Resumen del contenido incluido en la página 1
®
5 HORSEPOWER
3 CUTTnNG STAGE
MULCHING AND BAGGING
Caution:
CHiPPER-SHREDDER
ReadandFollow
All SafetyRules
andInstructions
Assembly
BeforeOperating
Operation
ThisEquipment
CustomerResponsibilities
ServiceandAdjustment
RepairParts
60195U.S.A.
SEARS,ROEBUCK ANDCO.,HoffmanEstates,iL
770-7110H 9192
Printed in U.S.A.
(R920818)
Resumen del contenido incluido en la página 2
SAFETY RULES WARNING: TO REDUCE THE POTENTIAL FOR ANY INJURY, COMPLY WITH THE FOLLOWING SAFETY INSTRUCTIONS. FAILURE TO COMPLY WITH THE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY. TRAINING e If the cutting mechanism strikes any foreign object or if your machine should start making an unusual noise or e Read this owner's manual carefully in its entirety before vibration, immediately stop the engine, disconnect the attempting to assemble or operate this machine+ Be com+ spark plug wire from the sp
Resumen del contenido incluido en la página 3
CONGRATULATIONS on your purchase of a Sears PRODUCT SPECaFICATIONS Craftsman Chipper-Shredder,, It has been designed, engi- neered and manufactured to give you the best possible Horsepower: 5°0 dependability and performance_ Should you experience any problem you cannot easily rem- Displacement: 12.57 cuo in. edy, please contact your nearest Sears Service Center/ Department in the United States., We have competent, welt- Fuel Capacity: 3 Quarts trained technicians and the proper tools to service
Resumen del contenido incluido en la página 4
iii i ,UU,lU,i i i, i,ii TABLE OF CONTENTS ,,u, STORAGE ................................................................................... 13 SERVICE AND ADJUSTMENT ..................................... 13-!5 TROUBLE SHOOTING ..................................................... 16 REPAIR PARTS--CHIPPER-SHREDDER ........ 17, 18 REPAIR PARTS--ENGINE ....................................... 19-23 PARTS ORDERING/SERVICE .....................................16 i i,,i lUl INDEX i ii,u , u, A 0 Oil ..
Resumen del contenido incluido en la página 5
ASSEMBLY INSTRUCTIONS = i i1,1111,1,1,111,1iii iiiii1,111111[111111111111111111111111111111111 IMPORTANT: This unit is shipped WITHOUT GASO- 3 £ LINE or OIL, After assembly, see operation section of this manuat for proper fuel and engine oil recommen- dations NOTE: To determine right and left hand sides of your Flat ""__ chipper-shredder, stand behind and face the hopper (engine is at the front of the unit), Washer | _ ) 5/16 LD. Your chipper-shredder has been completely assem- bled at the facto
Resumen del contenido incluido en la página 6
Housing HOWTO SET-UPYOURCHIPPER-SHREDDER MAKE CERTAIN THE SPARK PLUG Bolt AWAY FROM THE SPARK PLUG WIRE IS DISCONNECTED AND MOVED Chute BEFORE ASSEMBLING THE CHIPPER,_ SHREDDER. Hex -
Resumen del contenido incluido en la página 7
string,andputtonthedrawstring untiltile bagistight ® To attachthe bag,placethe openingof the bag aroundthechuteopening.. Release plungerto lockit overthechutedeflector soit completely coversthe chuteopeningDepresstheplungeron thedraw- intopositionSeefigure5. ................................... ii, i ,lllllll,lll ,IIIIHIIII OPERATION i iii ii ii ,i ii ,i KNOW YOUR CHIPPER-SHREDDER READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR CHIPPER-SHREDDER. Compare the illustrations with your
Resumen del contenido incluido en la página 8
No Larger Than TO STOP EHGIHE 1/2" Diameter ® Move throttle control lever to OFF position. See fig- Recommended) ure6° Or 1" Diameter (Maximum) ® Disconnect spark plug wire and move away from spark plug to prevent accidental starting while equipment is unattended_ HOW TO USEYOUR CHIPPER-SHREDDER Do not attempt to shred or chip any materiat other than vegetation found in a normal yard (Leo, branches, \ leaves, twigs, etc_)+ Hopper Assembly WARNING: THE CHIPPER-SHREDDER FIGURE 7. DISCHARGES MATERI
Resumen del contenido incluido en la página 9
e To lower the hopper assembly, use one hand to GASAND OIL FILL-UP grasp the handle at the top of the hopper assembly OIL and lift slightly Pull up on the release bar, and lower the hopper' assembly to the ground.. Release Only use high quality detergent oil rated with API set- the bar. See figure t0. vice classification SG. Select the oil's viscosity grade according to your expected operating temperature. Hopper Assembly Colder -,_ 32°F _ Warmer 5W30 _ SAE 30 NOTE: Although multi-viscosity oils
Resumen del contenido incluido en la página 10
Check the fuel level periodically to avoid running out ® Attach spark plug wire and rubber boot to spark of gasoline while operating the chipper-shredder. If plug if necessary. See figure 13. the unit runs out of gas as it is shredding or chipping, ® Place the throttle control lever in FAST position_ it may be necessary to unclog the unit before it can be See figure 14.. restarted.. Refer to "Removing the Flail Screen" in e Move choke lever to CHOKE position° SERVICE AND ADJUSTMENT section_ • Gr
Resumen del contenido incluido en la página 11
IIIINIIIIIlUlIIIlUlU lUllU II IllUU ' II " II II U II II I' " II I' III I' I CUSTOMER RESPONSIBILHTHES 1,1,11,1 M iiii MAINTENANCE SCHEDULE FILL IN DATES AS YOU COMPLETE REGULAR SERVICE ,ul i,i, I-- o Oil Pivot Points ",J O rr Clean Shredder .,/ _/ a. Check Engine Oil q Change Engine Oil 4 4 Service Air Cleaner 4 ,/ ,7 z Clean Engine Cylinder 4 4 Spark Plug Muffler 4 ,,/ CHECK GENERAL RECOMMENDATIONS NOTE: Although multi-viscosity oils (SE30, 10W30, etc,) improve starting in cold weather, these
Resumen del contenido incluido en la página 12
AIR CLEANER WARNING: PERIODICALLY CLEAN MUF- The air cleaner prevents damaging dirt, dust, etc. FLER AREA TO REMOVE ALL GRASS, from entering the carburetor and being forced into the DIRT AND COMBUSTIBLE DEBRIS. engine and is important to engine life and per- formanceo Never run your engine without air cleaner com- CLEANING pletely assembled. e The chipper-shredder may be cleaned by running To Service Air Cleaner: water from a hose through the hopper assembly Service pre_cleaner after every 25 ho
Resumen del contenido incluido en la página 13
u =, in u l STORAGE e Drain the fuel tank, Prepare your chipper-shredder for' storage at the end of the season or if the unit will not be used for 30 days ® Start the engine and let it run until the fuel lines and or more,, carburetor are empty e Never use engine or carburetor cleaner products in WITH FUEL IN THE FUEL TANK INSIDE the fuel tank or permanent damage may occur, WARNING: NEVER STORE MACHINE OF BUILDING WHERE FUMES MAY e Use fresh fuel next season REACH AN OPEN FLAME OR SPARK, OR NOTE
Resumen del contenido incluido en la página 14
Chute Replace or sharpen blades. If sharpening, make cer- Hairpin \ tain to remove an equal amount from each blade Clips, Reassemble in reverse order. Clevis Pins Make certain blades are reassembled with the sharp edge facing the direction shown in figure 19 (sharp edge is assembled toward the slotted opening in the impeller assembly). _-_Hex SHREDDING BLADE Nuts. The shredding blade may be removed for sharpening Washers 4 Screen or replacement as follows. e Disconnect spark plug wire and move i
Resumen del contenido incluido en la página 15
NOTE: Usecaution whenremoving thebladeto avoid The carburetor may need re-adjusting if engine lacks contacting theweldboltsonthehousing. power or does not idle properly If adjustments are needed, proceed as follows. ® Whensharpeningthe blade,followthe original e Close needle valve (see figure 22) clockwise angleof grindasa guide.It isextremely important ((-_) finger tight only. Forcing may cause damage thateachcutting edgereceives anequalamountof Then open 1-1/2 turns counterclockwise (v'_). gri
Resumen del contenido incluido en la página 16
TROUBLE SHOOTING PROBLEM CORRECTIVE ACTION Engine faits to start e Fuel tank empty, or stale fuel, • Fill tank with clean, fresh fuel ® Spark plug wire disconnected. e Connect wire to spark plug. • Faulty spark plug. e Clean, adjust gap or replace. Loss of power; e Spark plug wire loose. • Connect and tighten spark plug wire operation erratic • Unit running on CHOKE. e Move choke lever to OFF position. ® Blocked fuel line or stale fuel • Clean fuel fine; fill tank with clean fresh gasoline, • Di
Resumen del contenido incluido en la página 17
SEARS CRAFTSMAN 5 H.P. CHIPPER-SHREDDER MODEL NOS. 247.797854 Repair Parts 247.797855 19 !3 44 / 3 tt 57 17
Resumen del contenido incluido en la página 18
SEARS CRAFTSMAN 5 H.P. CHIPPER-SHREDDER MODEL NOS. 247.797854 Repair Parts 247.797855 KEY PART PART DESCRIPTION KEY DESCRIPTION NOo NOo NO. NO, 1 Blade 37 742-057I 710-0157 Hex Bolt 5/16_24 x ,75" Lg,, 2 710-0818 736_0119 L-Wash, 5/16" I.D,* Hex Patch Bolt 3/8-24 x 2" Lg_ 38 710_3008 (Gro 8) (247.797854) 39 Hex Bolt 5/16-18 x °75" Lgo 710-1254 Hex Patch Bolt 3/8-24 x (Gr_ 5) 2,25" Lg, (247.797855) 40 Hex Bolt 5/16-18 x 1,5" Lg,,* 714-0t14 681-0004 Sq. Key 1/4 x 2°0" Lg° 41 Flail Housing Ass'y.--
Resumen del contenido incluido en la página 19
BRIGGS AND STRATTON 5 H.P. ENGINE MODEL NOS. 135212-0272-01 Repai r Parts 135212-0140-01 REFo PART 373 NOo NO, DESCRIPTION 55 494846 Housing-Rewind Starter 56 493824 Pulley-Rewind Starter 57 262594 Spring-Rewind Starter 55 58 280406 Rope-Rewind Starter Cut to Required Length 59 396892 Insert-Starter Handle 60 393152 Handle-Rewind Starter 65 94686 Screw-Housing Mtg. 69 280973 Washer 69A 224322 Washer 373 92987 Nut-Hex, 456 224321 Retainer 58 459 492833 PawI-Starter 461 262626 Pin-Spring 515 26262
Resumen del contenido incluido en la página 20
BRIGGS AND STRATTON 5 H.P. ENGINE MODEL NOS. 135212-0272-01 135212-0140-01 Repair Parts i i J lU,U 634 97 _202 REF, PART NO, DESCRIPTION NOo 52 *'27t936 Gasket-Carburetor Mounting (2) 90 495426 Carburetor Assembly 95 93499 Screw*Throttle Valve to Shaft 96 223793 Throttle-Carburetor 97 490048 Shaft and Lever-Throttle 108 491177 Valve & Shaft Group-Choke Valve-Needle 118 231533 Screw-Hex. Head t24 94616 127 220352 Plug-Welch 127A 223789 Plug-Welch 149 26336 Spring-Needle Valve 152 260575 Spring-Th