Resumen del contenido incluido en la página 1
OUTDOOR BUILT-IN DUAL SIDE BURNERS
Installation Instructions and Use & Care Guide
For questions about features, operation/performance, parts, accessories or service, call: 1-800-422-1230
or visit our website at www.kitchenaid.com
In Canada, call for assistance, installation and service, call: 1-800-807-6777
or visit our website at www.KitchenAid.ca
DEUX BRÛLEURS LATÉRAUX ENCASTRÉS
POUR USAGE EXTÉRIEUR
Instructions d’installation et Guide d’utilisation et d’entretien
Au Canada, pour assistance,
Resumen del contenido incluido en la página 2
OUTDOOR BUILT-IN SIDE BURNER SAFETY Your safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.” These words mean: You can be killed or seriously injured if you
Resumen del contenido incluido en la página 3
IMPORTANT: This side burner is manufactured for outdoor use only. For side burners that are to be used at elevations above 2000 ft (609.6 m) orifice conversion is required. See “Gas Supply Requirements” section. It is the responsibility of the installer to comply with the minimum installation clearances specified on the model/serial rating plate. The model/serial rating plate can be found on the right-hand side panel. Copies of the standards listed may be obtained from: National Fire Protecti
Resumen del contenido incluido en la página 4
TABLE OF CONTENTS TABLE DES MATIÈRES OUTDOOR BUILT-IN SIDE BURNER SAFETY ............................2 SÉCURITÉ DU BRÛLEUR LATÉRAL ENCASTRÉ D'EXTÉRIEUR..........................................................25 INSTALLATION REQUIREMENTS ................................................5 EXIGENCES D'INSTALLATION...................................................27 Tools and Parts ............................................................................5 Outillage et pièces.....................
Resumen del contenido incluido en la página 5
INSTALLATION REQUIREMENTS Tools and Parts Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here. 20 lb LP Gas Models Natural Gas Models Tools Needed Tools Needed ■ Tape measure ■ Wrench or pliers ■ Tape measure ■ Wrench or pliers ■ Small, flat-blade screwdriver ■ Pipe wrench ■ Small, flat-blade screwdriver ■ Pipe wrench ■ Flat-blade screwdriver ■ Scissors or cutting pliers ■ Flat-blade screwdriver ■ Scissors or cut
Resumen del contenido incluido en la página 6
Style 2 - Side by Side Built-In Dual Side Burners Location Requirements Select a location that provides minimum exposure to wind and traffic paths. The location should be away from strong draft A areas. Do not obstruct flow of combustion and ventilation air. Clearance to combustible construction for built-in outdoor side burners: B B ■ A minimum of 24" (58 cm) must be maintained between the sides and back and any combustible construction. ■ A zero clearance may be maintained below the cooki
Resumen del contenido incluido en la página 7
The dimension chart and illustration below include cutout dimensions and minimum spacing requirements for all built-in outdoor products. The illustration is for reference. The design of your cabinet layout can be personalized, but the dimensions for the cutouts and minimum spacing must be followed. C C E D A E H D K L K J K G K K F B M Minimum Spacing Requirement Between Cutouts - Dimension K Between 2 or more sets of Access Doors adjacent to each other: K = 14" (35.6 cm) when 2 adjacent doors
Resumen del contenido incluido en la página 8
Cutout Dimensions - Built-in Grill Grill Size Dimension C Dimension D Dimension E 27" (68.6 cm) 29⁵⁄₈" (75.2 cm) 10¾" (27.3 cm) 22⁷⁄₈" (58.1 cm) 36" (91.4 cm) 38⁵⁄₈" (98.1 cm) 10¾" (27.3 cm) 22⁷⁄₈" (58.1 cm) 48" (121.9 cm) 50⁵⁄₈" (128.6 cm) 10¾" (27.3 cm) 22⁷⁄₈" (58.1 cm) Cutout Dimensions - Built-in Grill with Insulated Jacket Grill Size Dimension C Dimension D Dimension E 27" (68.6 cm) 33" (83.8 cm) 11¾" (29.8 cm) 24" (61.0 cm) 36" (91.4 cm) 42" (106.7 cm) 11¾" (29.8 cm) 24" (61.0 cm) 48" (121
Resumen del contenido incluido en la página 9
Cutout Dimensions - Built-in Warming Drawer Warming Drawer Size Dimension J 24" (61.0 cm) 22½" (57.2 cm) Cutout Dimensions - Built-in Utility Drawer and Built-in Trash Drawer Dimension M Dimension L* 12¼" (31.1 cm) 1½" (3.8 cm) *Dimension L is the minimum mounting surface area around the opening for mounting the optional door or drawers. Built-in Outdoor Grill Enclosure Ventilation for LP Gas: An enclosure for an LP gas fuel tank is to be ventilated by openings at both the top and lower levels
Resumen del contenido incluido en la página 10
Gas Conversion: Recommended Ground Method No attempt shall be made to convert the side burner from the gas specified on the model/serial rating plate for use with a different The outdoor side burner, when installed, must be electrically gas type without consulting the serving gas supplier. The conversion kits supplied with the side burner must be used. See grounded in accordance with local codes or, in the absence of local codes, with the National Electrical Code ANSI/NFPA 70, or “Gas Conve
Resumen del contenido incluido en la página 11
The 20 lb LP gas fuel tank must be mounted and secured. The gas supply line shall be equipped with an approved shutoff valve. This valve should be located in the same area as the side Door Style Tank Tray burner and should be in a location that allows ease of opening 1. Open cabinet doors. and closing. Do not block access to the shutoff valve. The valve 2. Pull out the tank tray. is for turning on or shutting off gas to the side burner. B A C Tank tray A. Gas supply line B. Shutoff valve “op
Resumen del contenido incluido en la página 12
Gas Connection Requirements For Models Equipped for Natural Gas Natural Gas LP Gas Conversion Using a Local LP Gas Supply Built-in side burner models are equipped for use with Natural Conversion must be made by a qualified person. A qualified gas. They are design-certified by CSA International for LP Natural gas technician shall provide the LP gas supply to the (propane or butane) gases with appropriate conversion. selected side burner location in accordance with the National Fuel Gas Code AN
Resumen del contenido incluido en la página 13
INSTALLATION INSTRUCTIONS 3. Remove the top nuts (4) from the tank tray assembly and lift the tank tray off of the mounting brackets. Built-in Outdoor Side Burner Installation A WARNING B Excessive Weight Hazard C D Use two or more people to move and install side E burner. Failure to do so can result in back or other injury. ■ Unpack side burner. Remove all packaging materials and A. Top nut remove side burner from carton. B. Tank tray C. Bottom nut ■ Place side burner into outdoor enclosure
Resumen del contenido incluido en la página 14
7. The tank tray for the 20 lb LP gas fuel tank must be adjusted To Install the 20 lb LP Gas Fuel Tank: so that the bottom of the tank tray is ¹⁄₈" (0.32 cm) above the 1. Open cabinet doors. cabinet door opening and is level. The top nut on each of the 2. Pull out the tank tray. mounting brackets is to be loose. Turn the bottom nuts counterclockwise to raise the tank tray and turn the bottom nuts clockwise to lower the tank tray. When the tank tray is level and slides in and out without to
Resumen del contenido incluido en la página 15
2. Open the manual shutoff valve in the gas supply line. The Gas Connection to Natural Gas or Local LP Gas valve is open when the handle is parallel to the gas pipe. WARNING A B A. Closed valve B. Open valve Explosion Hazard 3. Test all connections by brushing on an approved noncorrosive leak-detection solution. Bubbles will show a Use a new CSA International approved “outdoor” leak. Correct any leak found. gas supply line. Securely tighten all gas connections. Plug in Side Burner If connec
Resumen del contenido incluido en la página 16
4. Gently slide the side burner completely into the outdoor enclosure. Assemble Cooking Area 1. Lift off cover and grate and set aside. WARNING A B Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death, A. Cover fire, or electrical shock. B. Grate 2. Remove packing from around burners. 5. Plug 3-prong power cord plug into a grounded 3-prong GFI outl
Resumen del contenido incluido en la página 17
GAS CONVERSIONS For Models Equipped for Use with a 20 lb LP gas Tank NOTE: Models that are equipped for Natural gas require Gas Conversion Kit Part Number W10118099 for conversion to LP gas. Use the conversion instructions included in the kit. See “Assistance or Service” section for information on ordering. Tools and Parts for Gas Conversion Conversion to a Local LP Gas Supply Gather the required tools and parts before starting installation. Installation of the regulator Read and follow the in
Resumen del contenido incluido en la página 18
9. Use pipe wrench to install the convertible regulator. Brass cap will be facing up when tight. Conversion from LP Gas to Natural Gas A B Installation of the regulator 1. Turn off the main gas supply valve. 2. Unplug side burner or disconnect power. 3. Disconnect 20 lb LP gas fuel tank (if present). 4. Turn off all burner control valves. A. Brass connector 5. Remove rear cover and 2 screws. B. Convertible regulator 10. To set the appliance regulator for LP gas, use adjustable wrench to remove
Resumen del contenido incluido en la página 19
9. Use pipe wrench to install the convertible regulator. Brass 4. Use 10 mm socket and wrench or 10 mm nut driver to install cap will be facing up when tight. the new 2.1 mm orifices supplied with this kit. NOTE: The number 2.1 is stamped on the orifice for A B identification. 5. Repeat the procedure for the other burner. 6. Replace the burner top and caps. Align the notches in the bottom of the burner top with the tabs on the burner base and twist until the burner top is seated on the burne
Resumen del contenido incluido en la página 20
Low Flame Adjustment If flame goes out on the “LO” setting, the low flame setting must 6. Adjust flame to minimum stable flame. be adjusted. A 1. Turn off the valve and wait until burners are cool. 2. Light side burner using information in the “Outdoor Side Burner Use” section. 3. Turn burner to its lowest setting and remove knob. 4. Hold valve stem with pliers and insert a small flat-blade screwdriver into the shaft. B C 5. Watch the flame and slowly turn the screwdriver A. Valve stem counte
