Resumen del contenido incluido en la página 1
HR-2410GH
Cold Water
Pressure Washer
Operator's Manual
Resumen del contenido incluido en la página 2
table of Contents intRoduCtion ............................................................................................................................. 3 imPoRtant safety W aRninGs .............................................................................................4-7 FIRE & VENTILATION PRECAUTIONS ...................................................................................4 SPRAY PRECAUTIONS ...................................................................................
Resumen del contenido incluido en la página 3
intRoduCtion Congratulations on the purchase of your John Deere pressure washer! You can be assured your John Deere pressure washer was constructed with the highest level of precision and accuracy. Each component has been rigorously tested by technicians to ensure the quality, endurance and performance of this unit. This operator's manual was compiled for your benefit. By reading and following the simple safety, installation, operation, maintenance and troubleshooting steps described in
Resumen del contenido incluido en la página 4
imPoRtant safety WaRninGs fiRe & Ventilation PReCautions: . This unit was designed for outdoor use only. NEVER operate this unit in an enclosed area. ALWAYS make certain there is adequate air (oxygen) for combustion as well as ventilation to prevent the presence of poisonous carbon monoxide gases. Beware of poorly ventilated areas or exhaust fans which can cause inadequate combustion or engine overheating. 2. NEVER operate this unit in the presence of flammable vapors or combustible d
Resumen del contenido incluido en la página 5
imPoRtant safety WaRninGs sPRay PReCautions: danGeR RIsk Of INjECTION OR sEvERE CUTTING INjUR y KeeP CleaR of nozzle do not diReCt disCHaRGe stReam at PeRsons oR Pets. only tRained oPeRatoRs sHould use tHis PRoduCt. basiC PReCautions sHould al Ways be obseRVed, inCludinG tHe folloWinG: . KEEP AWAY FROM THE SPRAY: a. Because of the high pressure and velocity of the spray, fluids can penetrate the skin, causing serious injury. b. Never point the gun at yourself or anyone else. Never put your
Resumen del contenido incluido en la página 6
imPoRtant safety W aRninGs deteRGent CleaninG PReCautions: . DO NOT use solvents or highly corrosive detergents or acid type cleaners with this pressure washer. Use only mild detergents. 2. KNOW YOUR DETERGENTS! Be prepared to tell a physician exactly what you are using in the event of an emergency. Read the Material Safety Data Sheet (MSDS) provided with your detergent and all detergent labels. Follow all appropriate instructions regarding preparation, use, safety and transportation.
Resumen del contenido incluido en la página 7
imPoRtant safety W aRninGs adJustment PReCautions: . NEVER alter or modify the equipment, be sure any accessory items and system components being used will withstand the pressure developed. Use ONLY genuine manufacturer parts for repair of your pressure washer. Failure to do so can cause hazardous operating conditions and will void warranty. . NEVER make adjustments to the machinery while it is connected to the engine without first removing the ignition cable from spark plug. Turning
Resumen del contenido incluido en la página 8
featuRes foR HR-2410GH featuRes listinG . Decal: Warning/Caution/Operation (E) . Detergent Strainer . Nozzle Assembly 3. High Pressure Hose 3. Decal: Risk of Injection 4. Detergent Hose 4. Lance 5. Thermal Relief Valve 5. Gun/Wand Assembly 6. Pump-Axial Piston 6. Decal: Caution Risk of Fire 7. Water Supply-Inlet 7. Engine 8. Inlet Filter 8. Decal: Caution Allow to Cool 9. High Pressure Outlet 9. Engine Run Switch 0. Chemical Injection Inlet 0. Engine Oil Fill .
Resumen del contenido incluido en la página 9
safety deCals & PlaCement foR HR-2410GH DO NOT REmOvE sAfET y DECAls fROm UNIT UNlEss REplACING WITh mOsT CURRENT sAET f y DECAl!!! Reference # Decal: Caution-Allow to Cool (Part #34-0599) CAUTION/PRECAUCION RISK OF FIRE RIESGO DE FUEGE No ponga combustible cuando Do not add fuel when el producto este en operacion. product is operating. Allow Permita que el motor se enfrie engine to cool for two () por minutos antes de minutes before refueling. reablastecer de combustible. 3
Resumen del contenido incluido en la página 10
installation & PReP aRation attiRe: Proper attire is essential to your safety. It is advised to utilize whatever means necessary to protect eyes, ears, and skin. Additional safety attire (such as respiratory mask) may be required when using detergent cleaning agents with this washer. set -uP: DANGER . This unit should only be placed on a level surface to ensure proper lubrication RisK of eXPlosion oR fiRe! for the engine and water pump while operating. do not Pla Ce unit in an . DO NOT
Resumen del contenido incluido en la página 11
installation & PReP aRation WARNING nozzle ReVieW : Ris K of in Je Ction Causin G Your pressure washer is equipped with an adjustable nozzle which has two seVeRe inJuR y! functions. Review the nozzle assembly instructions listed below. -neVeR looK diReCtly at tHe nozzle o Rifi Ce unless it NOTE: The nozzle assembly should NOT be connected to the gun assembly is dis Conne Cted f Rom t He at this time. Gun/W and assembly! . Selections of high and low pressure can be achieved by pulling
Resumen del contenido incluido en la página 12
installation & PReP aRation CHeCK WateR inlet stRaineR WateR suPPly: . Select a water supply hose which is a quality grade of garden hose measuring at least 3/4" ID and no longer than 50 feet. 2. Check the water inlet filter to ensure it is clean and free of any obstructions. Periodic cleaning of the water filter will help prevent pump problems. As a filter becomes obstructed, it restricts proper flow of water to the pump. This can result in cavitations which will cause premature failure
Resumen del contenido incluido en la página 13
installation & PReP aRation PRe-staRt insPeCtion PRoCeduRes: Before starting the unit, perform the following procedures: . Check the oil level in the pump and engine. 2. Inspect the water inlet filter. Clean or replace if necessary. See "Water Supply", #, pg. . 3. Check all hose connections to ensure they are securely tightened. See "Water Supply", #3, pg. . 4. Inspect for system fuel leaks. If a fuel leak is found, DO NOT START UNIT! See "Fire & Ventilation Precautions", #2 and #4
Resumen del contenido incluido en la página 14
oPeRatinG instRuCtions nozzle ConneCtion PRiminG tHe PumP: . It is essential to prime the pump on initial start-up and each time the water supply is disconnected from the unit after initial use. 2. Lay the high pressure hose out to remove any loops. Water flow will tighten the hose, creating tight loops if the hose is not straight. DISCONNECT NOTE: The nozzle assembly should NOT be connected to the gun assembly at this time. See "Nozzle Connection", pg. 11 3. With the trigger gun loc
Resumen del contenido incluido en la página 15
oPeRatinG instRuCtions CleaninG WitH deteRGents: 1. Refer to "Detergent Cleaning Precautions" pg. 6. Be certain to wear protective safety attire as stated on pg. 0. . Prepare detergent solution according to label directions. Never pump acids, akalines abrasive fluids or solvents thru the unit. 3. Connect the detergent hose to the unit as shown on page 8. The detergent ratio is preset and cannot be adjusted. 4. Immerse the detergent strainer into the detergent solution to allow detergen
Resumen del contenido incluido en la página 16
stoRaGe & maintenanCe sPeCifiC maintenanCe: ENGINE: The engine instructions that accompany your unit detail specific procedures for maintenance of the engine. Following the engine manufacturer's recommendations will extend engine work life. PUMP: This unit is supplied with a maintenance free pump. NOZZLES: Nozzle orifices should be kept clean and free from obstructions. To clean nozzle orifice: . Disconnect the wand from the gun. . Insert the nozzle cleaner into the nozzle and rotate.
Resumen del contenido incluido en la página 17
stoRaGe & maintenanCe WinteRizinG: For storage and transportation purposes in subfreezing ambient temperatures, it will be necessary to winterize this unit. This unit must be protected to the WARNING lowest incurred temperature for the following reasons: RisK of unit buRstinG! 1. If any part of the pumping system becomes frozen; excessive pressure may do not sto Re/o PeRate unit in build up in the unit which could cause the unit to burst resulting in possible a fReezinG enViRonment! seriou
Resumen del contenido incluido en la página 18
tRoublesHootinG SYMPTOM PROBABLE CAUSE REMEDY Engine will not start. Various engine problems. Refer to the Engine Manual accompanying your unit. Unit components are frozen. Allow to thaw. If any part of the unit becomes frozen; excessive pressure may build up in the unit which could cause the unit to burst resulting in possible serious injury to the operator or bystanders. No discharge at nozzle when Inadequate water supply. Ensure hose is 3/4"
Resumen del contenido incluido en la página 19
statement of W aRRanty John Deere warrants all parts, (except those referred to below), of your new pressure washer to be free from defects in materials and workmanship during the following periods: For One () Year from the date of original purchase: Cart Assembly Plumbing High Pressure Pump GFCI For Ninety (90) days from the date of original purchase: Trigger Gun High Pressure Hose Strainer/Filters On/Off Switch Unloader Valve Defective parts not subject to normal wear an
Resumen del contenido incluido en la página 20
notes 0 Operator's Manual
