Manual de instrucciones de Harbor Freight Tools CENTRALPNEUMATIC 97526

Resumen del contenido incluido en la página 1

AIR PIN NAILER
23-GAUGE
Model 97526
ASSEMBLY AND OPERATING INSTRUCTIONS
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
© ®
Copyright 2007 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools. Diagrams within this manual may n

Resumen del contenido incluido en la página 2

oxygen, carbon dioxide, combustible SPECIFICATIONS gases, or any other bottled gas as a power source for this tool. Fastener Type/Gauge Headless Pins, 23 Gauge Magazine Capacity 100 Pins 2. Keep your work area clean and Operating Pressure 60-100 PSI; 120 PSI Max. well lit. Cluttered benches and dark areas invite accidents. Air Consumption 5.5 CFM @ 90 PSI Air Inlet 1/4” - 18 NPT 3. Use protection: Always wear ANSI- Pin Length Settings 1/2”, 5/8”, 3/4”, 7/8”, 1’” approved safety eye goggles

Resumen del contenido incluido en la página 3

8. Avoid accidental starting. Carrying and safer at the rate for which it is power tools with your finger on the designed. Do not force the tool and Trigger (27) invites accidents. do not use the tool for a purpose for which it is not intended. 9. Be sure all tools and/or attachments used with this Air 17. Do not use the Air Nailer if the Nailer are secure before plugging Trigger (27) does not turn it on in or turning on the air supply. or off. Any tool that cannot be controlled with t

Resumen del contenido incluido en la página 4

6. Never leave this Air Nailer SERVICE unattended when it is plugged into 1. Tool service must be performed an air supply. Turn off the tool, and only by qualified repair personnel. unplug it from an air supply before Service or maintenance performed by leaving. unqualified personnel could result in 7. WARNING: This product contains a risk of injury. or, when used, produces a 2. When servicing, use only identical chemical known to the State of replacement parts. Follow Californ

Resumen del contenido incluido en la página 5

If you are not using an automatic UNPACKING AND SET UP oiler system, before operation add a When unpacking, check to make sure few drops of Pneumatic Tool Oil (not that the item is intact and undamaged. If included) to the airline connection. any parts are missing or broken, please Add a few drops after each hour of call Harbor Freight Tools at the number continual use. shown on the cover of this manual as soon Set the air pressure range on the as possible. regulator so that it is betwe

Resumen del contenido incluido en la página 6

9. In case of a fastener jam, take your OPERATION INSTRUCTIONS finger off the Trigger (27). Rotate the 1. Before use, add a few drops of Trigger Lock/Safety (60) clockwise pneumatic tool oil (not included) into or counter-clockwise. For instance, the Inlet. a “6 o-clock” position will lock the Trigger (27) and the tool will not fire. 2. Attach the Air Coupler (61) to Air However, “3 o-clock” and “9 o-clock” Inlet using pipe thread seal tape (not positions unlock the Trigger (27), in

Resumen del contenido incluido en la página 7

INSPECTION, MAINTENANCE, AND CLEANING 1. WARNING! Make sure air compressor is unplugged and that the Nailer is disconnected from its Air Supply before performing any inspection, maintenance, or cleaning procedures. 2. BEFORE EACH USE, inspect the general condition of this tool. Check for loose screws, misalignment or binding of moving parts, cracked or broken parts, damaged air hoses, and any other condition that may affect its safe operation. If abnormal noise or vibration occurs, have

Resumen del contenido incluido en la página 8

PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLAC

Resumen del contenido incluido en la página 9

Air Coupler (61) not shown. ASSEMBLY DIAGRAM SKU 97526 For technical questions, please call 1-800-444-3353. Page 9

Resumen del contenido incluido en la página 10

90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, norm