Resumen del contenido incluido en la página 1
OPERATOR’S MANUAL
ENGINE DRILL
EDR-210
WARNING
READ INSTRUCTIONS CAREFULLY AND FOLLOW RULES FOR
SAFE OPERATION.
FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY.
ECHO POWER EQUIPMENT(CANADA)
501 Newbold Street, London, Ontario Canada N6E 1K4
X750-004 72 3
X750409-3303
Printed in Japan 0906Ap 0389 ES
Resumen del contenido incluido en la página 2
This spark ignition system complies with Canadian ICES-002. Copyright © 2002 All Rights Reserved.
Resumen del contenido incluido en la página 3
INTRODUCTION ECHO Engine Drill EDR-210 is a lightweight, high performance, two-stroke engined unit designed for WARNING drilling. IMPROPER USE OR CARE OF THIS UNIT, OR FAILURE TO WEAR PROPER PROTECTION This Manual provides the information necessary CAN RESULT IN SERIOUS INJURY. READ for operation and maintenance. AND UNDERSTAND THE RULES FOR SAFE OPERATION AND ALL INSTRUCTIONS IN THIS MANUAL. SAFETY AND SPECIAL INFORMATION CIRCLE AND SLASH SYMBOL DANGER This symbol means the specific action
Resumen del contenido incluido en la página 4
SAFETY WARNING WARNING ENGINE DRILL USERS RISK INJURY TO ALWAYS STOP THE ENGINE WHEN A DRILL THEMSELVES AND OTHERS IF THE ENGINE JAM OCCURS. DO NOT ATTEMPT TO DRILL IS USED IMPROPERLY, AND/OR REMOVE AN OBJECT CAUSING A DRILL SAFETY PRECAUTIONS ARE NOT JAM IF THE ENGINE IS RUNNING. PHYSICAL FOLLOWED. PROPER CLOTHING AND INJURY CAN OCCUR IF A DRILL JAM IS SAFETY GEAR MUST BE WORN WHEN REMOVED AND THE DRILLS START OPERATING ENGINE DRILL. MOVING. • Do all drilling at full throttle speed. Drilli
Resumen del contenido incluido en la página 5
� Wear non-slip, heavy-duty work gloves to improve your grip on the engine drill handles. WARNING The gloves also help reduce the transmission PRECAUTION AGAINST VIBRATION of machine vibrations to your hands. AND COLD IT IS BELIEVED THAT A CONDITION PROTECTING OTHERS CALLED RAYNAUD’S PHENOMENON, Spectators, children, fellow workers and animals WHICH AFFECTS THE FINGERS OF must be warned to come no nearer than 4.6 m CERTAIN INDIVIDUALS MAY BE BROUGHT while the engine drill is in use. ABOUT BY E
Resumen del contenido incluido en la página 6
Repetitive Stress Injuries It is believed that over-using the muscles and tendons of the fingers, hands, arms and shoulders may cause soreness, swelling, numbness, weakness and extreme pain in those areas. Certain repetitive hand activities may put you at a high risk for developing a Repetitive Stress Injury (RSI). An extreme RSI condition is Carpal Tunnel Syndrome (CTS), which could occur when your wrist swells and squeezes a vital nerve that runs through the area. Some believe that prolonged e
Resumen del contenido incluido en la página 7
OPERATING TECHNIQUES � When starting to drill, run the engine at full � When transporting or storing the machine throttle. always remove the drill bit. � To reduce fire hazard keep engine and silencer WARNING free of debris, leaves or excessive grease. BEFORE DRILLING, BE SURE TO READ AND � Handle drill with care, contacting with drills UNDERSTAND THE ENTIRE OPERATOR’S may cause injury. MANUAL TO AVOID THE CHANCE OF SERIOUS INJURY. � Do not force the drills and only move as quickly as the dri
Resumen del contenido incluido en la página 8
DESCRIPTION 2 Part Number 890317-05560 1 3 4 Part Number X505-002310 14 15 Part Number X505-002570 13 Part Number X505-002310 12 11 10 Part Number X505-002570 9 7 6 8 5 * If a decal cannot be read, a new one can be ordered from your ECHO dealer. 1. Operator’s manual - Included with unit. Read 9. Fuel tank - Contains fuel and fuel filter. before operation and keep for future reference 10. Fuel tank cap - For closing the fuel tank. to learn proper, safe operating techniques. 11. Air cleaner c
Resumen del contenido incluido en la página 9
ASSEMBLING FRONT HANDLE • Insert the front handle to the machine, and turn clockwise. (TIGHTEN THE SCREW FIRMLY) Washer - To operate front handle with right hand, remove right plug then reverse sides when Front handle installing handle and plug. DRILL BIT � Insert the drill bit (not provided with unit) until it reaches the bottom of the chuck, then back it out slightly; tighten the chuck laws evenly and completely. IMPORTANT Use drill bits suited for the material being drilled and for the depth
Resumen del contenido incluido en la página 10
IMPORTANT � ECHO premium Power Blend X™ Universal 2-Stroke Oil may be mixed at 50 : 1 ratio for application in all ECHO engines sold in the past regardless of ratio specified in those manuals. � Use of unmixed, improperly mixed, or fuel older than 90 days, (stale fuel), may cause hard starting, poor performance, or severe engine damage and void the product warranty. Read and follow instructions in the Storage section of this manual. HANDLING FUEL MIXING INSTRUCTIONS - 1. Fill an approved fuel co
Resumen del contenido incluido en la página 11
STARTING COLD ENGINE WARNING WHEN ENGINE IS STARTED, CONFIRM IF THERE IS NOT ANY ABNORMAL VIBRATION OR SOUND. IF THERE IS ABNORMAL VIBRATION OR SOUND, ASK YOUR DEALER TO REPAIR. � Stand the engine upright on a level surface. � Place ignition switch in ON (START/RUN) ON position. Ignition switch � Push purge bulb 3 to 4 times (or until fuel is STOP visible in fuel return line). � Shift choke lever to close position (START). Throttle trigger � Pull starter handle until the engine fires. Thrott
Resumen del contenido incluido en la página 12
REVERSE ROTATION � This model is equipped with reverse rotation mechanism. Counter � When drilling, set shift lever down to clockwise clockwise (CW) rotation position. (CCW) � If bit is locked due to deep penetration during drilling operation, set shift lever up to counterclockwise (CCW) rotation position and operate reversed for easy pulling-out. � When changing direction of drill rotation, Clockwise operate as follows: Shift lever (CW) - Return engine to idle. - Engine shift lever to CW or CCW
Resumen del contenido incluido en la página 13
MAINTENANCE AND CARE AREA MAINTENANCE PAGE BEFORE MONTHLY YEARLY DATE USE MAINTENANCE PERFORMED Air Filter Clean/Replace 13 � Fuel Filter Inspect/Clean/ Replace 13 � Spark Plug Inspect/Clean/ Adjust/Replace 13 � Carburetor Adjust 14 � Cooling System Inspect/Clean 15 � Silencer Inspect/Tighten/Clean 15 � Starter Rope Inspect/Replace - � Drills Inspect/Clean/ Lubricate - � Fuel Leaks Inspect 13 � Screws, Bolts and Inspect, Nuts Tighten/Replace - � Fuel Line Inspect - � IMPORTANT Time intervals are
Resumen del contenido incluido en la página 14
TROUBLE SHOOTING Trouble Engine - hard to start Cause Remedy - does not start Engine Fuel at No fuel � Fuel filter clogged � Clean or replace cranks carburetor at carburetor � Fuel line clogged � Clean � Carburetor � Ask your ECHO dealer Fuel at No fuel at � Carburetor � Ask your ECHO dealer cylinder cylinder Silencer wet � Fuel mixture is too rich � Open choke with fuel � Clean/replace air filter � Adjust carburetor � Ask your ECHO dealer Spark at No spark at � Ignition switch off � Turn switc
Resumen del contenido incluido en la página 15
MAINTENANCE AIR FILTER � Clean before use. - Remove air cleaner cover and pull out air filter. - Lightly brush off dust or wash it in water and detergent. - Dry completely before putting it back in Air filter place. Air cleaner cover FUEL FILTER � Check periodically. - Do not allow dust to enter into fuel tank. - Clogged filter will cause difficulty in starting engine or poor engine performances. - Pick up fuel filter through fuel inlet port with a piece of steel wire or the like. Fuel filter -
Resumen del contenido incluido en la página 16
REPLACEMENT OF CHUCK Replacement of chuck should be done in the following manner: 1. Remove bolt with hexagonal hole fixed in the driving axle. 2. Insert accessory hexagonal bar (Part Number 895412-20960) into chuck and fix. 3. Fit 19 mm spanner onto driving axle and keep it fitted. 4. Fit 10 mm box spanner onto the hexagonal bar and turn it into direction as indicated by an arrow to remove chuck. 5. Fit a new chuck in the reversed order of removing. Hexagonal bar (Part Number 895412-20960) Box
Resumen del contenido incluido en la página 17
CLEANING CYLINDER FINS CLEANING SILENCER AND (Check Periodically) EXHAUST PORT (Check Periodically) NOTE 1. Carefully remove housing halves. Clogged fins will cause poor engine cooling. 2. Remove and disassemble silencer. 1. Carefully remove housing and clean dirt and NOTE dust from fins. Be careful not to scratch the cylinder or piston 2. Reinstall housing. when cleaning the cylinder exhaust port. 3. Clean deposits from cylinder exhaust port and silencer. STORAGE 6. Drain the fuel tank complete
Resumen del contenido incluido en la página 18
SPECIFICATIONS EDR-210 Mass without drill bit kg 4.6 (10.1 lbs ) Volume fuel tank L 0.5 (16.9 US, fl. oz.) Drill size mm 32 - 178 (1.25 - 7 inch) chuck capacity mm 13 (0.5 inch) speed r/min 520 Mission reduction ratio 17.1 (regular side) 18.6 (reverse side) lubrication grease External Dimensions length × width × height mm 430 × 320 × 265 without drill bit (16.9 × 12.6 × 10.4 inch) Engine type Air cooled Two stroke single cylinder engine displacement mL(cm³) 21.2 (1.29 cu. inch) recommended maxim
