Resumen del contenido incluido en la página 1
Quick Start Guide
®
Wireless PnP
LabelManager
Resumen del contenido incluido en la página 2
Copyright © 2013 Sanford, L.P. All rights reserved. No part of this document or the software may be reproduced or transmitted in any form or by any means or translated into another language without the prior written consent of Sanford, L.P. Trademarks DYMO, DYMO Label, and LabelManager are registered marks in the US and other countries. All other trademarks are the property of their respective holders.
Resumen del contenido incluido en la página 3
Quick Start Guide ® ® This guide describes some of the features of your DYMO LabelManager Wireless PnP label maker. Read the following sections for information about using your label maker. Registering Your Label Maker Getting to Know your Label Maker Inserting the Battery Pack Removing the Battery Pack Inserting the Label Cassette Connecting the Label Maker to your Computer Starting the Built-In Software Printing Labels with the Built-In Software Checking the Label Maker Sta
Resumen del contenido incluido en la página 4
Getting to Know your Label Maker Become familiar with the features shown in the following figure. Power button/ Cutter status light Serial number Wireless Battery status light compartment Label exit slot Side cover Cleaning tool Label Back View compartment Reset button USB port Figure 1 2
Resumen del contenido incluido en la página 5
Inserting the Battery Pack The label maker is powered using a rechargeable lithium-ion polymer (LiPo) battery pack. Make sure the USB cable is disconnected before handling the LiPo battery pack. To insert the battery pack 1 Press and pull to open the side cover of the label maker. 2 Insert the battery pack into the battery compartment as shown in Figure 2. Make sure to read the LiPo Safety Precautions found on Press page 12. and pull Removing the Battery Pack Figure 2 Remove the batte
Resumen del contenido incluido en la página 6
Inserting the Label Cassette Your label maker uses DYMO D1 label cassettes. To insert the label cassette 1 Press and pull to open the side cover of the label maker. 2 Make sure the tape and ribbon are taut across the mouth of the cassette and that the tape passes between the label Press and pull guides. See Figure 3. If necessary, turn the ribbon Ribbon rewind Label guides spool rewind spool clockwise to Figure 3 tighten the ribbon. 3 Insert the cassette and press firmly until the ca
Resumen del contenido incluido en la página 7
Connecting the Label Maker to your Computer The label maker connects to your computer through the USB connection located on the back of the label maker. To connect the label maker to your computer 1 Plug one end of the USB cable into the label maker. See Figure 5. 2 Plug the other end into an available, powered USB port on your computer. The label maker must be connected to a powered USB port. The label maker may not charge Figure 5 or function properly when connected to a non- powered US
Resumen del contenido incluido en la página 8
Printing Labels with the Built-In Software The following figure shows some of the features available in the software. Change the units of Start advanced Choose to print Add a border Capture an area of the measure or DYMO Label v.8 a horizontal or around the label. screen and insert on language settings. software. vertical label. your label. Insert text from Manage the the Clipboard. label maker on your wireless network. Create a new label. Select the font, size, and Rotate images 90 style
Resumen del contenido incluido en la página 9
Checking the Label Maker Status The label maker status is displayed in the software window. The following table describes the possible states of the label maker. See Figure 6 on page 6. Label maker is connected; battery pack is charging Label maker is connected; battery pack is not charging Label maker is not connected or is turned off Label maker is connected; there is a problem with the battery pack Charging the Battery Pack You can charge the battery pack by connecting the label mak
Resumen del contenido incluido en la página 10
To charge the battery using the wall adapter 2 1 Insert one end of the USB cable into the label maker. 2 Insert the other end of the USB cable into the wall 1 charger. See Figure 7. 3 Plug the wall adapter into a working power outlet. 4 If the label maker is turned off, press the power button to turn the label maker on and start charging the battery pack. Figure 7 Configuring the Label Maker as a Wireless Printer You can use your label maker either as a local printer connected to a powered
Resumen del contenido incluido en la página 11
To configure the printer on your wireless network Wireless 1 From within the built-in software, click . status light The Wireless Setup tool starts. 2 Follow the steps in the Wireless Setup tool. The wireless status light located on the top of the label maker turns solid blue when the label maker is successfully connected to a wireless network. See Figure 8. 3 After configuring the label maker as a wireless printer, Figure 8 disconnect the USB cable from your computer. 4 Place the printe
Resumen del contenido incluido en la página 12
6 Do one of the following: • If this is the first DYMO label printer installed on the computer, click Yes when prompted by the software to add the label maker as a wireless printer. • If a DYMO label printer is already installed on the computer, choose Add Network Printer from the File menu. 7 Follow the instructions in the Add Network Printer tool. ® To add the wireless printer to a Mac OS system 1 Download DYMO Label™ v.8.5 or later from the DYMO Web site at WirelessPnP.dymo.com. 2 Double-c
Resumen del contenido incluido en la página 13
For complete details on using the software, refer to the online Help or the DYMO Label User Guide. From the Help menu in DYMO Label software, you can view the following: DYMO Label Help DYMO Label User Guide LabelManager Wireless PnP User Guide 11
Resumen del contenido incluido en la página 14
Safety Precautions for Lithium-Ion Polymer Rechargeable Battery Pack Inaccurate handling of a lithium-ion polymer rechargeable battery pack may cause leakage, heat, smoke, an explosion, or fire. This could cause deterioration of performance or failure. This may also damage the protection device installed in the battery pack. This could damage equipment or injure users. Thoroughly follow the instructions below. While Charging the Battery Pack Danger When charging the battery pack, use dedic
Resumen del contenido incluido en la página 15
1-Year Warranty for Your DYMO Product Your electronic DYMO product is sold with a 1-year warranty from the date of purchase against defects in material and workmanship. DYMO will repair or replace your product free of charge on the following conditions: 1 Products returned under this warranty must be accompanied by a description of the defect together with a copy of the product’s proof of purchase and your full contact and delivery details: name, telephone, complete address – street, house
Resumen del contenido incluido en la página 16
PRODUCT OF / PRODUIT DE: NEWELL RUBBERMAID EUROPE SÀRL CHEMIN DE BLANDONNET 10 1214 VERNIER – SWITZERLAND DISTRIBUTED BY/DISTRIBUÉ PAR/DISTRIBUIDO POR: REPRESENTED IN THE EU BY / REPRÉSENTÉ EN UE PAR: PRODUCT OF / PRODUIT DE: DYMO, ATLANTA, GA 30328, L.P. WWW.DYMO.COM NWL BELGIUM SERVICES BVBA NEWELL RUBBERMAID EUROPE SÀRL IMPORTED INTO CANADA BY/IMPORTÉ AU CANADA INDUSTRIEPARK-NOORD 30 CHEMIN DE BLANDONNET 10 PAR SANFORD CANADA L.P., OAKVILLE, ON L6J 3J3 EN MÉXICO IMPORTADO Y DISTRIBUIDO POR
