Resumen del contenido incluido en la página 1
®
Stealth dc
C45GxxxB
O W N E R ’ S M A N U A L
Resumen del contenido incluido en la página 2
THIS WARRANTY SUPERSEDES ALL ® PREVIOUS WARRANTIES Stealth DC If purchased from our authorized dealer, this ceiling fan is warranted to the original purchaser by Casablanca Fan Company against defects in materials and workmanship for the following: Motor excluding Electronics ������������������������������������������������������������������������������������������������������������������������������������������Lifetime Component Parts, Electronic or Manual
Resumen del contenido incluido en la página 3
® Stealth dc Owner’s Manual READ AND SAVE THESE INSTRUCTIONS! Safety and the proper operation of your Casablanca fan both require a thorough knowledge of the product and proper installation; therefore, before attempting to install and operate your Casablanca fan, read this owner’s manual completely and carefully. Retain this manual for future reference. CAUTION: To avoid possible electrical shock, make certain that electricity is turned off at the circuit breaker or fuse box before attemptin
Resumen del contenido incluido en la página 4
Parts List Model # C45G11B C45G695B C45G45B Asm. Dwg. # G1173-01 G1173-02 G1173-03 1 3 4 Parts List Finish Snow White Alpha Bronze Brushed Nickel Item # Item Name Qnty Part # Part # Part # 1 Ceiling Plate 1 77766-01-000 77766-01-000 77766-01-000 6 7 5 Hanging System 1 77746-03-203 77746-02-695 77746-01-214 3 Canopy 1 4 Canopy Hatch 1 11 10 5 3/8” Lag Screw 1 9 8 6 3/8” Flat Washer 1 7 #8-32 Truss Screw (Ceiling Plate) 2 8 #8 Flat Washer 2 12 9 #8 Split Lockwasher 4 10 #8-32 round Screw (Canopy
Resumen del contenido incluido en la página 5
® s L eat th dc Model # C45G11B C45G695B C45G45B Asm. Dwg. # G1173-01 G1173-02 G1173-03 Parts List Finish Snow White Alpha Bronze Brushed Nickel Item # Item Name Qnty Part # Part # Part # 1 Ceiling Plate 1 77766-01-000 77766-01-000 77766-01-000 Hanging System 1 77746-03-203 77746-02-695 77746-01-214 3 Canopy 1 4 Canopy Hatch 1 5 3/8” Lag Screw 1 14 15 6 3/8” Flat Washer 1 7 #8-32 Truss Screw (Ceiling Plate) 2 8 #8 Flat Washer 2 9 #8 Split Lockwasher 4 17 16 10 #8-32 round Screw (Canopy Screw)
Resumen del contenido incluido en la página 6
PLEASE INSPECT ALL PACKAGING PRIOR TO DISCARDING! Your Casablanca fan was crafted with pride and care and inspected thoroughly prior to shipment. Before you begin to assemble and install your Casablanca fan, remove all parts from the carton and check them against the Parts Guide in this manual. Make sure all parts are included in the box using the Parts Guide on the following pages. If there are missing or broken parts: Always turn power to the ceiling fan OFF before Call 1-888-227-2178 Mond
Resumen del contenido incluido en la página 7
® s eaL t th dc INTRODUCTION BEFORE YOU START • CAUTION: RISK OF ELECTRICAL SHOCK! Installation is to be in accordance with the National Electrical Code, ANSI/NFPA 70-1999 and local codes. If you are unfamiliar with the wiring codes, you should use a qualified electrician. To avoid overheating and possible damage to other equipment, do not install control to a receptacle, fluorescent light fixture, motor-operated appliance, or transformer-supplied appliance. • This fan is designed to be
Resumen del contenido incluido en la página 8
MOUNTING RECOMMENDATIONS Before mounting your Casablanca fan, read the following helpful recommendations. The location of the fan, air circulation, and fan size are all important factors to consider before installation. Location Ceiling fans have practical uses in almost every room in your home. We suggest you follow these mounting recommendations as you decide where to install your Casablanca fan. • For safety reasons, the fan blades must be a minimum of 7' above the floor. • Do not loca
Resumen del contenido incluido en la página 9
® s eaL t th dc FAN INSTALLATION GETTING STARTED Installing a New Ceiling Fixture Outlet Box Using Existing Ceiling Fixture Outlet Box If you do not have an existing fixture located After turning the power OFF at its source (either where you wish to place your Casablanca fan, the circuit breaker or fuse box), lower the old an approved ceiling fixture outlet box must be fixture and disconnect the wiring. Check the installed and wired. ceiling fixture outlet box to be sure it is marked “A
Resumen del contenido incluido en la página 10
MOUNTING BRACKET INSTALLATION (CONT.) Step 1. Place a flat washer on each of the two screws that came with the outlet box and pass the screws through the slotted holes in the ceiling plate into the screw holes in the outlet box. Ceiling Fan Step 2. Tighten the screws into the outlet box; Approved do not use lubricants on the screws. Do not over Wiring Box tighten. Joist Washer Outlet Box Screw NOTE: Lag Screw installation is required only under two conditions: • Fan weighs 36 lbs. or m
Resumen del contenido incluido en la página 11
® s eaL t th dc CANOPY HARDWARE Canopy Canopy Screws and (4) Lock Phillips Canopy Hatch Washers Screwdriver CANOPY INSTALLATION Step 1. Attach the canopy to the ceiling plate with 1 three of the 8-32 x 2 /2" long canopy screws and lock washers provided with your Casablanca fan. Tighten using the provided screwdriver until snug against the ceiling. Canopy NOTE: On sloped ceilings, align the canopy opening with the top or peak of the room. Canopy Screw Lock Washer HANGING HARDWARE All
Resumen del contenido incluido en la página 12
MOTOR WIRES (LEAVE AT LEAST Step 2. Route the wires through the 3" 6" LONG) Perma•Lock downrod and ball assembly as shown in Figures #3. Insert the downrod into the motor coupling and turn it clockwise until it stops turning, PERMA•LOCK™ DOWNROD AND ensuring that the pole has bottomed out. BALL ASSEMBLY Step 3. Tighten the set screw using the provided allen wrench. MOTOR TAPERED COUPLING THREAD Tip: The downrod has a tapered thread that MOTOR is designed to lock completely when inst
Resumen del contenido incluido en la página 13
® s eaL t th dc HANGING THE FAN Step 1. To hang the fan body in the canopy, hold the fan body firmly and insert the ball into the canopy opening as in Figure #1. Check that no wires are pinched. Rotate the fan body until the slot in the ball fits into the pin opposite the canopy opening in Figure #2. MOTOR HOUSING ASSEMBLY FIGURE 1. Pin Slot FIGURE 2. CANOPY ELECTRICAL CONNECTIONS Step 2. Trim excess motor wires, leaving at least 6 inches above the downrod. Strip 1/2-inch insulation
Resumen del contenido incluido en la página 14
CANOPY HATCH INSTALLATION Step 1. Tuck the wires into the canopy with the wire nuts pointed upwards, so that the WHITE and BLACK wires are on opposite sides of the canopy and all wires are clear of the canopy opening. Step 2. Install the canopy hatch with the last canopy screw and lock washer using the provided screwdriver. To do this, tilt the fan body away from the hatch opening. Tighten the screws Figure 4. Step 3. Straighten the fan, then check to ensure FIGURE 4. there is no movement
Resumen del contenido incluido en la página 15
® s eaL t th dc BULB INSTALLATION Step 1. Screw the 100-watt Halogen bulb into the socket. Figure 1. Do not touch the glass bulb with your fingers–it is extremely important that the glass be clean. If it is touched, or dirty, clean carefully with a tissue. A dirty glass bulb will cause the bulb to fail almost immediately. IMPORTANT! When installing the halogen bulb, carefully cut off the end of the plastic sleeve the bulb comes in and hold the bulb by the plastic sleeve to screw it int
Resumen del contenido incluido en la página 16
ON D ON D ON D DC Control CHANGING FREQUENCY SETTING You will have to change the dip switch settings in the remote if you are using more than one fan in the same area and want to control them separately. Step 1. At the circuit breaker or fusebox, turn the power off for the fan you want to change. ON ECE Step 2. Open the battery compartment door of the remote 1 2 3 4 control and remove the battery. Step 3. Change the dip switch settings, assuring that they SET are differ
Resumen del contenido incluido en la página 17
DC Control OPERATION SPEED CONTROL There are six individual speed settings for the fan. Each speed is indicated by the number on the controller. To properly calibrate all speeds of the motor, run the fan on speed "6" for 90 seconds after each AC power reset. To select the desired fan speed: Press the number on the controller corresponding to the speed desired. is off. Note: It is normal for the fan to start in the "High" position from "Off" before changing to the selected speed. OPERATION
Resumen del contenido incluido en la página 18
DC Control TROUBLESHOOTING TIPS Please refer to this troubleshooting guide before requesting service or contacting your dealer for assistance. PROBLEM POSSIBLE REMEDIES Fan will not start • Check the main circuit fuses, circuit breakers, and wall switch position. Check all wire connections. Make sure the power is turned off during this inspection. • Pin connectors are not making good contact. Check all connections. • The fan receiver is defective. Replace the fan receiver. • Reset the freq
Resumen del contenido incluido en la página 19
® s eaL t th dc PRODUCT SPECIFICATIONS ® Model Name: Stealth DC Motor: DC Model Number: C45GxxxB Blade Span: 54" Blade Iron Pitch: 14° Dimensions: A = 10.8" No. of Blades: 5 B = 13.25" Technology: DC Control C = 3" NOTE: Dimension B Lightbulb: (1) 100-watt halogen lightbulb includes light fixture D = 11.5" and glass. E = 5.6" Airflow: 6,553 cfm Weight: 33 lbs. Electricity Use*: 30 watts Airflow Efficiency*: 218.46 cfm/watt * Performance data is for fan
Resumen del contenido incluido en la página 20
7130 GOODLETT FARMS PKWY. SUITE 400 MEMPHIS, TN 38016 1 (888) 227-2178 WWW.CASABLANCAFANCO.COM PN C4543001_DC
