Manual de instrucciones de Tandberg Data 2U LTO

Resumen del contenido incluido en la página 1

StorageLoader 2U LTO
Quick Start Guide
Accessories — These accessories are included with your library
Power LVD SCSI 68-pin HD Ethernet Shipping Rack-mount kit Bar code labels**
cord to HD cable and LVD cable lock (fasteners and Multi-language packet
terminator* instructions included) and Warranty
* LVD SCSI configuration only. Important: Both LTO-2 and LTO-3 tape drives require Ultra 160 rated SCSI cabling, and an Ultra 3 or LVD 160 Active
SCSI terminator. The StorageLoader 2U LTO ship

Resumen del contenido incluido en la página 2

StorageLoader 2U LTO Quick Start Guide Step 1 — Before you begin 1 — Ensure that you have all the required items before you proceed (see Accessories and Additional Items on page 1). 2 — Locate an appropriate area for the unit that has adequate clearance for ventilation, minimal dust and debris, and an appropriate power source. The unit is designed for installation in a standard 4 post, 19-inch rack. 3 — Ensure that the work area is free from conditions that could cause electrostatic disch

Resumen del contenido incluido en la página 3

StorageLoader 2U LTO Quick Start Guide Step 4 — Powering on and Removing the Shipping Lock 1 — Power on the library by pressing the power switch on the back of the unit (press the I). When you apply power with the shipping lock installed, the library displays a message and ejects both left magazines. 2 — Pull the left magazine straight out of the library. 3 — Power the library off (press the 0). 4 — Remove the screw securing the shipping lock. Shipping Lock Page 3 of 8

Resumen del contenido incluido en la página 4

StorageLoader 2U LTO Quick Start Guide Step 4 continued — Powering on and Removing the Shipping Lock Important: Some views show the library with the top cover removed for clarity —DO NOT remove the top cover or you will void your warranty! 5 — Rotate the robot by pushing the lock handle toward the back of the library. This moves the TOP VIEWS FOR REFERENCE ONLY locking “tab” out from under the rail. a. Gently push the lock handle to the right approximately 1 inch (2.5cm). Import

Resumen del contenido incluido en la página 5

StorageLoader 2U LTO Quick Start Guide Step 5 — Adding bar code labels and loading cartridges 1 — Apply bar code labels to cartridges. CARTRIDGE 2 — Press the eject button to unlock the magazine (magazine releases and moves a short distance out of the library). This may take a few minutes. BARCODELABEL 3 — Pull the magazine straight out of the ENTRY/EXITPORT library (no side-to-side or up/down motion). EJECT 4 — Load cartridges in slots as shown. Note: The last two slots in eac

Resumen del contenido incluido en la página 6

StorageLoader 2U LTO Quick Start Guide Home Screen Menu and Buttons Home I/EPort Home Screen Exterior Buttons Function Buttons Function I/EPort Screen Release OK Accept the change I/E Port Unlock I/E Port Select Accept the choice Magazine Unlock magazine Back Return to previous screen LeftMagazine RightMagazine Eject Eject Home Screen Menu Maint Drive Move Lib (Maintenance/ (Tape Drive (Move Cartridges) (Library Properties) Diagnostics) Properties) Load Drive(s) Library ID Library Maint

Resumen del contenido incluido en la página 7

StorageLoader 2U LTO Quick Start Guide Troubleshooting Tips • Is the power cord inserted correctly and is the power switch on (press the I on the If the library did not power back of the unit)? on as described • Did you remove the shipping key? If the library displays an Refer to the Product Manual for a list of error messages and corrective actions. error on the front panel • Host adapter card installation—Make sure that you installed your host adapter card correctly, that the card i

Resumen del contenido incluido en la página 8

StorageLoader 2U LTO Quick Start Guide Additional Information Contact Tandberg Data for general information, sales, service and support at: www.tandbergdata.com Always check the website for the most up to date information. IMPORTANT! Before moving or shipping the library, you must first “Park the Robot” and replace the shipping key or you will void your warranty. • From the library’s front panel, press the Maint / Library Maintenance / Park the Robot buttons. • After you receive the confirm