Resumen del contenido incluido en la página 1
NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
Hardware Pack
Assembly Instruction
EVERLAST
Parts List
SMITH BENCH
Warranty
EVE-890
Ordering Parts
Model
EVE-890
Retain This
Manual for
Reference
08-16-05
OWNER'S
MANUAL
Made under license from trademark owner Everlast Worldwide
Inc., New York.
IMPEX INC.
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899
Resumen del contenido incluido en la página 2
TABLE OF CONTENTS BEFORE YOU BEGIN...................................................................................... 1 IMPORTANT SAFETY NOTICE....................................................................... 2 HARDWARE PACK…….......…....................................................................... 4 ASSEMBLY INSTRUCTIONS........................................................................... 5 EXPLODED DIAGRAM.......................................................
Resumen del contenido incluido en la página 3
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person
Resumen del contenido incluido en la página 4
WARNING LABEL REPLACEMENT The warning label shown here has been placed on the Cross Brace. If the label is missing or illegible, please call customer service at 1-800-888-8899 for replacement. Apply the label in the location shown. 3
Resumen del contenido incluido en la página 5
HARDWARE PACK 4
Resumen del contenido incluido en la página 6
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended two or more people assembling this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Note: Do not tighten the nuts and bolts until instructed to do so. B.) Plug four 2” Stabilizer End Caps (#24) onto the end of the two Stabilizers (#1). C.) Connect the two Stabilizers (#1) by a Cross Brace (#4) in the mid-span. Align the holes and
Resumen del contenido incluido en la página 7
STEP 2 (See Diagram 2) A.) Slide both a Rubber Bumper (#26) and Safety Stop (#6) onto a Guide Rod (#5). B.) Slide a Sliding Bar Catch (#8) onto the Guide Rod. C.) Insert the bottom of the Guide Rod into the ring cap on the left Stabilizer. Insert the top of Guide Rod into the ring cap on top of the left Upright Beam. Use the two M8 x ½” Allen Screws (#16) on the caps to secure the Guide Rod. D.) Attach a Safety Hook (#7) to the bracket on the Safety Stop. Secure it with one M10 x 1 5/8
Resumen del contenido incluido en la página 8
STEP 3 (See Diagram 3) A.) NOTE: Help of another person is strongly recommended for this step. Place the Lifting Sleeve (#10) in between the two Sliding Bar Catches (#8). Align the holes and insert the Weight Bar (#9) into the Bar Catch from one end and through the Lifting Sleeve to the other Bar Catch on the opposite end. Center the Weight Bar and secure it to each Bar Catch with one M10 x 5/8” Allen Bolt (#15). B.) Turn the hook on the Lifting Sleeve into the selected holes on the
Resumen del contenido incluido en la página 9
STEP 4 (See Diagram 4) A.) Plug four Stabilizer End Caps (#24) onto each end of the Front and Rear Stabilizers (#35 & #36). B.) Attach the Main Seat Support (#30) to the Rear & Front Stabilizers (#35 & #36). Secure each end with one 4 ¾” x 2” Bracket (#12), two M10 x 2 ¾” Carriage Bolts (#18), two Ø ¾” Washers (#14), and two M10 Aircraft Nuts (#17). DIAGRAM 4 8
Resumen del contenido incluido en la página 10
STEP 5 (See Diagram 5) A.) Attach the side-holes on the Backrest Supports (#33) to the long pivot on the Main Seat Support (#30). Insert one M10 x 7 ¼” Allen Bolt (#47) through the holes and secure it with two Ø ¾” Washers (#14), and one M10 Aircraft Nut (#17). B.) Place the Backrest Incline Support (#34) in between the two Backrest Supports (#33). Align the holes and secure it with one M10 x 7 ¼” Allen Bolt (#47), two Ø ¾” Washers (#14), and one M10 Aircraft Nut (#17). Do not tighten
Resumen del contenido incluido en la página 11
STEP 6 (See Diagram 6) A.) Place the Backrest Board (#32) onto the Backrest Supports. Secure it with four M6 x 2 1/8” Hex Bolts (#50) and ؽ” Washers (#49). B.) Place the Seat (#34) onto the Seat Incline Support. Secure it with four M6 x 5/8” Hex Bolts (#53) and Ø ½” Washers (#49). Insert a L-shaped Pin (#41) to lock the Seat in desired Incline position. C.) Insert three Foam Tubes (#37) halfway through the holes on the Leg Developer and the Main Seat Support. Push six Foam Rolls (#
Resumen del contenido incluido en la página 12
11
Resumen del contenido incluido en la página 13
PARTS LIST KEY NO. DESCRIPTION Q’ty 1 Stabilizer 2 2 Rear Support 2 3 Upright Beam 2 4 Cross Brace 2 5 Guide Rod 2 6 Safety Stop 2 7 Safety Hook 2 8 Sliding Bar Catch 2 9 Weight Bar 1 10 Lifting Sleeve 1 11 Weight Storage Post 2 12 4 ¾” x 2” Bracket 6 13 6 ¼” x 2” Bracket 2 14 ∅ ¾” Washer 36 15 M10 x 5/8” Allen Bolt 2 16 M8 x ½” Allen Screw 7 17 M10 Aircraft Nut 28 18 M10 x 2 ¾” Carriage Bolt 20 19 M10 x 2 ½” Allen Bolt 2 20 M10 x 1 5/8” Allen Bolt 2 21
Resumen del contenido incluido en la página 14
IMPEX INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX Cust
