Resumen del contenido incluido en la página 1
1
W415-0484 / A / 07.26.06
W415-0484 / A / 07.23.06
Resumen del contenido incluido en la página 2
WARNINGS & SAFETY PRECAUTIONS WHAT TO DO IF YOU SMELL GAS
Resumen del contenido incluido en la página 3
TABLE of CONTENTS PG 2-5 INTRODUCTION 19-20 FINISHING Warnings and Safety Precautions Door Removal & Installation Warranty Louvre Installation General Instructions Log Placement / Glowing Embers General Information Charcoal Embers Care of Glass & Plated Parts Charcoal Lumps Logo Placement 6 - 13 VENTING Venting Lengths 21 OPTIONAL BLOWER INSTALLATION Air Terminal Locations 22 OPTIONAL FAN INSTALLATION / Typical Vent Installations GD36 THERMOSTATIC SENSOR Special Vent Installations Venting Specif
Resumen del contenido incluido en la página 4
4 NAPOLEON NAPOLEON NAPOLEON NAPOLEON NAPOLEON gas fireplaces are manufactured under the strict Standard of the world recog- gas fireplaces are manufactured under the strict Standard of the world recog- gas fireplaces are manufactured under the strict Standard of the world recog- gas fireplaces are manufactured under the strict Standard of the world recog- gas fireplaces are manufactured under the strict Standard of the world recog- nized nized nized nized nized ISO 9001 : 2000 Quality Assurance
Resumen del contenido incluido en la página 5
5 Minimum inlet gas supply pressure is 4.5 inches water col- GENERAL INSTRUCTIONS umn for natural gas and 11 inches water column for propane. THIS GAS FIREPLACE SHOULD BE INSTALLED AND SERV- Maximum inlet gas pressure is 7 inches water column for ICED BY A QUALIFIED INSTALLER to conform with local natural gas and 13 inches water column for propane. Mani- codes. In absence of local codes, install the B36DF to the current fold pressure under flow conditions is 3.5 inches water col- National Fuel
Resumen del contenido incluido en la página 6
6 FIGURE 1 VENTING These vent kits allow for either horizontal or vertical venting For safe and proper operation of the fireplace follow the of the fireplace. FIGURES 3 & 5. The maximum allowable venting instruction exactly. horizontal run is 20 feet. The maximum allowable vertical Deviation from the minimum vertical vent length can vent length is 40 feet. The maximum number of 5" vent create difficulty in burner start-up and/or carboning. connections is two horizontally or three vertically (exc
Resumen del contenido incluido en la página 7
7 AIR TERMINAL LOCATIONS FIGURE 2 INSTALLATIONS CANADIAN U.S.A. A 12 INCHES 12 INCHES Clearance above grade, veranda porch, deck or balcony. Clearance to windows or doors that open. B 12 INCHES 9 INCHES Clearance to permanently closed windows. C 12 INCHES* 12 INCHES* Vertical clearance to ventilated soffit located above the terminal within D 18 INCHES** 18 INCHES** a horizontal distance of 2 feet from the centerline of the terminal. E 12 INCHES** 12 INCHES** Clearance to unventilated soffit. 0 I
Resumen del contenido incluido en la página 8
8 TYPICAL VENT INSTALLATIONS NOTE: When terminating vertically, the restrictor plate W500-0205 must be installed. Refer to Restricting Vertical Vents. FIGURES 3 a-c * When installing with no vertical rise, ensure that the vent pipe does not slope downward. SPECIAL VENT INSTALLATIONS PERISCOPE TERMINATION Use the GD401 periscope kit to locate the air termination above grade. The periscope must be installed so that when final grading is completed, the bottom air slot is located a minimum of 12 inc
Resumen del contenido incluido en la página 9
9 VENTING APPLICATION FLOW CHART HORIZONTAL VERTICAL TERMINATION TERMINATION Vertical rise Vertical rise Vertical rise Vertical rise is less than is less than is equal to or is equal to or horizontal horizontal greater greater run run than the than the horizontal horizontal run run Horizontal Horizontal Horizontal Horizontal run + verti- run + verti- run + verti- run + verti- cal rise to cal rise to cal rise to cal rise to maximum maximum maximum maximum of 40 feet of 24.75 feet of 40 feet of 40
Resumen del contenido incluido en la página 10
10 DEFINITIONS ELBOW VENT LENGTH VALUES for the following symbols used in the venting calcula- feet inches tions and examples are: 1° 0.03 0.5 > - greater than 15° 0.45 6.0 > - equal to or greater than 30° 0.9 11.0 < - less than 45°* * * 1.35 16.0 * * < - equal to or less than 90°* * * * * 2.7 32.0 H - total of both horizontal vent lengths (H ) and off- T R sets (H ) in feet O * * * the first 45º and 90° offset has a zero value and is * * H - combined horizontal vent lengths in feet R show
Resumen del contenido incluido en la página 11
11 HORIZONTAL TERMINATION when (H ) > (V ) Example 2: T T Simple venting configuration (only one 45º and 90° elbow) 90° See graph to determine the re- 90° FIGURE 7 FIGURE 8 quired vertical rise V for the re- H T 4 H quired horizontal run H . 3 T 45° V 2 H 1 H 2 90° V 1 V =4 ft 1 V = 1.5 ft 2 V = V + V = 4 ft + 1.5 ft = 5.5 ft REQUIRED T 1 2 VERTICAL H =2 ft 1 RISE IN H =1 ft 2 INCHES (V ) T H =1 ft 3 H = 1.5 ft 4 H = H + H + H + H = 2 + 1 + 1 + 1. 5 = 5.5 ft R 1 2 3 4 H = .03(one 45º elbow + t
Resumen del contenido incluido en la página 12
12 VERTICAL TERMINATION when (H ) < (V ) Example 3: T T Simple venting configurations V FIGURE 9 2 FIGURE10 90° H 90° 2 V 45° 1 45° H 1 90° See graph to determine the required vertical rise V for the T required horizontal run H . T V =5 ft 1 V = 10 ft 2 V =V + V = 5 + 10 = 15 ft T 1 2 H =3 ft 1 H = 2.5 ft 2 REQUIRED VERTICAL RISE IN H =H + H = 3 + 2.5 = 5.5 ft R 1 2 FEET (V ) T H =.03(one 45º elbow + three 90º elbows - 135º) O = .03(45+90+90+90-135)=5.4 H =H + H = 5.5 + 5.4 = 10.9 ft T R O H +
Resumen del contenido incluido en la página 13
13 VERTICAL TERMINATION when (H ) > (V ) V =1 ft T T 1 Simple venting configurations V = 1.5 ft 2 V =V + V = 1 + 1.5 = 2.5 ft T 1 2 H =6 ft FIGURE 11 1 H =2 ft 2 H = H + H = 6 + 2 = 8 ft R 1 2 H = .03(one 45º elbow + three 90º elbow - 135º) O = .03(45 + 90 + 90 + 90 - 135) = 5.4 ft H =H + H = 8 + 5.4 = 13.4 ft T R O H + V = 13.4 + 2.5 = 15.9 ft T T Formula 1: H < 3V T T 3V = 3 x 2.5 = 7.5 ft T 13.4 > 7.5 Since this formula is not met, this vent configuration is unacceptable. Formula 2: H +
Resumen del contenido incluido en la página 14
14 INSTALLATION WALL AND CEILING PROTECTION FOR SAFE AND PROPER OPERATION OF THE FIREPLACE, VERTICAL INSTALLATION FOLLOW THE VENTING INSTRUCTIONS EXACTLY. NOTE: Only a clearance to combustibles of 2" at the This application occurs top of the vent pipe is required and 1" at the bottom FIGURE 16 when venting through a and sides. roof. Installation kits for various roof pitches are HORIZONTAL INSTALLATION available from your Napo- This application occurs when vent leon dealer. See Accesso- ing thro
Resumen del contenido incluido en la página 15
15 USING FLEXIBLE VENT COMPONENTS Use only approved aluminum flexible liner kits marked: For safe and proper operation of the fireplace, follow the vent- ing instructions exactly. All inner exhaust and outer intake vent pipe joints may be sealed using either Red RTV high temp silicone sealant or Black high temp Mill Pac with the exception of the fireplace "Wolf Steel Approved Venting" as exhaust flue collar which must be sealed using Mill Pac identified by the stamp only on the 8” (not supplied
Resumen del contenido incluido en la página 16
16 5. Remove nails from the shingles, above and to the sides RESTRICTING VERTICAL VENTS of the chimney. Place the flashing over the air terminal and Vertical terminations may display a very active flame. As slide it underneath the sides and upper edge of the this appearance is not desirable, the vent exit must be shingles. Ensure that the air terminal is properly centred restricted using restrictor plate, W500-0205. This reduces within the flashing, giving a 3/4" margin all around. Fasten the v
Resumen del contenido incluido en la página 17
17 B36DF MOBILE HOME INSTALLATION FIGURE 27a-d This appliance may be installed as an OEM (Original Equipment Manufacturer) installation in a manufactured home or mobile home and must be installed in accordance with the manufacturer’s instructions and the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280, in the United States or the Mobile Home Standard, CAN/CSA Z240 MH Series, in Canada. This appliance is only for use with the type(s) of gas indicated on the rating plat
Resumen del contenido incluido en la página 18
18 FIGURES 32a-c NAILING TAB INSTALLATION CORNER 1) Attach the nailing tabs to the corner POST posts using the 2 sheet metal screws supplied. Secure through the centre of NAILING the top and bottom slots in the nailing TAB tab and then through the existing holes in the corner posts. TOP SLOT NAILING If there are no existing holes, follow TAB these instructions: Position the nailing tab so that the front face is offset with the front edge of the corner post (approx. ½"). Centre the nailing ta
Resumen del contenido incluido en la página 19
19 FINISHING DOOR REMOVAL & INSTALLATION L36 LOUVRE INSTALLATION The upper louvres must be removed to allow the door to be Note: The protective wrap is best removed when the opened or closed. To access the lower door latch, open assembly is at room temperature but this can be improved the valve control door. Release the top and bottom door if the assembly is warmed, using a hair dryer or similar latches, located at the right side of the door. source. FIGURE 35 a-c FIGURE 34 A B C A CLIPS FLANGE
Resumen del contenido incluido en la página 20
20 3. Place the bottom of the left crossover log (#4) onto the LOG PLACEMENT locating stud on the left side of the log support. TM PHAZER logs and glowing embers exclusive to Napoleon Fire- The top of the log should rest in the pocket on the rear log. places, provide a unique and realistic glowing effect that is different in every installation. Take the time to carefully po- sition the glowing embers for a maximum glowing effect. Log colours may vary. During the initial use of the fireplace, the
