Resumen del contenido incluido en la página 1
WT-5600
Radio Controlled Projection Alarm
Instruction Manual
PROJECTION
Resumen del contenido incluido en la página 2
TABLE OF CONTENTS Topic Page Inventory of Contents 3 About WWVB 3 Quick Set-Up Guide 4 Detailed Set-Up Guide Battery Installation 5 Program Mode Programming Sequence 6 Function Buttons 6 Time Zone Setting 6-7 Time Setting 7 Date Setting 8 12/24-Hour Mode 8 DST (Daylight Saving Time) Setting 8 Features & Operations Features 8-9 Radio-Controlled Time 9 Projection 10 LCD light 10 Time Alarm 10-11 Changing Display Mode 12 Maintenance & Care 12 Troubleshooting 13 Specificatio
Resumen del contenido incluido en la página 3
INVENTORY OF CONTENTS 1) WT-5600 Alarm Clock 2) AC adapter/transformer 3) Instruction manual and warranty card. ADDITIONAL EQUIPMENT (not included) 1) Two fresh 1.5V AA batteries (optional for alarm clock) FEATURES OF PROJECTION ALARM 1. Radio-controlled time and date 2. Projection of time 3. LCD light 4. Three modes of date/second display 5. Alarm ABOUT WWVB (Radio Controlled Time) The NIST (National Institute of Standards and Technology—Time and Frequency Division) WWVB
Resumen del contenido incluido en la página 4
QUICK SET-UP GUIDE 1) Insert two AA batteries into the Projection alarm and/or plug into wall 2) Wait 10 minutes for WWVB reception. 3) If there is no WWVB reception, manually set the time and date (instructions in the Program Mode). 4) Program the settings. 5) Mount the WT-5600 in a suitable location, where WWVB signal can be received. 6) The projector will activate and remain on if the alarm clock is plugged in. If only batteries are used, the projector will only be activated when a
Resumen del contenido incluido en la página 5
DETAILED SET-UP GUIDE BATTERY INSTALLATION 1. Remove the battery cover. 2. Observe the correct polarity and install 2 AA batteries. 3. In addition or instead of inserting batteries, the AC adapter can be used. Simply plug the adapter into the receptacle on the bottom of AC adapter the alarm clock and then receptacle plug in adapter. 4. Replace the battery cover. 5. The projector will activate and remain on if the alarm clock is plugged in. If only batteries are used, the pro
Resumen del contenido incluido en la página 6
PROGRAM MODE To enter the Program Mode, hold down the “MODE+” button for 2 seconds, until the time zone (“-5” default) flashes in the lower right. The Program Mode Guide is laid out in a manner that allows you to program each function separately, or you can follow the instructions entirely to program the Projection Alarm. Complete programming is usually done for the initial set-up and will require you to skip step 1 of programming sections III through VIII. Press the “SNOOZE” button at
Resumen del contenido incluido en la página 7
-4h Atlantic Time -5h Eastern Time (default setting) -6h Central Time -7h Mountain Time -8h Pacific Time -9h Alaskan Time -10h Hawaiian Time -11h, -12h Next two time zones West of HAW 0h Greenwich Mean Time -1h, -2h, -3h Three time zones West of GMT 3. From –5h to –8h, a US map with the highlighted time zone will also be displayed to the right of the time display. 4. Press the “AL” button to move to the hour setting or press the “SNOOZE” button to confirm the
Resumen del contenido incluido en la página 8
E. DATE SETTING Note: When the WWVB signal is found, that date will over-ride the manually set date. 1. Hold down the “MODE/+” button for 2 seconds (the selected time zone will flash), press the “AL” button three times until the year flashes. 2. Press the “MODE/+” button to select the year. 3. Press the “AL” button to confirm the year and move to the month setting. 4. Press the “MODE/+” button to select the month. 5. Press the “AL” button to confirm the month and move to the day settin
Resumen del contenido incluido en la página 9
B. RADIO-CONTROLLED TIME AND DATE 1. The projection alarm will automatically search for the time signal upon initial set-up and every night. 2. When the signal is being received, there will be a “tower” icon flashing to the right of the time display. 3. When the time signal has been received successfully, the tower icon will remain steady until midnight. 4. The NIST (National Institute of Standards and Technology—Time and Frequency Division) WWVB radio station is located in Ft. Collins,
Resumen del contenido incluido en la página 10
C. PROJECTION OF TIME 1. When plugged into an AC outlet, the projection alarm can continuously project the time. 2. When operating on batteries alone, the Projection Alarm will only project when a button is pressed. 3. The projection will auto-focus for display from three to six feet away. A dark surrounding will be necessary to clearly see the projection. 4. The direction of the display can be rotated 360 ° in 90 ° increments by pressing the directional button. There is no display on
Resumen del contenido incluido en la página 11
2. ACTIVATING/DEACTIVATING THE ALARM a. After entering the alarm-setting mode, the alarm is activated. b. To toggle between activating Alarm is Active and deactivating the alarm, press the “AL” button briefly. “((( •)))” will be displayed to the left of the time display when the alarm is activated. c. When the snooze bar is pressed, the display will show the time the alarm is set to below the time display. 3. TURNING ALARM OFF (WHILE SOUNDING) Note: The alarm will sound for 23 se
Resumen del contenido incluido en la página 12
F. CHANGING DISPLAY MODE (DAY, SECONDS, AND ALARM TIME) There is three possible display modes to view the date, seconds and alarm time. To change the display (starting at the default of month - date): 1. Press the “MODE/+” button and the display will now show seconds. 2. Press the “MODE/+” button and the display will now show alarm time. 3. Press the “MODE/+” button and the display will now show month – date. MAINTENANCE & CARE B. Extreme temperatures, vibrations and shock shou
Resumen del contenido incluido en la página 13
TROUBLESHOOTING Problem: The Projection is faint Solution: 1) Change intensity setting 2) Use AC adapter 3) Darken surroundings 4) Use fresh batteries (if AC is not used) Problem: The LCD is faint. Solution: 1) Replace the batteries. Problem: No reception of WWVB signal. Solution: 1) It may help reception to face the front of the Projection alarm in the general direction of Ft. Collins, Colorado. 2) Wait overnight for signal. 3) Be sure the Projection alarm is at least 6 feet from an
Resumen del contenido incluido en la página 14
WARRANTY INFORMATION La Crosse Technology, Ltd provides a 1-year limited warranty on this product against manufacturing defects in materials and workmanship. This limited warranty begins on the original date of purchase, is valid only on products purchased and used in North America and only to the original purchaser of this product. To receive warranty service, the purchaser must contact La Crosse Technology, Ltd for problem determination and service procedures. Warranty service can on
Resumen del contenido incluido en la página 15
For warranty work, technical support, or information contact: La Crosse Technology 2809 Losey Blvd. S. La Crosse, WI 54601 Phone: 608.782.1610 Fax: 608.796.1020 e-mail: support@lacrossetechnology.com (warranty work) sales@lacrossetechnology.com (information on other products) web: www.lacrossetechnology.com FCC ID: OMO-01RX (receiver) THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: 1. THIS DEVICE MAY NO