Resumen del contenido incluido en la página 1
Angle Drill
13 mm (1/2”)
MODEL DA4000LR
003009
DOUBLE
INSULATION
INSTR U CTION MANU AL
WARNING:
For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
www.makitatools.com
Resumen del contenido incluido en la página 2
SPECIFICATIONS Model DA4000LR Steel 13 mm (1/2”) Capacities Wood 38 mm (1-1/2”) High 0 - 900/min. No load speed (RPM) Low 0 - 400/min. Overall length 413 mm (16-1/4”) Net weight 3.7 kg (8.1 lbs) • Manufacturer reserves the right to change specifications without notice. Specifications may differ from country to country. GENERAL SAFETY RULES USA002-2 (For All Tools) WARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire
Resumen del contenido incluido en la página 3
change the plug in any way. Double insula- 13. Do not overreach. Keep proper footing and balance at all times. Proper footing and tion eliminates the need for the three wire balance enables better control of the tool in grounded power cord and grounded power unexpected situations. supply system. 14. Use safety equipment. Always wear eye 5. Avoid body contact with grounded sur- protection. Dust mask, non-skid safety faces such as pipes, radiators, ranges and shoes, hard hat, or hearing protectio
Resumen del contenido incluido en la página 4
model. Accessories that may be suitable for tenance performed by unqualified personnel one tool, may become hazardous when used could result in a risk of injury. on another tool. 24. When servicing a tool, use only identical replacement parts. Follow instructions in SERVICE the Maintenance section of this manual. 23. Tool service must be performed only by Use of unauthorized parts or failure to follow qualified repair personnel. Service or main- Maintenance instructions may create a risk of elec
Resumen del contenido incluido en la página 5
SPECIFIC SAFETY RULES USB001-2 DO NOT let comfort or familiarity with product (gained from repeated use) replace strict adherence to drill safety rules. If you use this tool unsafely or incorrectly, you can suffer serious personal injury. 1. Hold tool by insulated gripping surfaces 4. Keep hands away from rotating parts. when performing an operation where the 5. Do not leave the tool running. Operate the cutting tools may contact hidden wiring or tool only when hand-held. its own cord. Contact w
Resumen del contenido incluido en la página 6
SYMBOLS USD201-2 The followings show the symbols used for tool. V ....................... volts ....................no load speed n ˚ A ....................... amperes ....................Class II Construction Hz ..................... hertz .../min................revolutions or reciprocation per minute ................ alternating current 6
Resumen del contenido incluido en la página 7
FUNCTIONAL CAUTION: DESCRIPTION • Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. 003022 Switch action CAUTION: • Before plugging in the tool, always check to see that the 1 switch trigger actuates properly and returns to the “OFF” position when released. To start the tool, simply pull the switch trigger. Tool speed is increased by increasing pressure on the switch trigger. 1. Switch trigger Release the switch trigger to stop. 003029
Resumen del contenido incluido en la página 8
003044 Use of it with angle attachment Screw the side grip for the angle attachment on the angle housing. Then tighten the side grip by turning clockwise at the desired position. 003045 Use of it without angle attachment Screw the side grip on the tool barrel securely. The side grip can be installed on either side of the tool, whichever is con- venient. 003066 Installing or removing angle attachment The angle head has a spindle on each end. For higher speed operation, attach the drill chuck to t
Resumen del contenido incluido en la página 9
003068 Remove the chuck remaining bolt through the chuck opening by turning it counterclockwise with the hex wrench. CAUTION: 1 • The drill chuck and the bolt are assembled each other. Turn the bolt counterclockwise about 10 times so that they can be removed together. 1. Hex wrench 003069 Loosen the bolts of the joint by the hex wrench and remove the angle housing, the joint and the socket. 12 3 4 1. Angle housing 2. Joint 3. Socket 4. Bolt 003070 To install the socket and the joint, fit the soc
Resumen del contenido incluido en la página 10
003072 Slide the drill chuck to the spindle so that the two faces are 1 fitted perfectly. Holding the drill chuck with the chuck key, 2 tighten the bolt (for installing the drill chuck) clockwise with the hex wrench firmly. 3 4 1. Spindle 2. Two faces 3. Drill chuck 4. Chuck key 003073 The tool may be converted to a conventional straight drive drill by installing the drill chuck without the angle attachment. 1 2 1. Drill chuck 2. Spindle 003055 Installing or removing drill bit 1 To install the b
Resumen del contenido incluido en la página 11
Holding tool OPERATION When drilling a large hole with a hole saw, etc., the side grip (auxiliary handle) should be used as a brace to maintain safe control of the tool. Drilling operation Drilling in wood When drilling in wood, the best results are obtained with wood drills equipped with a guide screw. The guide screw makes drilling easier by pulling the bit into the workpiece. Drilling in metal To prevent the bit from slipping when starting a hole, make an indentation with a center-punch and h
Resumen del contenido incluido en la página 12
MAINTENANCE CAUTION: • Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. 001145 Replacing carbon brushes Remove and check the carbon brushes regularly. Replace when they wear down to the limit mark. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be replaced at the same time. Use only iden- tical carbon brushes. 1 1. Limit mark 003087 Use a screwdriver to remove the brush holder caps. Take
Resumen del contenido incluido en la página 13
First-Class Postage Required Post Office will not deliver without proper postage. Makita U.S.A., Inc. 14930 Northam Street La Mirada, CA 90638-5753 Fold 13 Cut
Resumen del contenido incluido en la página 14
MAIL THIS PORTION Your answers to the following questions are appreciated. 1. This product was purchased from: 3. How did you learn about this product: Home Center Other ( ) Magazine Radio Hardware/Lumber Store From Dealer Exhibition Tool Distributor Newspaper From Friend Industrial Supply Store Display Previous Usage Construction Supply Catalog Other ( ) 2. Use of the product is intended for: 4. Most favored points are: Construction Trade Design Repair Se
Resumen del contenido incluido en la página 15
FACTORY SERVICE CENTERS 1-800-4-MAKITA RETAIN THIS PORTION FOR YOUR RECORDS ARIZONA FLORIDA MISSOURI PENNSYLVANIA 3707 E. Broadway Rd., Ste. 6 750 East Sample Road 9876 Watson Road 1704 Babcock Blvd. Phoenix, AZ 85040 Pompano Beach, FL 33064 St. Louis, MO 63126-2221 Pittsburgh, PA 15209 (602) 437-2850 (954) 781-6333 (314) 909-9889 (412) 822-7370 CALIFORNIA GEORGIA NEBRASKA PUERTO RICO 41850 Christy St. 4680 River Green Parkway NW 4129 S. 84th St. 200 Guayama St. Fremont, CA 94538-5107 Duluth,
Resumen del contenido incluido en la página 16
WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry products, and • arsenic and chromium from chemically-treated lumber. Your risk from these exposures varies, depending on how often you do this type of
