Resumen del contenido incluido en la página 1
Owner's Manual
®
Liquid Propane Gas Grill
Model 141.15337
Natural Gas Grill
Model 141.17337
WARNING: Note to Installer: Leave this Owner's Manual
with the consumer after delivery and/or installa-
Read this Owner's Manual carefully and be sure
tion.
your gas grill is properly assembled, installed and
maintained. Failure to follow these instructions
Note to Consumer: Leave this Owner's
could result in sedous bodily injuryand/or property
Manual in a convenient place for future reference.
damage. Th
Resumen del contenido incluido en la página 2
/_kWARNING Warranty ..................................................... 2 Combustion byproducts produced when using Safety Instructions .................................... 2 this product contain chemicals known to the State of California to cause cancer, birth Hardware ..................................................... 6 defects, or other reproductive harm. Parts Diagram and Lists ..................... 10 /_kWARNING Assembly Instructions .............................. 13 Failure to comply
Resumen del contenido incluido en la página 3
CorrectLP Gas Tank Use • LP gas tanks must be stored outdoors in a LP gasgdllmodelsaredesigned for usewitha well-ventilated area and out of the reach of standard 20 lb. LiquidPropane Gas(LPgas)tank, children. Disconnected LP gas tanks must not not included in gdllbox.Neverconnectyourgas be stored in a building, garage or any other gdllto an LPgastankthatexceedsthiscapacity. A enclosed area. tankof approximately 12inchesin diameter by 18-1/2incheshighis the maximum sizeLPgas • When your gas gdll
Resumen del contenido incluido en la página 4
Figure 1 (Natural gas model only) IMPORTANT: your Kenmore Natural Gas Grill can- GAS SUPPLY not be converted to use LP Gas. Attempting to do _'_ INSIDE so is extremely hazardous and wilt also void the grill _'_ WALL warranty. OUTSIDE WALL Your natural gas grill is designed to operate on TO GRILL natural gas only, at a pressure of 7" water column (W.C.) (1/4 psi or 1.75 kpa), regulated at the SHUT OFF LOCKING residential meter. Check with your gas utility SHUT OFF company for local gas pressure a
Resumen del contenido incluido en la página 5
CAUTION:Spidersand smallinsectsocca- To reducethe chanceof "FLASHBACK" (see sionallyspin websor makenestsin the grill CAUTION at right)cleanthe BurnerTubesand BurnerTubesduringtransitandwarehousing. Burnersbeforefully assembling yourgdll. Re- movethe CotterPinfrom the rearunderside of Thesewebscan leadto a gasflowobstruc- tion whichcouldresultin a fire in and eachBurnerusinga pair of long nosepliers. aroundthe BurnerTubes.This typeof fire is Carefullylift eachBurnerup and awayfrom the knownas a
Resumen del contenido incluido en la página 6
The following table illustrates a breakdown of the hardware pack. It highlights what components are used in the various stages of assembly. Ref. Component Qty. Purpose of Components 3/8"x85mm Wheel Bolt 2 H001 Install Wheels To Cart Legs H002 Spring Washer 2 H039 3/8" Nut 2 H019 1/4"x2" Pattern Head Screw 8 Attaches Cart Legs To Bottom Shelf H017 1/4"xl/2" Pattern Head Screw 4 Attaches Tank Pull-out Tray Kit To Bottom Shelf H017 1/4"xl/2" Pattern Head Screw 4 Attaches Rear Panel To Cart H019 1/4
Resumen del contenido incluido en la página 7
LPG GAS MODEL ONLY Actual Size and Quantity of Each Hardware Piece: 3/8"x85mm Wheel Bolt 3/8" Spring Washer 3/8" Nut Qty. 2 Qty. 2 Qty. 2 Ref. # H001 Ref. # H002 Ref. # H039 1/4"x3/4" Pattern Head Screw 1/4"x2" Pattern Head Screw 1/4"xl/2" Pattern Head Screw Qty. 12 Qty. 8 Qty. 18 Ref. # H018 Ref. # H019 Ref. # H017 AA Battery 1/4"x5/8" Partly-Threaded Bolt Magnetic Door Stop Qty. 4 Qty. 2 Qty. 2 Ref. # H006 Ref. # P05301001A Ref. # P05318022B Scale 1:2 Scale 1:2 J No.17 Customized Wrench Cotter
Resumen del contenido incluido en la página 8
The following table illustrates a breakdown of the hardware pack. It highlights what components are used in the various stages of assembly. Ref. Component Qty. Purpose of Components 3/8"x85mm Wheel Bolt 2 H001 Install Wheels To Cart Legs H002 Spring Washer 2 H039 3/8" Nut 2 H019 1/4"x2" Pattern Head Screw 8 Attaches Cart Legs To Bottom Shelf H017 1/4"xl/2" Pattern Head Screw 4 Attaches Rear Panel To Cart H019 1/4"x2" Pattern Head Screw 4 Attaches Door Bracket To Cart H017 1/4"xl/2" Pattern Head
Resumen del contenido incluido en la página 9
NG GAS MODEL ONLY Actual Size and Quantity of Each Hardware Piece: 3/8"x85mm Wheel Bolt 3/8" Spring Washer 3/8" Nut Qty. 2 Qty. 2 Qty. 2 Ref. # H001 Ref. # H002 Ref. # H039 1/4"x3/4" Pattern Head Screw 1/4"x2" Pattern Head Screw 1/4"xl/2" Pattern Head Screw Qty. 12 Qty. 8 Qty. 16 Ref, # H019 Ref. # H018 Ref, # H017 AA Bakery 1/4"x5/8" Partly-Threaded Bolt Magnetic Door Stop Qty. 4 Qty. 2 Qty. 2 Ref, # H006 Ref. # P05301001A Ref. # P05318022B Scale 1:2 Scale 1:2 J No,17 Customized Wrench Cotter P
Resumen del contenido incluido en la página 10
LPG = Liquid Propane Gas 4 1 NG = Natural Gas _/ 61 6O 41 37 20 19 fl 7 12 IQ \36 39_ 30(LPG only) 23_(NG only). 31(NG only) 22 6b-_ (NO only)6 (LPG only)4_ 18 3b lb / 1o / b(NG only) 40 47 Io(LPGonly) 45 68b(NG only) _Sb(LPG only) \53 b4 _71 only) _71(NG only) lO
Resumen del contenido incluido en la página 11
REF# DESCRIPTION PART# QTY 1. Stainless Steel Lid PO0117336A 1 2. Lid Side Panel - Left PO0105227P 1 1 3. Lid Side Panel - Right PO0106227P PO0607153A 1 4. Temperature Gauge 5. Lid Handle 1 PO0205030B 6. Heat-Insulating Spacer PO6801002A 2 7. Name Plate P00410037C 1 PO1508026E 1 8. Secondary Cooking Rack - Porcelain 9. Cooking Grid - Porcelain PO1615027E 3 10. Flame Tamer - Porcelain PO1705016E 3 P02001006C 6 11. Main Burner w, Heat-Insulating Ring 11a. Air Shutter for Main Burner (NG only) P055
Resumen del contenido incluido en la página 12
REF# DESCRIPTION PART# QTY 1 44. Cart Leg - Caster Side P00901001C 1 45. Cart Leg - Wheel Side P00902030C 46. Rear Panel P07702009B 1 47. Door Bracket P03301016D 1 48a. Door ,Left P04302010A 1 1 48b. Door ,Right (LPG only) P04301010A 1 48c. Door ,Right (NG only) P04303014A 49. Door Handle P00215019H 2 50. Magnetic Door Stop P05318022B 2 1 51. Tank Pull-out Tray Kit- Black (LPG only) Y0340008 1 52. Fuel Gauge Display Kit (LPG only) P05310030B 53. Wheel - Black P05102017A 2 2 54. Weel Hub Cap - Bl
Resumen del contenido incluido en la página 13
Figure 1 CARTLEG CAUTION: Whileit ispossible foroneperson to CARTLEG-LEFT BRACKET_ assemble this grill, obtain assistance from another person when handling some of the larger, heavier pieces, especially the grill head. 1. Open Lid of shipping carton and remove top sheet of cardboard. Lay cardboard sheet on floor and use as a work surface to protect floor and grill parts from scratches. CART LEG 2. Slice all carton corners with a sharp utility knife to -RIGHT lay open the carton panels. 3. Remove
Resumen del contenido incluido en la página 14
7. Install the Door Bracket to the inside of front Figure 4a (LP gas model only) Cart Legs. Align the threaded holes on the Door Bracket with the holes on Cart Legs. Tighten securely by using 4 of the 1/4"x2" Pattern Head Screws provided. (See Fig. 3. on page 11) Upper door bolt holes (at ends of bracket) must face outward. BRACKET Installing The Cabinet Doors Found in For LPG Gas grills: Hardware Pack 1. Install the Door Stops to the Bottom Shelf and the Door Bracket. See Fig. 4a. SHELF 2. Alig
Resumen del contenido incluido en la página 15
Figure 5a (NG gas model only) Installing The Cabinet Doors For NG Gas grills: 1. Install the Door Stops to the Bottom Shelf and the Door Bracket. See Fig. 5a. 2. Align the holes on the Door Stops with the threaded holes on the top of the Bottom Shelf BRACKET and bottom side of Door Bracket. Tighten securely by using 4 of the 1/4"xl/2" Pattern Head Screws provided. See Fig.5a. Foundin Hardware Pack 3. Remove the white protective film from the stainless steel Doors. Attach a Door Handle to each Fr
Resumen del contenido incluido en la página 16
Installing The Grill Head Figure 6a (LP gas model only) GRILL BOWL SiDE 1. Now that you've assembled the grill cart you PANEL HEAD can install the pre-assembled Grill Head. See tGN_TION WIRE FROM GRILL HEAD Fig. 6a or 6b. If you haven't already done so, we suggest you open the Grill Lid and remove the packed components. Even with the compo- nents removed, this next step requires 2 CART LEG people. BE CAREFUL NOT TO PINCH FINGERS \ WHEN LOWERING HEAD ONTO CART WIRE FASTENER 2. For LP Gas grills:
Resumen del contenido incluido en la página 17
Installing Side Shelf, Side Burner and Tool Figure 8a Holder Kit SIDE SHELF FRAME Remove Side Burner from Side Burner Kit before GRILL HEAD installing. 1. Enlisting the aid of an assistant, attach Side Burner Frame to right side of grill. Attach Side Shelf SIDE BURNER Frame to left side of grill as shown in Fig. 8a. FRAME Align the 4 holes on Side Shelf Frame and Side Burner Frame with the threaded holes on left and right Bowl Support Brackets. Tighten securely using 4 of the 1/4"x3/4" Pattern H
Resumen del contenido incluido en la página 18
6. For Natural Gas grills: Figure 8d (Natural gas model only) Connect the Ignition Wire terminal from Side Burner with the other from Grill Head. See Fig. 8d. Bind POT SUPPORT the connected Ignition Wires, and Connection Tube together using the supplied Fastening Band. 7. The gap between the Side Burner Electrode Tip SIDE and the Side Burner Port should be approximately 1/8"~3/16 ''. See Fig. 8e.lf the gap is wider than 3/16", use a pair of long nose pliers and gently bend the Electrode Tip towa
Resumen del contenido incluido en la página 19
Ignitor Battery Installation - See Fig. 9 Electrode Check - Requires an Assistant Before placing the cooking components into your 1. Unscrew both Ignitor Caps located on the grill Control Panel and remove the Contact and grill, ensure that the Spark Electrode Tip is properly positioned within each Gas Collector Box ( a Spring from each Ignitor Slot. 3-1/4" wide stainless mechanism found at the front between each set of Burners.) The easiest way to 2. Place the manufacturer supplied AA battery en
Resumen del contenido incluido en la página 20
Installing Cooking Components Figure 11 Important: Before cooking on your grill the first SECONDARY COOKING RACK time, wash the Cooking Grids and Cooking Rack with warm, soapy water. Rinse and dry thoroughly. Season with cooking oil regularly. After cooking is COOKING GRID completed, turn grill to HIGH setting three to five minutes to burn off excess grease or food residue. FLAME TAMER 1. Place the three Flame Tamers on the lower ledge above Burners. See Fig. 11. 2. Evenly space the Cooking Grid
