Resumen del contenido incluido en la página 1
Installation and Operating Manual
Models 5660(I)
Tested &
Listed By
Report #:
215‐S‐32‐4and215‐S‐33‐4
Safety Notice
Please read this entire manual before installation and use of this pellet fuel‐burning room heater. Failure to follow
instructions may result in property damage, bodily injury, or even death.
If your heater is not properly installed, a house fire may result. For everyone’s safety, FOLLOW all Installation and
Operating Directions. Never use makeshift compromises d
Resumen del contenido incluido en la página 2
TABLE OF CONTENTS Topic Page(s) Introduction 3 Safety Information 4‐5 Specifications 6 Dimensions 6‐7 Operating Instructions 8‐11 Thermostat Installation 12 Clearances to Combustibles 13 Installing Your Room Heater 14‐23 Mobile Home Installations 24 Insert Pellet Stove Installation 25‐28 Vent Termination Locatio
Resumen del contenido incluido en la página 3
Introduction The entire family of United States Stove Company thanks you for purchasing your new pellet burning room heater. At U.S. Stove, we build all of our products with a hands‐on approach to detail and quality. Our old world team of Craftsmen take great pride in their superior workmanship to ensure you have years of trouble free use of your pellet heater. U.S. Stove Pellet Burning Room Heaters have been tested and listed for installation in residential, mobile home and alcove
Resumen del contenido incluido en la página 4
SAFETY INFORMATION Be sure to read the entire owner’s manual prior to installing and operating this Pellet heater. Failure to follow these instructions could result in fire, property damage, bodily injury or even Death. This stove’s exhaust system works with negative combustion chamber pressure and a slight positive chimney pressure, it is extremely important to ensure that the exhaust system be sealed and airtight. The ash pan and viewing door must be securely fastened in order for the
Resumen del contenido incluido en la página 5
SAFETY INFORMATION ‐ continued Keep foreign objects out of the hopper. Contact your local building officials to obtain a permit and information on any installation restrictions or inspection requirements in your area. Be sure to notify your insurance company of your new U.S. Stove Pellet Burning Room Heater. Allow the Pellet Stove Room Heater to cool before performing any maintenance. Ashes must be disposed of in a metal container with a tight lid and placed on a noncombu
Resumen del contenido incluido en la página 6
SPECIFICATIONS Heating Specifications: Burn Rate: *43,900 btu’s per hour or 5.1 lbs. of fuel per hour Hopper Capacity: 55 lbs. *Dependent upon quality and heating value of pellet fuel. DIMENSIONS Figure 1 6
Resumen del contenido incluido en la página 7
DIMENSIONS ‐ continued The minimum installation dimensions, of the insert opening, are: 32” (813mm) wide x 22‐3/4” (578mm) high x 12‐1/4” (311mm) deep. Figure 2 7
Resumen del contenido incluido en la página 8
OPERATING INSTRUCTIONS Check and Fill the Fuel Hopper with Pellets: This Pellet Stove is available as a freestanding unit or as a fireplace insert. There is a different method for filling the hopper for each type of heater: To check and fill the hopper of the freestanding heater, simply lift the hopper door, visually check the hopper and add pellets when needed. To check and fill the hopper of the insert heater, pull hopper lid forward, visually check the hopper and add pellets whe
Resumen del contenido incluido en la página 9
OPERATING INSTRUCTIONS ‐ continued When the pellets have ignited and flame has been established, the start‐up cycle will end; this procedure takes between 8 and 12 minutes. If the control is set to Manual Mode, it will now default to the heat level setting the last shutdown time. If the control is set to T‐STAT Mode the heat output will coincide to the commands from the thermostat. Auger: As explained in the starting up step, this button is only served to start up the pellet sto
Resumen del contenido incluido en la página 10
OPERATING INSTRUCTIONS ‐ continued Control Board Functions: MODE Button: The MODE button allows you to switch operating mode on your Pellet Stove Room Heater. Depress the MODE button to switch between Manual and T‐STAT modes. As you depress the MODE button the indicator light above the desired mode will engage. When you engage the Manual mode, you will be able to manually select the heat settings. If you have installed a remote thermostat for your Pellet Stove Room Heater and wis
Resumen del contenido incluido en la página 11
OPERATING INSTRUCTIONS ‐ continued the Auger feed rate will help keep the flames from extinguishing on the minimum heat level setting. You can also use the AUGER TRIM button to lower heat output on the minimum heat level setting: Depress and release the AUGER TRIM button until the heat level 1 and 5 setting lights appear to slightly increase the feed rate on the minimum heat level. Depress and release the AUGER TRIM button until the heat level 1 and 4 setting lights appear to slightl
Resumen del contenido incluido en la página 12
THERMOSTAT INSTALLATION Optional thermostats are available for use with your pellet stove. A thermostat can help you maintain a constant room temperature. The thermostat option will require the installation of a millivolt type thermostat. NOTE: Your thermostat should be installed by an authorized dealer or service person. Installation of Remote Thermostat: Disconnect Pellet Stove Room Heater unit from power supply. Open right side panel to gain access to rear of control panel
Resumen del contenido incluido en la página 13
CLEARANCES TO COMBUSTIBLES INSTALL ALL VENTS AT CLEARANCES SPECIFIED BY THE VENT MANUFACTURER! When your Pellet Stove Room Heater is being installed on a combustible floor it is mandatory that a 1/2" (13mm) thick non‐combustible hearth pad be installed under the heater. The non‐combustible hearth pad must extend at least 6” beyond the fuel loading and ash removal openings and at least the depth of the heater plus 6 inches (152mm) out in front of the heater. This applies to both freestand
Resumen del contenido incluido en la página 14
INSTALLING YOUR ROOM HEATER You have already made the important decision of choosing your U.S. Stove Pellet Burning Room Heater; now your next step is to determine where to install your new pellet stove heater. To get the most efficient use of re‐circulated heat, you should consider a room that is centrally located within your home. Choose a room that is large and open. It is Extremely Important to maintain proper clearances from any combustible surfaces or materials in the room w
Resumen del contenido incluido en la página 15
INSTALLING YOUR ROOM HEATER ‐ continued HORIZONTAL EXHAUST VENT INSTALLATION 1. Locate your pellet stove in a location which meets the requirements of this manual, but in an area where it does not interfere with the house framing, wiring, etc. 2. Install a non‐combustible hearth pad underneath the pellet stove. This pad should extend at least 6” (152mm) in front of the unit. 3. Place the pellet stove approximately 15” (381mm) away from the interior wall. 4. Locate the center of the ex
Resumen del contenido incluido en la página 16
INSTALLING YOUR ROOM HEATER ‐ continued HORIZONTAL EXHAUST VENT INSTALLATION 16
Resumen del contenido incluido en la página 17
INSTALLING YOUR ROOM HEATER ‐ continued FREESTANDING INTERIOR VERTICAL INSTALLATION 1. Locate your Pellet Stove Room Heater in a location which meets the requirements of this manual, but in an area where it does not interfere with the house framing, wiring, etc. 2. Install a non‐combustible hearth pad underneath the pellet stove. This pad should extend at least 6” (152mm) in front of the unit. 3. Place your Pellet Stove Room Heater on the hearth pad and locate the unit in manner that wi
Resumen del contenido incluido en la página 18
INSTALLING YOUR ROOM HEATER ‐ continued FREESTANDING EXTERIOR VERTICAL INSTALLATION 1. Locate your Pellet Stove Room Heater in a location which meets the requirements of this manual, but in an area where it does not interfere with the house framing, wiring, etc. 2. Install a non‐combustible hearth pad underneath the pellet stove. This pad should extend at least 6” (152mm) in front of the unit. 3. Place your Pellet Stove Room Heater on the hearth pad and locate the unit in manner that wil
Resumen del contenido incluido en la página 19
19
Resumen del contenido incluido en la página 20
INSTALLING YOUR ROOM HEATER ‐ continued SELKIRK DIRECT‐TEMP VENT SYSTEM FOR PELLET STOVE HEATERS Images courtesy of Selkirk 20
