Manual de instrucciones de Whirlpool W10096749

Resumen del contenido incluido en la página 1

WASHER INSTALLATION INSTRUCTIONS
Table of Contents
WASHER SAFETY............................................ 1
INSTALLATION REQUIREMENTS ................. 2
Tools and Parts ............................................. 2
Location Requirements................................. 2
Drain System................................................. 3
Electrical Requirements ................................ 3
INSTALLATION INSTRUCTIONS ................... 4
Before You Start...................................

Resumen del contenido incluido en la página 2

INSTALLATION REQUIREMENTS Alternate Parts Your installation may require additional parts. For information on Tools and Parts ordering, please refer to the toll-free phone numbers on the front Gather the required tools and parts before starting installation. page of the Washer User Instructions. The parts supplied are in the washer basket. If You Have: You Will Need to Buy: Tools needed for connecting the drain hose and water inlet hoses: Laundry tub or Sump pump system (if not already

Resumen del contenido incluido en la página 3

Laundry tub drain system (view C) Recessed area or closet installation The laundry tub needs a minimum 76 L (20 gal.) capacity. The top of the laundry tub must be at least 99 cm (39") above the floor and The dimensions shown are for the recommended spacing allowed no higher than 244 cm (96") from the bottom of the washer. (A and B), except the closet door ventilation openings. The dimensions shown for the closet door ventilation openings (C) are Floor drain system (view D) the minimum requi

Resumen del contenido incluido en la página 4

Do not earth to a gas pipe. Straight power cord
Check with a qualified electrician if you are not sure the washer is properly earthed.
Do not have a fuse in the neutral or earth circuit. EARTHING INSTRUCTIONS For an earthed, cord-connected washer: This washer must be earthed. In the event of a malfunction or breakdown, earthing will reduce the risk of electrical shock by providing a path of least resistance for electric current. This washer is equipped with a cord having an equipmen

Resumen del contenido incluido en la página 5

Looped power cord Remove drain hose from washer cabinet Gently pull the corrugated drain hose out of the washer from the top of the hose. Continue to pull the hose until the end emerges. Do not force excess drain hose back into the rear of the washer. Looped power cord Laundry tub drain or standpipe drain 1. Firmly grasp the yellow shipping strap and pull until both ends are completely removed from washer. Connecting the drain hose form to the corrugated drain hose A 2. Check that two (2)

Resumen del contenido incluido en la página 6

ConnecttheInletHoses The washer must be connected to the water faucets using the new inlet hoses. Do not use old hoses. Connect the inlet hoses to the washer Insert new flat washers (supplied) into each end of the inlet hoses. Firmly seat the washers in the couplings. A B AB A. Coupling B. Washer Connect the inlet hoses to the water faucets A. Cold water inlet valve Make sure the washer basket is empty. B. Hot water inlet valve 1. Attach the hose labeled hot to the hot water faucet. Screw

Resumen del contenido incluido en la página 7

2. Screw the locknut onto each foot to within 2.5 cm (1") of the foot base. Secure the Drain Hose 1. Remove the shipping strap from the power cord. Drape the power cord over the console. 2. Remove any cardboard used to move washer. 2.5 cm (1") 3. Screw the feet into the threaded holes at the front corner of the washer until the nuts touch the washer. Twist the feet to install. Beaded tie strap NOTE: Do not tighten the nuts until the washer is level. 3. Wrap the drain hose to the laundry tu

Resumen del contenido incluido en la página 8

4. If the washer is not level, move the washer out slightly, tip back, prop up the front of the washer with the wood block and Complete Installation adjust the feet up or down as necessary by twisting the feet. 1. Check the electrical requirements. Be sure that you have the Turn the feet clockwise to raise the washer or correct electrical supply and the recommended earthing counterclockwise to lower the washer. Repeat steps method. See “Electrical Requirements.” 1 through 4 until washer i