página 20
14 Pump Strainer Basket Service (Continued) 10. Ensure that the lid o-ring is properly placed. Seat the clamp and lid then turn clockwise until the handles are horizontal as shown. 11. Reconnect the communication cable to the pump if required. 12. Switch the power ON at the circuit breaker. Reset the pool time clock to the correct time. WARNING — FILTER OPERATES UNDER HIGH PRESSURE. WHEN ANY PART OF THE CIRCULATING SYSTEM (e.g., LOCK RING, PUMP, FILTER, VALV
