Manual de instrucciones de American Standard Enfield Bathtub 2742.222

Resumen del contenido incluido en la página 1

Installation Instructions
DuraBond™
Construction
Enfield Bathtub
HIGH GLOSS ACRYLIC
2742.020, 2742.222 FITTINGS NOT INCLUDED
THANK YOU...for selecting American Standard . . . the benchmark of fine quality for over 100 years. To ensure that
your installation proceeds smoothly--please read these instructions carefully before you begin. All you need to finish the
installation are your selected fittings. (Certain installations may require professional help.) Also be sure your installation
conforms t

Resumen del contenido incluido en la página 2

1. Identify desired location of the tub. Please note: the floor area supporting the tub and frame must be capable of supporting a load in excess of 2000 lbs. The supplies and drain must not interfere with the floor joists (see rough-in for dimensions). 2. Place the wood frame, finished side down, on a soft surface to prevent scratching (an old blanket or quilt may be suitable). #1 3. Remove the unfinished shipping supports from each corner by remov- ing the four (4) wood screws in each corner. (

Resumen del contenido incluido en la página 3

17. Attach the anti-tip bracket to the floor using the 1/4” - 20 socket #5 head bolts and hex key wrench (see photo #5). 18. Repeat for the remaining brackets. Note - all brackets must have the opening pointing in the same direction. 19. Slide the frame into position. The leveler should touch the inside of the bracket as shown in photo #6. Tighten the lock nut onto the bracket so that it is snug. #6 20. Place the tub into the frame making sure that it is centered in the frame. 21. Check to see i

Resumen del contenido incluido en la página 4

34. Attach a screw in the bottom hole threading the screw into the slot. 35. Repeat steps 32 thru 34 on the inside of the leg. 36. Repeat for remaining legs. 37. Install the faucet and drain per manufacture’s instructions. #10 38. Place the wood inserts or cast grilles into the opening in the center of the 6’ side of the frame.. 39. Secure the panels to the frame with the deadbolt locks (see photo # 10). 40. Apply painters tape to the frame 1/8" from the deck edge around the perimeter of the tub

Resumen del contenido incluido en la página 5

AMERICAN-STANDARD ENFIELD BATHTUB FURNITURE WARRANTY If inspection of this American-Standard plumbing product, within one year after its initial purchase, confirms that it is defective in materials or workmanship, American-Standard will repair or, at its option, exchange the product for a similar model. Variations in actual wood color and finishes which may result from natural characteristics of the wood, such as grain patterns, mineral streaks and the like, are not defects and are not covered b

Resumen del contenido incluido en la página 6

AMERICAN STANDARD LIMITED WARRANTY ACRYLIC PRODUCTS American-Standard warrants to the original consumer purchaser that it will, at its option, repair or replace any of its plumbing products found by it to be defective under normal use and maintenance within the following periods from date of purchase: Shell - three (3) years This limited warranty DOES NOT COVER the following: 1. Defects or damage arising from shipping, installation, alterations, accidents, abuse, misuse, lack of proper maintenan

Resumen del contenido incluido en la página 7

INSTALLATION INSTRUCTIONS BATH FILLER SUPPLIES MODEL 9117.012 To ensure this product is installed properly, please read these instructions carefully before you begin. DESCRIPTION Bath Filler Supplies, Model 9117.012, includes 6” deck mount supply adapters, riser tubes, couplings, shutoff valves, and all fittings and supports needed to install and connect the 9116 Series Bath Filler to the water supplies. Adjust centerline spacing of supports and water supply lines as needed to accommodate

Resumen del contenido incluido en la página 8

Step 5. Disassemble union assembly with 4” long threaded nipple. Assemble brass flange nuts and flat rubber gasket onto threads of 4 long union nipple. Protect surface finish of union coupling or cover wrench jaws to prevent marring of finish on coupling and assemble coupling to the top of the supply riser. BE SURE TO USE TEFLON TAPE OR TEFLON PIPE SEALANT AT THIS CONNECTION. Step 6. APPLY TEFLON TAPE OR TEFLON PIPE SEALANT to threads on union nipple. 4” long thread