Manual de instrucciones de Grizzly G4003G

Manual de instrucciones del aparato Grizzly G4003G

Aparato: Grizzly G4003G
Categoría: Torno
Fabricante: Grizzly
Tamaño: 16.47 MB
Fecha de añadido: 4/14/2014
Número de páginas: 72
Imprimir el manual

Descargar

¿Cómo se utiliza?

Nuestro propósito es proporcionarte el acceso más rápido posible a los contenidos incluidos en los manuales de instrucciones del aparato Grizzly G4003G. Utilizando la vista previa online, puedes ver rápidamente el índice de contenidos y pasar a la página donde encontrarás la solución a tu problema con Grizzly G4003G.

Para tu comodidad

Si ver los manuales de instrucción de Grizzly G4003G directamente en esta página no es cómodo para ti, puedes utilizar dos soluciones posibles:

  • Vista en pantalla completa – Para ver cómodamente los manuales de instrucciones (sin descargarlos en tu ordenador) puedes utilizar el modo de vista en pantalla completa. Para activar la vista del manual Grizzly G4003G en pantalla completa, utiliza el botón Pantalla completa
  • Descargar al ordenador – también puedes descargar el manual de instrucciones de Grizzly G4003G a tu ordenador y guardarlo en tu colección. Sin embargo, si no quieres ocupar espacio en tu dispositivo, siempre podrás descargarlo de ManualsBase.
Grizzly G4003G Manual de instrucciones - Online PDF
Advertisement
« Page 1 of 72 »
Advertisement
Versión impresa

Muchas personas prefieren no leer el documento en la pantalla, sino en versión impresa. La opción de impresión también está prevista y puedes utilizarla haciendo clic en el enlace más arriba - Imprimir el manual. No tienes que imprimir el manual completo de Grizzly G4003G, solo las páginas que elijas. Ahorra papel.

Resúmenes

A continuación encontrarás resúmenes de los contenidos incluidos en las páginas posteriores del manual de instrucciones para Grizzly G4003G. Puedes utilizarlos si quieres ver rápidamente el contenido que se encuentra en la siguientes páginas del manual.

Resúmenes de contenidos
Resumen del contenido incluido en la página 1

MODEL G4003G
GUNSMITH'S LATHE
OWNER'S MANUAL
COPYRIGHT © MAY, 2007 BY GRIZZLY INDUSTRIAL, INC., REVISED OCTOBER, 2007 (TR)
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#CRTRTS9327 PRINTED IN CHINA

Resumen del contenido incluido en la página 2

����������������������������������������������������������������������� �������������������������������������������������������������� ���������������������������������������������������������������������� �������������������������������������������������������������������� ������������������������ ������������������������������������������������������������������ �������������������������������������������������������������������� ���������������������������������������������������������������

Resumen del contenido incluido en la página 3

Table of Contents INTRODUCTION ............................................... 2 SECTION 5: ACCESSORIES ......................... 31 Foreword ........................................................ 2 SECTION 6: MAINTENANCE ......................... 33 Contact Info ................................................... 2 Basic Maintenance ...................................... 33 Machine Data Sheet ...................................... 3 Lubrication ................................................

Resumen del contenido incluido en la página 4

INTRODUCTION Foreword Contact Info We are proud to offer the Model G4003G If you have any comments regarding this manual, Gunsmith's Lathe. This machine is part of a grow- please write to us at the address below: ing Grizzly family of fine metalworking machinery. When used according to the guidelines set forth in Grizzly Industrial, Inc. C this manual, you can expect years of trouble-free, /O Technical Documentation Manager enjoyable operation and proof of Grizzly’s com- P.O. Box 2069 mitment

Resumen del contenido incluido en la página 5

Machine Data Sheet MACHINE DATA SHEET Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901 MODEL G4003G GUNSMITH'S BENCH TOP LATHE WITH MODEL G4003G STAND GUNSMITH'S BENCH TOP LATHE WITH STAND Product Dimensions: Weight............................................................................................................................................................ 1213 lbs. Length/Width/Height.........................................................

Resumen del contenido incluido en la página 6

Headstock Info Spindle Bore...........................................................................................................................................1-5/8 in. Spindle Size........................................................................................................................................... 3-1/4 in. Spindle Taper.............................................................................................................................................MT#5 No

Resumen del contenido incluido en la página 7

Identification N I H J O K L M G P R F S T Q E U D C V B W X A Y Z AA FF CC EE BB DD Figure 1. Model G4003G identification. A. Quick Change Gearbox Levers Q. Compound Rest Handwheel B. Feed Rod Lever R. Tailstock Spindle and Center C. Emergency Stop/RESET Button S. Tailstock Spindle Lock Lever D. POWER START Button T. Tailstock Spindle Handwheel E. Inching/Jog Button U. Back Splash Guard F. Feed Direction Lever V. Tailstock G. Gear and Belt Cover W. Lead Screw H. Spindle Speed Lever (Alpha) X. S

Resumen del contenido incluido en la página 8

� � � �� � �� � �� � � � �� � � � �� � � � �� � � �� � � � � � � �� � � � �� � � � � � � �� � � �� � � � � � �� � � � � ��� � � � � � � � � �� � � � �� � � � � � � � � � �� � � � � � � �� � �� � � � � � �� � � � � � � �� � �� � �� � � � � � � �� � �� �� � � � � � � � � �� � �� � � � � � � � �� � � � � � � ���� � � � � �� � � � � �� � � � �� � � � � � �� �� � �� �� � � � � � �� � �� � � � � � � �� � � �� � � � � � �� � � � � �� � � � � � � � �� � �� � � � � � �� � � �� � � � � �� � �� � � � � � �

Resumen del contenido incluido en la página 9

� � � � � �� � � � � � � �� � � � �� � � �� � � � � � � � � � ��� ����� ������ �������� ���� ���� � ���� � � � � � � � � � � � � � � � � � � � � � � � � � �� � � � � � � � � � � � � � � � � � � � � � � � � � � � �� ���������� ����� �� ������ ��� ��������� ���� � � � � � � � � � � � � � � � � � � � � � � � � � � � �� � ����� ���� ���������� ��������� ������� ���� � ���������� ������������� ���� ����� ���� �������� ���� ���������� �� � ����������� ���� � � � � � � � � � � � � � � � � � � � � � � �

Resumen del contenido incluido en la página 10

Additional Safety Instructions for Lathes 1. UNDERSTANDING THE MACHINE: Read 8. PREVENTING A CUTTING TOOL/CHUCK and understand this manual before operat- CRASH: Always release automatic feeds ing machine. after completing a job. 2. CLEANING MACHINE: To avoid entangle- 9. AVOIDING STARTUP INJURIES: Make ment and lacerations, do not clear chips by sure workpiece, cutting tool, and tool post hand. Use a brush, and never clear chips have adequate clearance before starting while the lathe is

Resumen del contenido incluido en la página 11

Glossary of Terms The following is a list of common definitions, terms and phrases used throughout this manual as they relate to this lathe and metalworking in general. Become familiar with these terms for assembling, adjusting or operating this machine. Your safety is VERY important to us at Grizzly! Arbor: A machine shaft that supports a cutting Headstock: The major lathe component that tool. houses the spindle and motor drive system to turn the workpiece. Backlash: Wear in a screw or gea

Resumen del contenido incluido en la página 12

SECTION 2: CIRCUIT REQUIREMENTS Grounding 220V Single-Phase In the event of an electrical short, grounding reduces the risk of electric shock. The grounding wire in the power cord must be properly connected to the grounding prong on the plug; likewise, the outlet must be properly installed and grounded. Serious personal injury could occur if you All electrical connections must be made in accor- connect the machine to the power source dance with local codes and ordinances. before you have

Resumen del contenido incluido en la página 13

SECTION 3: SETUP Setup Safety Items Needed for Setup The following items are needed to complete the This machine presents setup process, but are not included with your serious injury hazards machine: to untrained users. Read through this entire manu- Description Qty al to become familiar with • Fork Lift or Hoist (Rated 2000 lbs.) ............ 1 the controls and opera- • Lifting Straps (Rated 2000 lbs.) ................. 1 tions before starting the • Lifting Hooks (Rated 2000 lbs.) .....

Resumen del contenido incluido en la página 14

BB. Cabinet Base Fasteners: Inventory —Hex Bolts M12-1.75 x 40 ........................ 6 —Flat Washers 12mm ............................... 6 — Phillips Head Screws M6-1 x 10 ........... 12 After all the parts have been removed from the — Hex Nuts M6-1 ........................................ 4 boxes, the following items should accompany — Flat Washers 6mm ............................... 12 your machine: Major Components (Figure 3) Qty. B A C A. 6" Three-Jaw Chuck w/Jaws .....................

Resumen del contenido incluido en la página 15

Site Considerations Clean Up The unpainted surfaces are coated with a waxy Floor Load oil to prevent corrosion during shipment. Remove Your lathe is a heavy load distributed in a small this protective coating with a solvent cleaner or footprint. Place this machine on concrete floors citrus-based degreaser such as Grizzly’s G7895 only. The floor MUST be level, or the lathe frame Citrus Degreaser. To clean thoroughly, some and ways may distort over time. parts must be removed. Placement L

Resumen del contenido incluido en la página 16

Mounting to Shop Cabinet Base Floor Assembly We recommend that you bolt your lathe to the Refer to the Base parts breakdown on Page 61 floor. Because floor materials may vary, floor for a detailed illustration and parts identification mounting hardware is not included. Since this is during the following assembly. a precision machine, it is important to level the machine with a precision level when mounting. To assembly the cabinet base: 1. Prepare the lathe location, and drill the holes

Resumen del contenido incluido en la página 17

2. Move the apron toward the right to help bal- Lifting & Moving ance the load, as shown in Figure 8. 3. Position the chip pan on top of the base assembly so that the six lathe mounting holes align with top holes of the cabinets. 4. Un-bolt the lathe from the pallet. 5. Slowly raise the lathe from the pallet, and move it over the cabinet base at your pre- pared location. 6. Position the lathe so that the six M12-1.75 x 40 hex bolts and flat washers can be inserted You will need power liftin

Resumen del contenido incluido en la página 18

Test Run & Break-In NOTICE NEVER shift lathe gears when lathe is operating, and make sure both the half-nut Speed Levers lever and the feed lever are disengaged before you start the lathe! Otherwise the lathe will feed the apron into the chuck or tailstock causing severe lathe damage. The purpose of the test run is to make sure the Figure 11. Headstock controls. lathe and its safety features operate correctly. 7. Push the POWER START button, then move To begin the test run & break-in p

Resumen del contenido incluido en la página 19

4. Attach a lathe dog to the bar stock from Tailstock Setup Step 1 and mount it between the centers (as shown in Figure 13). The tailstock alignment was set at the factory with the headstock. However, we recommend that you take the time to ensure that the tailstock is aligned to your own desired tolerances. To align the tailstock: 1. Center drill a 6'' long piece of bar stock on both ends. Set it aside for use in Step 4. 2. Make a dead center by turning a shoulder to make a shank. Flip t

Resumen del contenido incluido en la página 20

— If the stock is thinner at the tailstock end, 8. Loosen the tailstock lock lever and adjust the the tailstock needs to be moved away from tailstock offset by the amount of the taper the operator by at least the amount of the by turning the adjustment set screw (Figure taper (Figure 15). 16). Turn another 0.010'' off of the stock and check for taper. Repeat as necessary until the desired amount of accuracy is achieved. Adjustment Screw Looking down from above. Figure 15. Adjusting for tai


Manuales de instrucciones similares
# Manual de instrucciones Categoría Descargar
1 Grizzly G0509G Manual de instrucciones Torno 24
2 Grizzly G0516 Manual de instrucciones Torno 18
3 Grizzly G0456 Manual de instrucciones Torno 1
4 Grizzly G0509 Manual de instrucciones Torno 3
5 Grizzly G0584 Manual de instrucciones Torno 2
6 Grizzly G0602 Manual de instrucciones Torno 30
7 Grizzly G0554Z Manual de instrucciones Torno 3
8 Grizzly G0653 Manual de instrucciones Torno 0
9 Grizzly G0624 Manual de instrucciones Torno 0
10 Grizzly G0657 Manual de instrucciones Torno 1
11 Grizzly G0658 Manual de instrucciones Torno 0
12 Grizzly G0657/G0658 Manual de instrucciones Torno 1
13 Grizzly G0698 Manual de instrucciones Torno 2
14 Grizzly G0694 Manual de instrucciones Torno 0
15 Grizzly G0733 Manual de instrucciones Torno 10
16 Edelbrock 1551 Manual de instrucciones Torno 0
17 Bushnell 26-0100/26-0102 Manual de instrucciones Torno 1
18 Delta 46-715 Manual de instrucciones Torno 10
19 Delta 434-08-651-0006 Manual de instrucciones Torno 0
20 Delta 46-705 Manual de instrucciones Torno 0