Resumen del contenido incluido en la página 1
IM548
October, 2004
K206 Flux-Cored Fume Gun
Safety Depends on You
Lincoln arc welding and cutting
equipment is designed and built
with safety in mind. However, your
overall safety can be increased by
proper installation ... and thought-
ful operation on your part. DO
NOT INSTALL, OPERATE OR
REPAIR THIS EQUIPMENT
WITHOUT READING THIS
MANUAL AND THE SAFETY
PRECAUTIONS CONTAINED
THROUGHOUT. And, most
importantly, think before you act
and be careful.
OPERATOR’S MANUAL
Copyright © 2004 Lincoln Glob
Resumen del contenido incluido en la página 2
i i SAFETY WARNING CALIFORNIA PROPOSITION 65 WARNINGS Diesel engine exhaust and some of its constituents The engine exhaust from this product contains are known to the State of California to cause can- chemicals known to the State of California to cause cer, birth defects, and other reproductive harm. cancer, birth defects, or other reproductive harm. The Above For Diesel Engines The Above For Gasoline Engines ARC WELDING CAN BE HAZARDOUS. PROTECT YOURSELF AND OTHERS FROM POSSIBLE SERIOUS INJURY
Resumen del contenido incluido en la página 3
ii ii SAFETY ELECTRIC SHOCK can ARC RAYS can burn. 4.a. Use a shield with the proper filter and cover kill. plates to protect your eyes from sparks and 3.a. The electrode and work (or ground) circuits the rays of the arc when welding or observing are electrically “hot” when the welder is on. open arc welding. Headshield and filter lens Do not touch these “hot” parts with your bare should conform to ANSI Z87. I standards. skin or wet clothing. Wear dry, hole-free gloves to insulate hands. 4.b. Us
Resumen del contenido incluido en la página 4
iii iii SAFETY WELDING SPARKS can CYLINDER may explode cause fire or explosion. if damaged. 6.a. Remove fire hazards from the welding area. 7.a.Use only compressed gas cylinders If this is not possible, cover them to prevent containing the correct shielding gas for the the welding sparks from starting a fire. process used and properly operating Remember that welding sparks and hot regulators designed for the gas and materials from welding can easily go through small cracks pressure used. All hos
Resumen del contenido incluido en la página 5
iv iv SAFETY 5. Toujours porter des lunettes de sécurité dans la zone de PRÉCAUTIONS DE SÛRETÉ soudage. Utiliser des lunettes avec écrans lateraux dans les zones où l’on pique le laitier. Pour votre propre protection lire et observer toutes les instruc- tions et les précautions de sûreté specifiques qui parraissent 6. Eloigner les matériaux inflammables ou les recouvrir afin de dans ce manuel aussi bien que les précautions de sûreté prévenir tout risque d’incendie dû aux étincelles. générales su
Resumen del contenido incluido en la página 6
v v for selecting a QUALITY product by Lincoln Electric. We want you to take pride in operating this Lincoln Electric Company product Thank You ��� as much pride as we have in bringing this product to you! Please Examine Carton and Equipment For Damage Immediately When this equipment is shipped, title passes to the purchaser upon receipt by the carrier. Consequently, Claims for material damaged in shipment must be made by the purchaser against the transportation company at the time the shipment
Resumen del contenido incluido en la página 7
1 1 1 DESCRIPTION The Flux-Cored Fume Gun can also be used at 400 amperes, 30% duty cycle. 2 The K206 is a Flux-Cored Fume Gun rated 350 Low cost tip available as parts order. Wear life may be 1/3 to 1/5 that of standard that of standard contact tip. Main application will be where cus- 1 amperes 60% duty cycle . It was developed to remove tomer has high replacement due to arcing tip to work. Tip can be identified smoke emitted at the arc when welding with by a vee groove on O.D. Innershield e
Resumen del contenido incluido en la página 8
2 2 Cored Fume Gun gun and still maintain good smoke Welding conditions will affect the air flow required for pickup. adequate smoke removal. 65 ft.(20m) when one gun is used on K184 vacuum unit 1. At the same welding currents, NS-3M electrodes 35 ft.(11m) when one gun is used on K179 vacuum unit require less air flow than NR-311 electrodes. Extension guides (which include the spatter shield) 2. Horizontal and position fillet welds require less air and nozzle contact tips wear or deteriorate w
Resumen del contenido incluido en la página 9
NOTES K206 FLUX CORED FUME GUN
Resumen del contenido incluido en la página 10
● Do not touch electrically live parts or ● Keep flammable materials away. ● Wear eye, ear and body protection. electrode with skin or wet clothing. WARNING ● Insulate yourself from work and ground. Spanish ● No toque las partes o los electrodos ● Mantenga el material combustible ● Protéjase los ojos, los oídos y el bajo carga con la piel o ropa moja- fuera del área de trabajo. cuerpo. AVISO DE da. ● Aislese del trabajo y de la tierra. PRECAUCION French ● Ne laissez ni la peau ni des vête- ● Gar
Resumen del contenido incluido en la página 11
● Keep your head out of fumes. ● Turn power off before servicing. ● Do not operate with panel open or ● Use ventilation or exhaust to guards off. WARNING remove fumes from breathing zone. Spanish ● Los humos fuera de la zona de res- ● Desconectar el cable de ali- ● No operar con panel abierto o piración. mentación de poder de la máquina guardas quitadas. AVISO DE ● Mantenga la cabeza fuera de los antes de iniciar cualquier servicio. humos. Utilice ventilación o PRECAUCION aspiración para gases.
Resumen del contenido incluido en la página 12
� World's Leader in Welding and Cutting Products � � Sales and Service through Subsidiaries and Distributors Worldwide � Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB SITE: www.lincolnelectric.com
