Resumen del contenido incluido en la página 1
1
2 OPTIONAL ACCESSORIES
SHREDDER KIT
P/N 890209.
Shreds leaves, dramatically
reducing total volume, 12:1.
HEAVY DUTY VACUUM
HOSE KIT
P/N 900998.
4"(102mm) x 7' (2.13m)
For vacuuming in hard to
reach areas.
NOZZLE WEAR PLATES
P/N 890413.
Extends nozzle life when
used along curbs and hard
surfaces.
STANDARD TURF PRO
DEBRIS BAG
P/N 890028.
Standard on TKD models. For
use in leaves and grass in non-
dusty conditions.
OPTIONAL DEBRIS BAGS
PRO FELT BAG
P/N 890023
For use in dusty conditions.
FELT BA
Resumen del contenido incluido en la página 2
5 IN THE INTEREST OF SAFETY BEFORE STARTING ENGINE, READ AND UNDERSTAND THE “ENTIRE OPERATOR'S MANUAL & ENGINE MANUAL.” THIS SYMBOL MEANS WARNING OR CAUTION. DEATH, PERSONAL INJURY AND/OR PROPERTY DAMAGE MAY OCCUR UNLESS INSTRUCTIONS ARE FOLLOWED CAREFULLY. WARNING: The Engine Exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. 21. DO NOT touch hot muffler, cylinder, or 13. DO NOT tamper with governor springs, f
Resumen del contenido incluido en la página 3
9 GENERAL SAFETY For your safety and the safety of others, these directions should be followed: Do not operate this machine without first reading ·DO NOT operate during excessive vibration. owner's manual and engine manufacturer's manual. ·DO NOT remove bag until engine has been turned off and has Use of Ear Protection is recommended while come to a complete stop. operating this machine. ·DO NOT remove hose kit cap on nozzle until engine has been turned off and has come to a complete stop.
Resumen del contenido incluido en la página 4
LITERATURE ASSY P/N 890423 13 13 13 13 13 CONTROLS 12 Owner's Literature Checklist Manual Check Owner's Manual Throttle 890034 Control C Start H Check Literature position Literature O KD / TKD KD / TKD K Accesso- Accesso- E ries 890409 ries Briggs engines have a primer FAST button carburetor Check with no choke. Warranty Warranty Card Card 400972 SLOW Stop STOP Check EU Declaration of position EU Declaration Conformity & EU of Conformity Distributor List & EU 890393 Distributor List 14 15 ENGI
Resumen del contenido incluido en la página 5
16 OPERATION INTENDED USE: This machine is designed for vacuuming CHIPPING OPERATION 16.3 leaves, grass clippings and other types of organic litter and (TKD MODLES ONLY) for chipping brush, limbs, corn and sunflower stalks and palm fronds. Debris mixed with cans, bottles and small amounts of sand Wearing Eye Protection and Durable can be vacuumed; however, it is not this machine's primary Gloves is recommended while operating purpose. Vacuuming cans, bottles and sand will affect the chipper. lo
Resumen del contenido incluido en la página 6
16 OPERATION continued 16.7 DEBRIS BAG Debris bags are normal replaceable wear items. Note: Frequently empty debris to prevent bag overloading with more weight than you can lift. An optional bag and dust cover is available for use where debris will be vacuumed in dusty conditions (see Optional Accessories shown on page 1). DO NOT place bag on or near hot surface, such as engine. Run engine at 1/2 throttle for first 1/2 hour to condition new bag. Your new bag requires a break-in peri
Resumen del contenido incluido en la página 7
16 OPERATION continued 16.4 HANDLING & TRANSPORTING: 16.8 TAMPER-TKD ONLY Before turning machine off, use the Tamper to slowly push Using two people to lift machine is recommended. Lift holding the remaining pieces of wood through the chipper. This can handle and front of nozzle. Secure in place during transport. prevent any remaining wood from jamming in the chipper when machine is turned off. Do not leave tamper on the ground, store tamper in the chipper 16.11 STORAGE hopper. Never store e
Resumen del contenido incluido en la página 8
17 MAINTENANCE CHIPPER BLADE REMOVAL AND SHARPENING-TKD ONLY Use only a qualified mechanic for any adjustments, disassembly or Chipper blades are normal replaceable wear items. any kind of repair . D DANGER ANGER KEEP KEEP HANDS and FEET HANDS and FEET AW AWA AY Y DANGER Chipper blade is sharp. Replace any damaged blade. WARNING: TO AVOID PERSONAL INJURY, ALWAYS TURN MACHINE OFF, MAKE SURE ALL MOVING Depending on the type and amount of wood being chipped, the PARTS COME TO A COMPLETE STOP. c
Resumen del contenido incluido en la página 9
17 MAINTENANCE continued IMPELLER REMOVAL continued 17.1 17.3 DRIVE Chains are normal replaceable wear items. A new chain 18. If chipper blade properly clears anvil surface, proceed to step . should not be used on worn sprockets. Sprockets should be If not, return to (step 14) and add or subtract shim washers as replaced when replacing chains. needed to obtain a correct gap. Stop engine and disconnect spark plug 19. Reinstall engine and impeller onto housing in reverse order wire before m
Resumen del contenido incluido en la página 10
18 PARTS DRAWING KD511SP, TKD511SP Page 10 of 12 Part No. 890034 Form No. F101000A
Resumen del contenido incluido en la página 11
ITEM KD511SP TKD511SP 19 NO. Description Part No. Qty. Part No. Qty. 1 Debris Bag Turf (service) 890023 1 890028 1 PARTS 2 Throttle Assembly (INCL. 1 ea. 4,10) 900514-04 1 900514-04 1 3 Tamper - - 890229 1 LIST 4 Nut Lock (1/4 - 20) *8160001 10 *8160001 12 * Denotes 5 Screw Cap (1/4 - 20 x 1- 1/2 HEX) *8041008 4 *8041008 4 standard 6 Handle Assy' (incl. items 4(6), 5(4), 11(2), 75(2), 76 & 99) 900057 1 900059 1 hardware 7 Axle Rear - Frame W.A. 890389 1 890389 1 item that 8 Screw Handle 5/16
Resumen del contenido incluido en la página 12
Item KD511SP TKD511SP Description Qty. Qty. 19 No. Part No. Part No. 86 Wheel With Sprocket Ass'y Cast ( 21, 94, 95, 96) 890242 2 890242 2 * Denotes PARTS LIST 87 Chain 52 Pitch 890239 2 890239 2 standard 88 Chain 40 Pitch 900323 1 900323 1 hardware 89 Washer Flat 5/16 (3/8 ID x 7/8 x 1 1/6) *8171003 4 *8171003 4 ( Continued from item that 90 Bolt Carriage 5/16 - 18 x 3/4 *8024039 4 *8024039 4 page 11 ) 91 Washer Spring Lock 5/16 *8177011 4 *8177011 4 may be 92 Nut Regular 5/16 - 18 *8142002
