Manual de instrucciones de Life Fitness 90X

Resumen del contenido incluido en la página 1

93Xi, 90X Total Body Trainers
Assembly Instructions

Resumen del contenido incluido en la página 2

Congratulations... and welcome to the world of The following Parts List and the step-by-step assembly procedures have been assembled to make the set-up of the Total Body Trainer as quick and easy as possible. Please take special note of the following important points prior to choosing a location and beginning assembly of the Total Body Trainer.

Resumen del contenido incluido en la página 3

IMPORTANT SAFETY INSTRUCTIONS! DO NOT LOCATE THE CROSS-TRAINER OUTDOORS, NEAR SWIMMING POOLS, OR IN AREAS OF HIGH HUMIDITY. DO NOT OPERATE YOUR CROSS-TRAINER IF IT HAS BEEN DROPPED, DAMAGED, OR EVEN PARTIALLY IMMERSED IN WATER. IF THIS OCCURS, CONTACT LIFE FITNESS CUSTOMER SUPPORT SERVICES AT THE NUMBER IN THE OPERATION MANUAL. DO NOT LOCATE THE CROSS-TRAINER ANY CLOSER THAN 30 INCHES (76 CM ) TO A TELEVISION SET. DO NOT LOCATE ADDITIONAL CROSS-TRAINERS ANY CLOSER THAN 42 INCHES (

Resumen del contenido incluido en la página 4

TOOLS REQUIRED FOR ASSEMBLY... Magnetic #2 Bit Phillips Screwdriver, T-45 Hex Key Wrench, 16mm Open End Wrench PARTS DESCRIPTION 1 Torx Socket Head Screw Qty: 12 2 Phillips Pan Head Screw Qty: 14 M8 – 1.25 x 19 M4 – 0.70 x 19 0017-00101-1791 0017-00101-1796 3 Phillips Pan Head Screw Qty: 2 4 Console Assembly Qty: 1 M4.2 – 0.70 x 10 0017-00101-1846 5 Front Rocker Cover Qty: 2 6 Left Back Rocker Cover Qty: 1 OK62-01009-0000 OK62-01011-0000 7 Console Support Assembly Qty: 1 8 Cons

Resumen del contenido incluido en la página 5

IMPORTANT! DO NOT DISCARD THE SHIP KIT LOCATED ON TOP OF THE PEDAL LEVERS. ALL NECESSARY COMPONENTS NEEDED TO COMPLETE THE INSTALLATION ARE LOCATED IN THE SHIP KIT. IMPORTANT! NE JETEZ PAS LE KIT PLACÉ SUR LE DESSUS DES LEVIERS DE PÉDALE. IL CONTIENT TOUS LES ÉLÉMENTS NÉCESSAIRES POUR L'INSTALLATION. 1. Locate the LEFT HANDLEBAR (11). Position the HANDLEBAR near the top of the LEFT PIVOT ARM (A). Align the mounting holes of the LEFT HANDLEBAR with the mounting holes 11 at the top of

Resumen del contenido incluido en la página 6

8. Locate the DISPLAY CONSOLE (4). Position the CONSOLE near the top of the CONSOLE BRACKET. Attach all CONNECTORS (F & G) leading from P Q the CONSOLE BRACKET to their corresponding CONNECTORS in the back of the DISPLAY CONSOLE. Feed any excess WIRE HARNESS into F G the CONSOLE BRACKET and place the DISPLAY CONSOLE onto the 2 7 CONSOLE BRACKET aligning the mounting holes. Secure the DISPLAY 21 4 CONSOLE using four SCREWS (2). Tighten the SCREWS securely. Do not over-tighten the SCREWS.

Resumen del contenido incluido en la página 7

Resumen del contenido incluido en la página 8

PRE-OPERATION CHECKLIST Ensure that all fasteners are tight. Make sure the CROSS-TRAINER is properly leveled and stable. (Refer to the Operation Manual) Ensure that the Leveler Jam Nuts are tight. (Refer to the Operation Manual) Read the entire Operation manual before using the Cross-Trainer. LISTE DES VÉRIFICATIONS À EFFECTUER AVANT LA MISE EN MARCHE Vérifiez si tous les dispositifs de fixation sont serrés Vérifiez si l'APPAREIL D'EXERCICE POLYVALENT est de niveau et stable.