Resumen del contenido incluido en la página 1
Angle Grinder
150 mm (6”)
MODEL 9566CV
DOUBLE
INSULATION
INSTR U CTION MANU AL
WARNING:
For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
www.makitatools.com
Resumen del contenido incluido en la página 2
SPECIFICATIONS Model 9566CV No load speed (RPM) 4,000 - 9,000/min Overall length 299 mm (11-3/4”) Net weight 1.8 kg (4.0 lbs) Spindle thread 5/8” • Manufacturer reserves the right to change specifications without notice. Specifications may differ from country to country. GENERAL SAFETY RULES USA002-2 (For All Tools) WARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRU
Resumen del contenido incluido en la página 3
5. Avoid body contact with grounded sur- Tool Use and Care faces such as pipes, radiators, ranges and 15. Use clamps or other practical way to refrigerators. There is an increased risk of secure and support the workpiece to a electric shock if your body is grounded. stable platform. Holding the work by hand or 6. Do not expose power tools to rain or wet against your body is unstable and may lead conditions. Water entering a power tool will to loss of control. increase the risk of electric shock.
Resumen del contenido incluido en la página 4
USE PROPER EXTENSION CORD: Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. Table 1 shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the gage num- ber, the heavier the cord. Table 1: Minimum gage for cord V
Resumen del contenido incluido en la página 5
12. Make sure cord is clear of wheel. Do not 17. Do not leave the tool running. Operate the wrap cord around your arm or wrist. If tool only when hand-held. control of tool is lost, cord may become 18. Do not touch the workpiece immediately wrapped around you and cause personal after operation; it may be extremely hot injury. and could burn your skin. 13. Make sure the wheel is not contacting the 19. ALWAYS wear proper apparel including workpiece before the switch is turned on. long sleeve shirt
Resumen del contenido incluido en la página 6
FUNCTIONAL CAUTION: DESCRIPTION • Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. 002978 Shaft lock 1 CAUTION: • Never actuate the shaft lock when the spindle is moving. The tool may be damaged. Press the shaft lock to prevent spindle rotation when install- ing or removing accessories. 1. Shaft lock 001035 Switch action 1 CAUTION: • Before plugging in the tool, always check to see that the slide switch actuates properly and returns t
Resumen del contenido incluido en la página 7
001046 Speed adjusting dial The rotating speed can be changed by turning the speed adjusting dial to a given number setting from 1 to 5. Higher speed is obtained when the dial is turned in the direc- tion of number 5. And lower speed is obtained when it is 2 turned in the direction of number 1. 1 Refer to the table for the relationship between the number settings on the dial and the approximate rotating speed. 1. Speed adjusting dial CAUTION: Number RPM (/min) 1 4,000 • If the tool is operated c
Resumen del contenido incluido en la página 8
002980 Installing or removing wheel guard 1 CAUTION: • When using a depressed center grinding wheel/Multi- 2 disc, flex wheel, wire wheel brush or cut-off wheel, the 3 wheel guard must be fitted on the tool so that the closed 4 side of the guard always points toward the operator. Loosen the lever on the wheel guard. Mount the wheel guard 1. Wheel guard with the protrusion on the wheel guard band aligned with the 2. Bearing box notch on the bearing box. Then rotate the wheel guard 3. Screw 4. Lev
Resumen del contenido incluido en la página 9
001107 Installing or removing abrasive disc (optional 1 accessory) 2 NOTE: 3 • Use sander accessories specified in this manual. These must be purchased separately. Mount the rubber pad onto the spindle. Fit the disc on the rubber pad and screw the lock nut onto the spindle. To 1. Lock nut tighten the lock nut, press the shaft lock firmly so that the 2. Abrasive disc 3. Rubber pad spindle cannot revolve, then use the lock nut wrench and securely tighten clockwise. To remove the disc, follow the
Resumen del contenido incluido en la página 10
CAUTION: • After operation, always switch off the tool and wait until the wheel has come to a complete stop before putting the tool down. Grinding and sanding operation 002983 ALWAYS hold the tool firmly with one hand on housing and the other on the side handle. Turn the tool on and then apply AB the wheel or disc to the workpiece. In general, keep the edge of the wheel or disc at an angle of about 15 degrees to the workpiece surface. During the break-in period with a new wheel, do not work the
Resumen del contenido incluido en la página 11
• ALWAYS use guard with wire wheel brushes, assuring diameter of wheel fits inside guard. Wheel can shatter during use and guard helps to reduce chances of personal injury. Unplug tool and place it upside down allowing easy access to spindle. Remove any accessories on spindle. Thread wire wheel brush onto spindle and tighten with the wrenches. When using wire wheel brush, avoid applying too much pres- sure which causes over bending of wires, leading to prema- ture breakage. MAINTENANCE CAUTION:
Resumen del contenido incluido en la página 12
002986 1 10 11 6 2 2 12 7 3 9 13 8 4 14 5 9566CV 1 Grip 36 2 Wheel guard 3 Inner flange 82 4 Depressed center grinding wheel / Multi-disc 5 Lock nut 5/8-40 6 Rubber pad 125 7 Abrasive disc 8 Sanding lock nut 5/8-48 9 Wire wheel brush 10 Wire cup brush 11 Wheel guard (For cut-off wheel) 12 Inner flange 48 13 Cut-off wheel 14 Lock nut 5/8-48 - Lock nut wrench 28 12
Resumen del contenido incluido en la página 13
First-Class Postage Required Post Office will not deliver without proper postage. Makita U.S.A., Inc. 14930 Northam Street La Mirada, CA 90638-5753 Fold 13 Cut
Resumen del contenido incluido en la página 14
MAIL THIS PORTION Your answers to the following questions are appreciated. 1. This product was purchased from: 3. How did you learn about this product: Home Center Other ( ) Magazine Radio Hardware/Lumber Store From Dealer Exhibition Tool Distributor Newspaper From Friend Industrial Supply Store Display Previous Usage Construction Supply Catalog Other ( ) 2. Use of the product is intended for: 4. Most favored points are: Construction Trade Design Repair Se
Resumen del contenido incluido en la página 15
FACTORY SERVICE CENTERS 1-800-4-MAKITA RETAIN THIS PORTION FOR YOUR RECORDS ALABAMA COLORADO LOUSIANA NEW YORK PUERTO RICO 2365 Pelham Parkway 11839 E. 51st Ave. 5626 Jefferson Hwy. 4917 Genessee Street 200 Guayama St. Pelham, AL 35124 Denver, CO 80239-2709 Harahan, LA 70123 Cheektowaga, NY 14225 Hato Rey, PR 00917 (205) 620-1791 (303) 371-2850 (504) 733-4138 (716) 685-9503 (787) 250-8776 131-35 31st Ave. ARIZONA FLORIDA MARYLAND Flushing, NY 11354 TENNESSEE 3707 E. Broadway Rd., Ste. 6 620
Resumen del contenido incluido en la página 16
WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry products, and • arsenic and chromium from chemically-treated lumber. Your risk from these exposures varies, depending on how often you do this type of
