Resumen del contenido incluido en la página 1
Angle Grinder
100 mm (4”) 115 mm (4-1/2”)
MODEL 9560CV MODEL 9564CV
100 mm (4”) 125 mm (5”)
MODEL 9563CV MODEL 9565CV
115 mm (4-1/2”)
MODEL 9561CV
DOUBLE
INSULATION
INSTR U CTION MANU AL
WARNING:
For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
www.makitatools.com
Resumen del contenido incluido en la página 2
SPECIFICATIONS Model 9560CV 9563CV 9561CV 9564CV 9565CV No load speed 2,800-10,500/ 2,800-10,500/ 2,800-10,500/ 2,800-10,500/ 2,800-10,500/ (RPM) min min min min min 289 mm 289 mm 299 mm 299 mm 299 mm Overall length (11-3/8”) (11-3/8”) (11-3/4”) (11-3/4”) (11-3/4”) Net weight 1.7 kg (3.7 lbs) 1.7 kg (3.7 lbs) 1.8 kg (4.0 lbs) 1.8 kg (4.0 lbs) 1.8 kg (4.0 lbs) Spindle thread M10 x 1.25 M10 x 1.25 5/8” 5/8” 5/8” • Manufacturer reserves the right to change specifications without notice. Specific
Resumen del contenido incluido en la página 3
5. Avoid body contact with grounded sur- be used for appropriate conditions. Ordinary faces such as pipes, radiators, ranges and eye or sun glasses are NOT eye protection. refrigerators. There is an increased risk of Tool Use and Care electric shock if your body is grounded. 15. Use clamps or other practical way to 6. Do not expose power tools to rain or wet secure and support the workpiece to a conditions. Water entering a power tool will stable platform. Holding the work by hand or increase th
Resumen del contenido incluido en la página 4
24. When servicing a tool, use only identical Use of unauthorized parts or failure to follow replacement parts. Follow instructions in Maintenance instructions may create a risk of the Maintenance section of this manual. electric shock or injury. USE PROPER EXTENSION CORD: Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in l
Resumen del contenido incluido en la página 5
8. Be careful not to damage the spindle, the poor installation or a poorly balanced flange (especially the installing surface) wheel. or the lock nut. Damage to these parts 15. Use the specified surface of the wheel to could result in wheel breakage. perform the grinding. 9. NEVER use tool with wood cutting blades 16. Watch out for flying sparks. Hold the tool or other sawblades. Such blades when so that sparks fly away from you and other used on a grinder frequently kick and persons or flammabl
Resumen del contenido incluido en la página 6
FUNCTIONAL CAUTION: DESCRIPTION • Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. 002978 Shaft lock 1 CAUTION: • Never actuate the shaft lock when the spindle is moving. The tool may be damaged. Press the shaft lock to prevent spindle rotation when install- ing or removing accessories. 1. Shaft lock 001035 Switch action 1 CAUTION: • Before plugging in the tool, always check to see that the slide switch actuates properly and returns t
Resumen del contenido incluido en la página 7
Number RPM (/min) CAUTION: 1 2,800 | | • If the tool is operated continuously at low speeds for a 2 4,000 | | long time, the motor will get overloaded and heated up. 3 6,500 | | • The speed adjusting dial can be turned only as far as 5 4 9,000 and back to 1. Do not force it past 5 or 1, or the speed | | 5 10,500 adjusting function may no longer work. The tools equipped with electronic function are easy to oper- ate because of the following features. • Electronic constant speed control Possible t
Resumen del contenido incluido en la página 8
002981 Loosen the lever on the wheel guard. Mount the wheel guard 1 with the protrusion on the wheel guard band aligned with the notch on the bearing box. Then rotate the wheel guard around 180 degrees. Tighten the lever to fasten the wheel guard. If the lever is too tight or too loosen to fasten the wheel guard, loosen or tighten the screw to adjust the tight- ening of the wheel guard band. To remove wheel guard, follow the installation procedure in 1. Screw reverse. 002982 Installing or removi
Resumen del contenido incluido en la página 9
001107 Installing or removing abrasive disc 1 (optional accessory) 2 NOTE: 3 • Use sander accessories specified in this manual. These must be purchased separately. Mount the rubber pad onto the spindle. Fit the disc on the rubber pad and screw the lock nut onto the spindle. To 1. Lock nut tighten the lock nut, press the shaft lock firmly so that the 2. Abrasive disc 3. Rubber pad spindle cannot revolve, then use the lock nut wrench and securely tighten clockwise. To remove the disc, follow the
Resumen del contenido incluido en la página 10
grinder in the B direction or it will cut into the workpiece. Once the edge of the wheel has been rounded off by use, the wheel may be worked in both A and B direction. 001136 Operation with wire cup brush (optional accessory) 1 CAUTION: • Check operation of brush by running tool with no load, insuring that no one is in front of or in line with brush. • Do not use brush that is damaged, or which is out of balance. Use of damaged brush could increase potential 1. Wire cup brush for injury from c
Resumen del contenido incluido en la página 11
001618 Operation with abrasive cut-off wheel 1 (optional accessory) 2 3 WARNING: 4 • When using an abrasive cut-off wheel, be sure to use only the special wheel guard designed for use with cut- off wheels. • NEVER use cut-off wheel for side grinding. 1. Lock nut 2. Abrasive cut-off wheel During cutting operations, never change the angle of the 3. Inner flange wheel. Placing side pressure on the cut-off wheel (as in 4. Wheel guard for cut-off wheel grinding) will cause the wheel to crack and bre
Resumen del contenido incluido en la página 12
guards as recommended in this manual. Your failure to do so could result in personal injury to you and others. If you need any assistance for more details regarding these accessories, ask your local Makita service center. 001180 1 222 8 12 13 3 3 9 11 3 4 6 10 14 5 7 5 5 9560CV/9563CV 9561CV/9564CV 9565CV 1 Grip 36 2 Wheel guard 3 Inner flange 35 Inner flange 45 4 Depressed center grinding wheel/Multi-disc 5 Lock nut 10-35 Lock nut 5/8-45 6 Plastic pad - N/A 7 Flex wheel - N/A 8 Rubber pad 76 Ru
Resumen del contenido incluido en la página 13
First-Class Postage Required Post Office will not deliver without proper postage. Makita U.S.A., Inc. 14930 Northam Street La Mirada, CA 90638-5753 Fold 13 Cut
Resumen del contenido incluido en la página 14
MAIL THIS PORTION Your answers to the following questions are appreciated. 1. This product was purchased from: 3. How did you learn about this product: Home Center Other ( ) Magazine Radio Hardware/Lumber Store From Dealer Exhibition Tool Distributor Newspaper From Friend Industrial Supply Store Display Previous Usage Construction Supply Catalog Other ( ) 2. Use of the product is intended for: 4. Most favored points are: Construction Trade Design Repair Se
Resumen del contenido incluido en la página 15
FACTORY SERVICE CENTERS 1-800-4-MAKITA RETAIN THIS PORTION FOR YOUR RECORDS ARIZONA FLORIDA MISSOURI PENNSYLVANIA 3707 E. Broadway Rd., Ste. 6 750 East Sample Road 9876 Watson Road 1704 Babcock Blvd. Phoenix, AZ 85040 Pompano Beach, FL 33064 St. Louis, MO 63126-2221 Pittsburgh, PA 15209 (602) 437-2850 (954) 781-6333 (314) 909-9889 (412) 822-7370 CALIFORNIA GEORGIA NEBRASKA PUERTO RICO 41850 Christy St. 4680 River Green Parkway NW 4129 S. 84th St. 200 Guayama St. Fremont, CA 94538-5107 Duluth,
Resumen del contenido incluido en la página 16
WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry products, and • arsenic and chromium from chemically-treated lumber. Your risk from these exposures varies, depending on how often you do this type of
