Resumen del contenido incluido en la página 1
Bench Grinder
37822, 37823,
39797, 39798,
Set up and OperatinG inStructiOnS
®
distributed exclusively by harbor Freight t ools .
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
read this material before using this product.
Failure to do so can result in serious injury.
SaVe thiS manual.
© ®
Copyright 1998 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape
Resumen del contenido incluido en la página 2
inStructiOnS FOr puttinG cOntentS int O uSe .................................... 9 impOrtant SaFetY aSSemBl Y.........................................9 inFOrmatiOn ............................ 3 OperatinG inStructiOnS .... 11 General tOOl SaFetY WarninGS ......................................3 WOrk piece and WOrk area Set up .......................................... 11 GrOundinG inStructiOnS ..... 5 General OperatinG inStructiOnS ............................ 11 110-120 V~ GrOunded tOOlS:
Resumen del contenido incluido en la página 3
nOtice is used to SaVe thiS manual address practices Keep this manual for the safety warn- not related to personal injury. ings and precautions, assembly, operat- cautiOn, without ing, inspection, maintenance and cleaning the safety alert procedures. Write the product’s serial symbol, is used to address number in the back of the manual near the practices not related to assembly diagram (or month and year of personal injury. purchase if product has no number). Keep this manual and
Resumen del contenido incluido en la página 4
7. DON’T FORCE TOOL. It will do the glasses only have impact resistant job better and safer at the rate for lenses, they are NOT safety glasses. which it was designed. 12. DON’T OVERREACH. Keep proper 8. USE RIGHT TOOL. Don’t force tool footing and balance at all times. or attachment to do a job for which it 13. MAINTAIN TOOLS WITH CARE. was not designed. Keep tools sharp and clean for best recOmmended minimum Wire and safest performance. Follow GauGe FOr eXtenSiOn cOrdS instructions for
Resumen del contenido incluido en la página 5
direction of rotation of the blade or equipment-grounding conductor to a cutter only. live terminal. 20. NEVER LEAVE TOOL RUNNING 4. Check with a qualified electrician or UNATTENDED. TURN POWER OFF. service personnel if the grounding instructions are not completely under- stood, or if in doubt as to whether the GrOundinG inStructiOnS tool is properly grounded. tO preVent 5. Use only 3-wire extension cords that electric ShOck have 3-prong grounding plugs and and death FrOm 3-pole recept
Resumen del contenido incluido en la página 6
adequate protection. Eye protection Grinder Safety Warnings must be ANSI-approved and breath- For Your Own Safety read instruction ing protection must be NIOSH-ap- manual Before Operating Grinder proved for the specific hazards in the work area. 1. Wear eye protection. 15. Industrial applications must follow 2. Use grinding wheel suitable for speed OSHA guidelines. of grinder. 16. Maintain labels and nameplates on 3. Replace cracked wheel immediately. the tool. These carry important safe
Resumen del contenido incluido en la página 7
particles. (California Health & Safety white or blue fingers), seek medical Code § 25249.5, et seq.) advice as soon as possible. 20. WARNING: Handling the cord on 2. Do not smoke during use. Nico- this product will expose you to lead, tine reduces the blood supply to the a chemical known to the State of hands and fingers, increasing the risk California to cause cancer, and birth of vibration-related injury. defects or other reproductive harm. 3. Wear suitable gloves to reduce the Wash han
Resumen del contenido incluido en la página 8
SpeciFicatiOnS unpackinG When unpacking, make sure that the all models item is intact and undamaged. If any parts 180264 are missing or broken, please call Harbor Motor No Load Speed 3450 RPM Freight Tools at 1-800-444-3353 as soon Arbor Size 5/8” with 1/2” Adapter as possible. Base Size 5” x 7” Mounting Holes 2 x 3/8” Work Light Bulb 40 W Household type mOdel 37822 Electrical Input 120 V~ / 60 Hz / 1/2 HP Wheel Size 6” x 3/4” x 1/2” Work Light Bulb 40 W Household type mOdel 37823 Electrica
Resumen del contenido incluido en la página 9
shown in Figure 1. Use bolts and inStructiOnS FOr washers to secure them in place as puttinG int O uSe shown in Figure 1. read the entire impOrtant note: There is a left and a right tool rest. SaFetY inFOrmatiOn Refer to Figure 1 to be certain that section at the beginning of this you install them correctly. manual including all text under c. The tool rests should be adjusted to subheadings therein before set within 1/16” of the grinding wheel. up or use of this product. To adjus
Resumen del contenido incluido en la página 10
3. installing Bracket to eye Shield - FiGure 3 a. Select one flat bracket and one eye shield. Assemble as shown in Fig- ure 3. b. Repeat for left eye shield. 4. installing eye Shield to Grinder - a. For installation of the right eye shield (19), make sure that the holes in the eye shield bracket face downward. FiGure 4 b. Push eye shield bracket onto mount- ing bracket until it locks into place as shown in Figure 4. c. Repeat for left eye shield. Bench Grinder For technical questions, pleas
Resumen del contenido incluido en la página 11
outward from the edge of the shank OperatinG inStructiOnS of the screwdriver. They should be read the entire impOrtant flat with intersecting faces perpen- SaFetY inFOrmatiOn dicular. Hold each face of the screw- section at the beginning of this driver against the wheel to true it up, manual including all text under then ease the end straight into the subheadings therein before set stone to grind it true. up or use of this product. 3. Sharpening knives - Remove metal from both faces of
Resumen del contenido incluido en la página 12
grooved, rounded, chipped, out of maintenance and true or loaded with foreign material. Ser VicinG Cracked wheels should be replaced immediately. Procedures not specifically explained in this manual 4. Wheel replacement - must be performed only by a If you must replace a wheel be sure qualified technician. to obtain one with a safe rated speed at least as high as the rated RPM of tO preVent this grinder. Be sure tool is switched SeriOuS injur Y off and unplugged before attempt
Resumen del contenido incluido en la página 13
t roubleshooting problem possible causes likely Solutions Tool will not start. 1. Cord not connected. 1. Check that cord is plugged in. 2. No power at outlet. 2. Check power at outlet. If outlet is unpowered, turn off tool and check circuit breaker. If breaker is tripped, make sure circuit is right capacity for tool and circuit has no other loads. 3. Tool’s thermal reset breaker 3. Turn off tool and allow to cool. Press tripped (if equipped). reset button on tool. 4. Internal damage
Resumen del contenido incluido en la página 14
pleaSe read the FOllOWinG careFull Y THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS qUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS qUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/ OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACE
Resumen del contenido incluido en la página 15
aSSemBl Y diaGram record product’s Serial number here: note: If product has no serial number, record month and year of purchase instead. note: Some parts are listed and shown for illustration purposes only, and are not avail- able individually as replacement parts. reV 01k Bench Grinder For technical questions, please call 1-800-444-3353. Page 15 4b 4b 4a 4a 38 39 40
Resumen del contenido incluido en la página 16
limited 1 Year / 90 da Y WarrantY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that for a period of ninety days from date of purchase that the engine/motor, the belts (if so equipped), and the blades (if so equipped) are free of defects in materials and workmanship. Har- bor Freight Tools also warrants to the original purchaser, for a period of one year from date of purchase, that al
