Resumen del contenido incluido en la página 1
Royal Sovereign LAMINATORS
OWNER'S MANUAL
RSH-1050/1650 ,RSR-685/1050
PLEASE READ AND SAVE INSTRUCTIONS
- 1 -
Resumen del contenido incluido en la página 2
TABLE OF CONTENTS TOPICS PAGE INSTRUCTION ----------------------------------------------------------------------- 3 SAFETY PRECAUTIONS ----------------------------------------------------------- 3 CHARACTERISTICS ----------------------------------------------------------------- 4 SPECIFICATIONS --------------------------------------------------------------------- 4 NAMES OF MAJOR PARTS OF MACHIN-------------------------------------------- 5 6~7 HOW TO INSTALL THE REWINDER ---
Resumen del contenido incluido en la página 3
INSTRUCTION Thank you for purchasing a Royal Sovereign Roll Laminator. It has been designed and manufactured to provide years of continuous service in the professional environment. To insure high quality lamination, please read this instruction manual thoroughly. This manual will provide you with complete operating and maintenance information. For additional product support or factory-direct ordering information. Call Royal Sovereign Customer Service at 1-800-397-1025. SAFETY PRECAUTIONS T
Resumen del contenido incluido en la página 4
CHARACTERISTIC RS Roll Laminator Line is advanced laminators with time transcendental design, utilizing the latest in laminating technology. It is designed for you to set temperature and speed as necessary and have the machine remember your settings. Also, you can laminate anything at high speed, regardless of thickness of material and type of film. Remote control device allows for control of the machine from the front or rear. Foot-Pedal Switch allows for hands-free operation. It is also desig
Resumen del contenido incluido en la página 5
NAMES OF MAJOR PARTS OF MACHINE 6 1 3 2 4 10 11 14 12 5 8 7 9 RSH-1650 RSH-1050 PART NAME RSR-1050 RSR-685 NO FRAME-GUIDE,PAPER 1 ○ ○ ○○ TAKE-UP SWITCH 2 ○○○ ○ TAKE-UP BOBBIN 3 ○○ ○ ○ IDLE BAR 4 ○ ○ ○ ○ TABLE-FRONT 5 ○ ○ ○ ○ HOT ROLLER ○ ○ X X 6 HOT METAL ROLLER X X ○ ○ ASS'Y-STAND 7 ○ ○ ○ ○ FOOT SWITCH 8 ○ ○ ○ ○ REMOTE CONTROL SWITCH 9 ○ ○ ○ ○ CONTROL PANEL 10 ○ ○ ○ ○ PRESSURE LEVER 11 ○ ○ ○ ○ TENSION CONTROL KNOB 12 ○ ○○ ○ FILM ALIGNMENT KNOB 13 X ○ ○○ SAFETY COVER ○ ○ ○ ○ 14 - 5 -
Resumen del contenido incluido en la página 6
How to install the rewinder 1. Disassemble both the Right cover and the Left cover. (Note :Turn the fastening nut of the Emergency switch counterclockwise and disaasemble the Emergency switch before disassembling the Right cover.) 2. Disassemble the Rear cover. 3. Disassemble the power switch bracket which is located at the left side of the machine. Power switch bracket M5 screw 6EA Plate-Rewinder L 4. Put the Plate-Rewinder L on the outer side of the frame as shown in the following
Resumen del contenido incluido en la página 7
take -up motor. Female Connector from Male Connector from take-up motor rewinder motor 7. Assemble the Right cover letting the wires go through the slot which is located at the rear side of the Right cover. 8. Put the Power switch bracket on the Plate-Rewinder L and fasten it with two M4 screws. Power switch bracket Plate-Rewinder L How to install the unwinder - 7 -
Resumen del contenido incluido en la página 8
1. Put the Plate-Unwinder R on the inner side of the frame as shown in the following figure and fasten it with four M6 hexagonal bolts. Plate-Unwinder R M6 hexagonal bolt 2. Put the Plate-Unwinder L on the inner side of the frame as shown in the following figure and fasten it four M6 hexagonal bolts. 주 주 름 름 L 방 방 C 지 지 D 부 부 표 시 창 열 열 판 판 버 튼 부 SETTING UP FILM - 8 -
Resumen del contenido incluido en la página 9
Picture 1 Picture 2 Upper Film Picture 3 Lower Film Picture 4 Upper Film Picture 5 Core Fixing Lower Film Screw 1. Set the glossy side of upper/lower film to face the heat. ( Glossy side is PET film and matte side is thermal polymer laminating film.) 2. Like picture 1, insert core into the left side of upper/lower film shaft. 3. Like picture 2 and 3, insert core into the right side of upper/lower film. 4. Like picture 4 and 5, adhere core closely. (Make the right/left direction of fixing s
Resumen del contenido incluido en la página 10
1. HOT FILM UPPER ROLL FILM UPPER ROLL FILM UPPER IDLE BAR UPPER IDLE BAR HOT METAL ROLLER HOT ROLLER ROLLER LOWER ROLL FILM LOWER ROLL FILM LOWER IDLE BAR LOWER IDLE BAR RSH-1050/1650 RSR-685/1050 1. Insert bar into the core of the roll film then place the bar on the machine. 2. Place the Pressure Lever (on the right side of machine) to the open mode at 15mm. 3. Insert a piece of wide cardboard (guiding paper/carrier) between the rollers. 4. Pull the film from the upper roller passing over
Resumen del contenido incluido en la página 11
TAKE UP DEVICE TAKE UP DEVICE COLD FILM COLD FILM PAPER BACK PAPER BACK HOT METAL ROLLER HOT ROLLER UPPER IDLE BAR UPPER IDLE BAR ROLLER PAPER BACK PAPER BACK LOWER IDLE BAR LOWER IDLE BAR RSH-1050/1650 RSR-685/1050 1. Set up cold film below the upper bar of the machine (Set the same as method of HOT film for protect paper of lower part) 2. Set the pressure Lever to the 15mm, open mode 3. Insert a piece of wide cardboard (guiding paper/carrier) between the rollers 4. Pull the film from the up
Resumen del contenido incluido en la página 12
***Methods of controlling pressure of the roller** 1. For setting, pull the pressure lever out and turn the lever to following the indication 2. Open/15mm : for laminating 15mm(0.6") thick board (RSH-1050/1650) 3. 10~13mm : for laminating 10~13mm （0.4" to 0.5") thick board 4. 5~7mm : for laminating 5~7mm(0.2" to 0.27") thick board 5. 1mm : for laminating 1mm(40mil) thick board 6. LAMINATING : for laminating 32~250micron thick film INSTRUCTIONS FOR CONTROL PANEL We designed this machine stan
Resumen del contenido incluido en la página 13
speed and temperature of rollers each by each by the LCD controller. And with memory function, you don’t need to set machine every time you laminate. ***Terms*** LCD DISPLY BUTTON 1.LCD WINDOW 1. Initial display status. - 13 -
Resumen del contenido incluido en la página 14
It displays you the last working condition when turned on. 2. Is displayed when the preset temperature is reached. 3. Blinking Indicates to wait till blinking stops. Current temperature is higher or lower than the preset temperature. 4. Saving electricity status. 5. Temperature 1) Shows the preset temperature 2) You can check the current temperature on the heat shoe by pressing T-Check 6. Speed *9 different speed option. "RSH" type---(S
Resumen del contenido incluido en la página 15
UPPER SPEED SPEED : Speed controller MEMORY LOWER MEMORY : Choose memorized working condition : ① Increase temperature COLD/HOT T-CHECK ST/BY ② Increase speed ③ Restore the memorized working setting STOP REV RUN : ① Decrease temperature MEAS RESET ② Decrease speed FAN ③ Restore the memorized working setting C/HOT : Cold and Hot mode change T-CHECK : Check current temperature ST/BY : Saving electricity while the machine is not being operated. REV : Reverse function
Resumen del contenido incluido en la página 16
Button & Display to 160°C (320°F). 2. Temperature setting of upper roller UPPER Press and you will see the LCD screen is blinking 6 times. Before blinking is finished, press or to set the temperature 3. Set temperature of lower roller LOWER Press and choose the arrow button the same way to set temperature of upper roller. UPPER 4 Each time you press the button, LOWER it will change 1°C (2°F). If you press the button more than
Resumen del contenido incluido en la página 17
1.Operator can memorize 9 working conditions. 2.Choose working condition by pressing and MEMORY button after pressing button. MEMOR and speed, press button. 3.It is memorized if buzzer is ringing with blinking. * If you change the temperature or speed when LCD MEMORY screen is still blinking, you have to press UPPER SPEED button after changing. LOWER MEMORY 4.When you memorize another working condition, you
Resumen del contenido incluido en la página 18
blink five times. 2.After this, it automatically returns to the previous state. T-CHECK ***Cold mode*** 1.You can do cold lamination with this function. C/HOT 2.Press the button to show "Cold" on the display. 3.Speed will always show 2. 4.Speed can be varied 1 or 4 by selecting button. 5.You release the machine from cold mode by C/HOT pressing button. 6.Everytime you press the button, buzzer is ringing SPEED 7.ST/BY mode is not working at COLD mode. M
Resumen del contenido incluido en la página 19
condition wouldn’t work. Press the button and ST/BY it will revert to the previous working. 3. When machine runs, you can’t change it to the mode. In this case, press the button and turn the STOP machine to the mode. ST/BY ***Check the laminating length & How many laminated papers*** MEAS 1. When press button the present numbers of length and papers laminated will be shown on the s
Resumen del contenido incluido en la página 20
2. Set the pressure lever to the “Laminating mode” 3. Increase roller temperature. If you already memorized special working condition, MEMORY press button and choose right condition by using or button. 4. When it’s ready, you will see ready sign on the screen and the buzzer will ring. RUN 5. Press the button. If rollers don’t run, check the emergency switch whether it is located at “ON” position or not. 6. To set film tens
