Resumen del contenido incluido en la página 1
Driver Dr i I I
Cordless
MODEL 6012HD
MODEL 6012HDW
With Fast Charger and Carrylng Case
INSTRUCTION MANUAL
S PECl F I CAT1 0 N S
Model 6012HD
Steel Wood Wood screw Machine screw Nuts
6 5 mm 15 mm 5.1 mm x 55 mm 6 mm 261 mm 1.6 kg
1114"l 1518") 13/16" x 2-118") 1114")
I :Em) 1 400 ' lrloo 1 110-114") 1 13.5 lbsl
Battery Cartridge 9000
9 Model DC9700 Fast Charger
Voltage Input output Charging time
* Manufacturer reserves the right to change specifications without notice
* Note: Spe
Resumen del contenido incluido en la página 2
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFE- TY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PER- SONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2. CONSIDER WORK AREA ENVIRONMENT. Don't use power tools in damp or wet locations. Keep work area well lit. Don't expose power tools to rain. Don't use tool in presence
Resumen del contenido incluido en la página 3
13. DISCONNECT TOOLS. When not in use, before servicing, and when chang- ing accessories, such as blades, bits, cutters. 14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in. 16. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cords intended for
Resumen del contenido incluido en la página 4
1. SAVE THESE INSTRUCTIONS - This manual 2. 3. 4. 5. 6. 7. 8. Length of Cord (Feet) 25 50 100 150 AWG Size of Cord 18 18 18 16 9. Do not operate charger with damaged cord or plug - replace them imme- diately. 10. Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in any way; take it to a qualified serviceman. 11. Do not disassemble charger or battery cartridge; take it to a qualified serviceman when service or repair is required. Incorrect
Resumen del contenido incluido en la página 5
ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (5O0F1 or ABOVE 4OoC (104OF). 2. Do not attempt to use a step-up transformer, an engine generator or DC power receptacle. 3. Do not allow anything to cover or clog the charger vents. 4. Always cover the battery terminals with the battery cover when the battery cartridge is not used. 5. A battery short can cause a large current flow, overheating, possible burns and e
Resumen del contenido incluido en la página 6
Installing or removing battery cartridge 0Always switch off the tool before insertion or removal of the battery cartridge. 0 To remove the battery cartridge, pull out the set plate on the tool and grasp both Set plate I sides of the cartridge while withdrawing it from the barrel. 0 To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Snap the set plate back into place. Be sure to close the set plate fully be
Resumen del contenido incluido en la página 7
When you charge a new battery cartridge or a battery cartridge which has not been used for a long period, it may not accept a full charge. This is a normal condition and does not indicate a problem. You can recharge the battery cartridge fully after discharging it almost completely a couple of times. 0 If you wish to charge two battery cartridges, allow 15 minutes between chargings on the fast charger. Bit installation & removal CAUTION : Always set the Forward-Reverse switch lever to NE
Resumen del contenido incluido en la página 8
Drill *Punch a small hole in the metal to pre- vent the bit from skitterring when start- ing to drill a hole. 0 Use machine oil on the bit to facilitate drill ing. .Pressing down too hard on the tool will not speed up the drilling. In fact, this undue pressure will only serve to damage the tip of your drill bit, decrease your drilling per- formance and shorten the service of the tool. 0There is a tremendous force exerted on the tool/bit at the time of hole break through. Grip the drill
Resumen del contenido incluido en la página 9
Screw Item I Nominal diameter (mm) Match vour bit to vour screw. Bit No. I Wood screw I Machine screw I I 2.1 - 2.7 M2 - M2.6 Phillips bits Phillips bit No. 2-65 mm is standard 3.1 - 4.8 M3 - M5.5 equipped. Select your screws and nominal diameter with the chart on the right. No. 3 I 5.1 (13/64") I M6 (1/4") Slotted bits Unless you use a bit that fits properly the slot on the head of the screw, the slot will be damaged and the screw will not fasten. If the bit fails to match the slot
Resumen del contenido incluido en la página 10
Speed changeover .To change the speed, turn the speed change knob 180" while the drill is run- ning. Be sure that the speed change knob is turned to the correct speed setting before you begin operation. See arrow indication. Use the right speed for the job. Fastening torque adjustment Fastening torque Just turn the fastening torque adjust adjust knob knob on the tool in order to select any of 5 different fastening torques. Make sure that the arrow points to the right torque before
Resumen del contenido incluido en la página 11
*The hole on the heel of the tool is a con- to carry it by a cord, hook venient way or other means. I 11
Resumen del contenido incluido en la página 12
ACCESSORIES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this of injury to persons. The manual. The use of any other accessories or attachments might present a risk accessories or attachments should be used only in the proper and intended manner. 0 Fast charger 0 Charger 12V for car Model DC9700 Model DC9112 0 Makita Battery cartridge 9000 (9.6 V) 0 Chuck key S10 1 hour fast charge nickel cadmium battery Part No. 763419- 1 Par
Resumen del contenido incluido en la página 13
0 Tool carrying case 0 Tool holster Part No. 823085-7 (Steel case) has some bits storage space. Part No. 824145-8 (Plastic case) Use holster to carry drill only after removing bit. Also, keep the reversing switch lever in neutral position when carrying in the holster. Part No. 823033-36 Part No. 823033-3E (Genuine leather) 13
Resumen del contenido incluido en la página 14
Feb 19 86 EN CORDLESS DRIVER DRILL Model 6012HD Note: The switch and other part configurations may differ from country to country 14
Resumen del contenido incluido en la página 15
MODEL 6012HD Feb-19-86 EN ED DESCRIPTION DESCRIPTION MACHINE ______ 1 1 Pan Head Screw M5x18 25 4 Steel Ball 4 8 2 1 Drill Chuck S10 26 1 Clutch Cam 3 1 Spindle 27 1 Conical Compression Spring 16-21 4 I Pi" 3 28 I 08% 5 1 Ball Bearinq 6000LLB 29 1 Thrust Needle Gauge 1023 6 1 STOP Ring E 9 30 1 Flat Washer 8 Compresslo" Spr,ng 10 1 7 1 31 Slider 8 1 Thin Washer 10 32 1 P," 3 1 Spur Gear 78 1 9 33 Gear 12-28 10 1 Ring 16 34 1 Plane Bearing 4 11 1 Spur Gear 93 35 I Shifter 12 1 T
Resumen del contenido incluido en la página 16
The only way to dispose of a Makita battery is to recycle it. The law prohibits any other method of disposal. I Ni-Cd 1 To recycle the battery: 1. Remove the battery from the tool. 2. a). Take the battery to your nearest Makita Factory Service Center or b). Take the battery to your nearest Makita Authorized Service Center or Distributor that has been designated as a Makita battery recycling location. Call your nearest Makita Service Center or Distributor to determine the location that
