Resumen del contenido incluido en la página 1
INSTALLATION INSTRUCTIONS FOR PART 99-7951
APPLICATIONS
See application list inside
Chevrolet/Suzuki/Pontiac multi-kit
2004 - 2008
95-7951
KIT FEATURES
• Double DIN radio provision
• Stacked ISO units provision
KIT COMPONENTS
• A) Double DIN Trim Plate • B) Double DIN Brackets
A B
WIRING & ANTENNA CONNECTIONS (Sold Separately)
Wiring Harness:
• 70-2105 GM harness 2006-up
• 70-8405 GM/Suzuki/Daewoo harness 1999-up
Antenna Adapter:
• 40-CR10 Chryler antenna adapter 2002-up
TOOLS REQUIRED
Pane
Resumen del contenido incluido en la página 2
95-7951 Applications Chevrolet Suzuki Pontiac Aveo 2004-2006 Forenza 2004-2008 G3 Hatchback 2007 Aveo Hatchback 2007-2008 Reno 2005-2008 Verona 2004-2006 Table of Contents Dash Disassembly – Chevrolet Aveo 2004-2006 3 – Chevrolet Aveo Hatchback 2007-2008 3 – Pontiac G3 Hatchback 2007 3 – Suzuki Forenza 2004-2008 4-5 – Suzuki Reno 2005-2008 4-5 – Suzuki Verona 2004-2006 6 Kit Assembly – Double DIN radio provision 7-8 – Stacked ISO mount units provision
Resumen del contenido incluido en la página 3
Dash Disassembly 95-7951 Chevrolet Aveo 2004-2006 Chevrolet Aveo Hatchback 2007-2008 Pontiac G3 Hatchback 2007 1. Unclip and remove the trim panels from both sides of radio/climate controls. (Figure A) 2. Remove (4) Phillips screws securing the radio. Unplug and remove radio. (Figure B) Continue to kit assembly (Figure A) (Figure B) 3
Resumen del contenido incluido en la página 4
Dash Disassembly 95-7951 Suzuki Forenza 2004-2008 Suzuki Reno 2005-2008 1. Disconnect air selector cable on driver’s side of center console behind dash above accelerator pedal. (Figure A & B) 2. Open glove box and remove (5) Phillips screws ((3) on top and (2) on bottom) then remove entire glove box. 3. Disconnect temperature selector cable on passenger side of center console behind glove box. (Figure C) Continued on next page (Figure A) (Figure B) Inside of Glove Box (Figure C) 4
Resumen del contenido incluido en la página 5
Dash Disassembly 95-7951 Suzuki Forenza 2004-2008 Suzuki Reno 2005-2008 4. Unsnap and remove entire panel surrounding radio. NOTE: The clips holding radio panel to dash are very strong. (Figure D) 5. Remove (4) 10 mm bolts securing radio. Unplug and remove radio. (Figure E) BASS MUTE Continue to kit assembly EQ AM/FM TAPE 1 2 3 AST TUNE CD 5 6 SCAN 4 (Figure D) (Figure E) 5
Resumen del contenido incluido en la página 6
Dash Disassembly 95-7951 Suzuki Verona 2004-2006 1. Unclip and remove the trim panel surrounding the radio. (Figure A) 2. Remove (4) Phillips screws from radio. Unplug and remove radio. (Figure B) Continue to kit assembly (Figure A) (Figure B) 6
Resumen del contenido incluido en la página 7
Kit Assembly 95-7951 Double DIN radio provision NOTE: For the Chevrolet Aveo 2004-06, Chevrolet Aveo Hatchback 2007- 08, Pontiac G3 Hatchback 2007 and Suzuki Verona 2004-06, cut and remove front lower mounting tabs from the Double DIN trim plate (Figure A). For the Suzuki Forenza 2004-08 and the Suzuki Reno 2005-08, cut the rear lower mounting tabs (Figure B). (Figure B) NOTE: The Verona 2004-2006 sub dash will need to be trimmed slightly for proper fit. Refer to illustration. (Figure
Resumen del contenido incluido en la página 8
Kit Assembly 95-7951 Double DIN radio provision 1. Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the unit for proper operation. 2. Snap the Double DIN brackets to the outside edge of the Double DIN trim plate. (Figure E) 3. Slide the Double DIN radio into the bracket/trim plate assembly and secure (Figure E) the radio to the assembly using the screws supplied
Resumen del contenido incluido en la página 9
Kit Assembly 95-7951 Stacked ISO mount units provision NOTE: For the Chevrolet Aveo 2004-06, Chevrolet Aveo Hatchback 2007- 08, Pontiac G3 Hatchback 2007 and Suzuki Verona 2004-06, cut and remove front lower mounting tabs from the Double DIN trim plate (Figure A). For the Suzuki Forenza 2004-08 and the Suzuki Reno 2005-08, cut the rear lower mounting tabs (Figure B). (Figure B) NOTE: The Verona 2004-2006 sub dash will need to be trimmed slightly for proper fit. Refer to illustration.
Resumen del contenido incluido en la página 10
Kit Assembly 95-7951 Stacked ISO mount units provision 1. Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the unit for proper operation. 2. Snap the Double DIN brackets to the outside edge of the Double DIN trim plate. (Figure E) 3. Slide the stacked ISO units into the bracket/trim plate assembly and secure (Figure E) the units to the assembly using the screws
Resumen del contenido incluido en la página 11
Notes
Resumen del contenido incluido en la página 12
INSTALLATION INSTRUCTIONS FOR PART 99-7951 METRA. THE WORLD’S BEST KITS.™ metraonline.com 1-800-221-0932 © COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORATION REV. 5/25/11
