Resumen del contenido incluido en la página 1
1
Competitor
Ultra Light Plus, Semi Electric Bed
Item # 15560
Owner’s Assembly And Operating Manual
Resumen del contenido incluido en la página 2
2 Assembly Instructions 1. Remove contents from carton. 2. Place both ends of the sleep surface on their side and align the flange with the receptacle as shown. 3. T o attach the head and foot spring, pull the black knob away for the frame and slide the two sides together . The lock knob is spring loaded and will lock into position when released and the two sections of the bed are flush together . To disassemble the head and foot section, pull the black lock knob out and rotate the k
Resumen del contenido incluido en la página 3
3 Assembly Instructions Cont. 4. Secure the sleep surface with the cotter pin as shown. 5. Lock the cotter pin with the attached clasp. Repeat on the opposite side.
Resumen del contenido incluido en la página 4
4 Assembly Instructions Cont. HAND CONTROL The Competitor bed comes with a hand control that will illuminate when the bed is plugged into a grounded or polarized wall outlet, or with 9V battery (not included) installed in the hand control. The hand control will illuminate as long as the wall or battery has power . With this battery installed, the motor can be operated to return the sleep surface to the horizontal position in the event of a power failure. 6. NOTE: Before installing mot
Resumen del contenido incluido en la página 5
5 Assembly Instructions Cont. There are two methods for the installation of the motor Method A The motor is installed on the bed frame when the frame is standing on its side. Installation instructions can be found on pages 7-8. Method B The motor is installed from underneath the bed frame (horizontal to the ground) Installation instructions can be found on pages 10-11.
Resumen del contenido incluido en la página 6
6 Assembly Instructions Cont. Method A Installation of the motor when bed frame is on its side A1. Prior to installation, make sure that the 2 white motor blocks are in the retracted position. CORRECT INCORRECT Actuator Bar A2. Align the opening on the head end of the motor with the flange on the head section of the bed and insert the flange into the motor compartment. Flange A3. With the palm of your hand, snap the motor flush to the actuator bar . A4. Align the opening on the
Resumen del contenido incluido en la página 7
7 Assembly Instructions Cont. A6. Once in place, replace the motor covers to secure the motor. A6. Once the motor is attached, lay bed flat and install head and foot boards. There are 2 height adjustments on the head and foot board. Select the desired positions and hook the frame onto the foot board. Slide lock towards leg of foot board to secure position as shown. Repeat for opposite side. HEIGHT ADJUSTMENT 9. The Competitor bed deck has two height adjustments. 10. Adjustment one is loc
Resumen del contenido incluido en la página 8
8 Assembly Instructions Cont. The chart below indicates the height adjustments as they relate to the two adjustment options. Deck Height (inches) Deck Height Pins Leg Hole Wheels 1 1* Lower Low No 13.125 Upper Low No 14 Lower Low Y es 14.152 Lower Middle No 16.125 Upper Low Y es 16.25 Upper Middle No 17.152 Lower Middle Y es 17.875 Lower High No 19.25 Upper Middle Y es 20 Upper High No 20.875 Lower High Y es 23 Upper High Y es *Rails cannot b
Resumen del contenido incluido en la página 9
9 Assembly Instructions Cont. Method B Installation of the motor from underneath the frame B1. Attached head a foot board to frame. B2. Repeat for the other side. Deck Height Pins Upper Lower Leg Holes 1- High 1- Medium 1- Low End Method A
Resumen del contenido incluido en la página 10
10 Assembly Instructions Cont. B3. Prior to installation, make sure that the 2 white motor blocks are in the retracted position. CORRECT INCORRECT B4. Remove the covers from the motor and place under the bed and aligned with the actuator under the head section. There are labels on the motor that provide direction and placement in relation to the head section. B5. With both hands, lift the motor and insert into the actuator and frame as shown. With the palm of your hand snap the motor flu
Resumen del contenido incluido en la página 11
11 Assembly Instructions Cont. B6. Once in place, replace the motor covers to secure the motor. End Method B
Resumen del contenido incluido en la página 12
12 Assembly Instructions Cont. 12. Adjustment two is on the leg of the head and foot board. T o adjust, loosen the thumb screw on the leg and pull on the spring loaded knob with one hand and slide the leg to the desired height with the other hand. Once the desired position is found, turn the thumb screw until tight. Adjust other legs to the same position. REV3.1.23.14
Resumen del contenido incluido en la página 13
13 Assembly Instructions Cont. HEIGHT ADJUSTMENT 13. The Competitor bed deck has two height adjustments. 13A. Adjustment one is located on the frame as indicated below . There is a high position and a low position. The chart below indicates the height adjustments as they relate to the two adjustment options. Deck Height (inches) Deck Height Pins Leg Hole Wheels 1 1* Lower Low No 13.125 Upper Low No 14 Lower Low Y es 14.152 Lower Middle No 16.125 Upper Low Y es
Resumen del contenido incluido en la página 14
14 Assembly Instructions Cont. 14. The Competitor bed comes with a caster accessory (sold separately , model # 15044SET). T o install the casters, insert the stem of the caster into the leg receptacle as shown. It is recommended to install 1 non-locking caster on each bed end. The locking casters should be installed diagonally from each other . REV3.1.23.14
Resumen del contenido incluido en la página 15
15 Assembly Instructions Cont. 15. T o install bed rails, lift the head section and find the rail receptacle located on the frame of the bed as shown. 16. Pull receptacle outward and return head section to the flat position. 17. Turn the receptacle in order to receive the rail. Repeat for all four rail receptacles.
Resumen del contenido incluido en la página 16
16 Assembly Instructions Cont. 18. Insert the bed rail into the receptacle. Repeat for the other rail. NOTE: The competitor bed can be used with a free standing trapeze or a Drive Medical frame mounted trapeze (Item # 15560TRAPEZE). A trapeze cannot be mounted on the Competitor head board. REV3.1.23.14
Resumen del contenido incluido en la página 17
17 Maintenance & Safety Checks Drive recommends the following maintenance and cleaning procedures be conducted between users. ELECTRONICS • Check all controls to make sure all functions work properly . • Foot control • Head control • Check all cables for damaged or frayed wires. • Power cord • Pendant cord • Check to make sure all plugs are fully inserted or attached. • Check 9V battery on motor and hand control and replace annually . BED FRAME & SLEEPING SURFACE • V isually check al
Resumen del contenido incluido en la página 18
18 99 Seaview Boulevard Port Washington, NY 11050 Phone: 516-998-4600 Toll Free: 877.224.0946 Fax: 516.998.4601 www.drivemedical.com REV3.1.23.14
