Resumen del contenido incluido en la página 1
SHERWOOD INDUSTRIES IS AN ENVIRONMENTALLY RESPONSIBLE COMPANY. THIS MANUAL IS PRINTED ON RECYCLED PAPER.
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
Sienna
B Y : S H E R W O O D I N D U S T R I E S L T D
OWNER’S MANUAL
WHAT TO DO IF YOU SMELL GAS
This appliance is
only for use with
• Open windows/extinguish any open flame.
the type of gas
• Do not try to light any appliance.
indicated on the
• Do not touch any electrical switch or use any
rating plate. This
phone in your building.
Resumen del contenido incluido en la página 2
Safety Precautions FOR SAFE INSTALLATION AND OPERATION OF YOUR “ENVIRO” HEATER, PLEASE CAREFULLY READ THE FOLLOWING INFORMATION: • All ENVIRO gas-fired appliances must be installed • To prevent injury, do not allow anyone who is in accordance with their instructions. Carefully read all unfamiliar with the stove to operate it. the instructions in this manual first. Consult the building • To prevent injury, if the pilot or pilot and authority having jurisdiction to determine the need for burn
Resumen del contenido incluido en la página 3
Table of Contents Safety Precautions.....................................................................................................2 Table of Contents......................................................................................................3 Codes And Approvals.................................................................................................4 Specifications............................................................................................................
Resumen del contenido incluido en la página 4
Codes And Approvals DIRECT VENT: This type is identified by the suffix DV. This appliance draws all of its air for combustion from outside the dwelling, through a specially designed vent pipe system. This appliance has been tested and approved for installations from 0 feet to 4500 feet (1372 m) above sea level. BV: This Vented appliance draws all of its combustion air from the dwelling and must be vented using listed B or L vent. May also be vented through a conventional chimney using a chimne
Resumen del contenido incluido en la página 5
Specifications RATING LABEL LOCATION: The rating label is located under the control panel and is attached to a rectangular metal sheet that is chained to the fireplace. DIMENSIONS: Table 1: Sienna exterior dimensions. (Shaded dimensions shown in Figure 1 & 2.) Surround Style Distance Direct Vent B-Vent 11 9 Arched Surround From Flue To Surround 14 /16” (376 mm) 14 /16” (370 mm) 5 From Back/Sensor To Surround 17 /16” (439 mm) 18 7⁄8” (479 mm) 33” x 46” (840 x 1930 mm) From Flue To Surround 14 1⁄
Resumen del contenido incluido en la página 6
Specifications 21" ( 5 33 m m ) S en s or S how n : B - V e n t w i th 3 3 " x 4 6" ( 84cm x 193 c m ) sur r ou nd pan e l w i t h t r i m F l u e 3 1 7 / 8 " ( 441 m m ) 1 13 / 1 6 " ( 333 m m ) 1 3 W i t h T r i m 4 6 / 8 " ( 1 17 1 m m ) 1 / 8 " W i tho ut T r i m 46" ( 1 16 8 m m ) ( 36 m m ) W i th T r i m 3 3 3 / 1 6 " ( 3 4 3 m m ) W i th o u t T r i m 3 3 " ( 3 3 8 m m ) 1 30 / 2 " ( 7 75 m m ) 11 3 22 / 16 " 2 2 / 4 " 1 ( 576 m m ) ( 5 77 m m ) 15 / 1 6 " ( 38 3 m m ) 5 2 0 / 8 " ( 5 2
Resumen del contenido incluido en la página 7
L O I P T O L T P T H T P T H I P F F Operating Instructions For Your Safety, Read Safety Precautions And Lighting Instructions Before Operating WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY A FIRE OR EXPLOSION MAY RESULT, CAUSING PROPERTY DAMAGE, PERSONAL INJURY OF LOSS OF LIFE. PILOT LIGHTING INSTRUCTIONS: H o t wh i l e o p e r a t i n g . D o n o t t o u c h , s ever e b u r n s m ay r e su lt . K e ep c h i l d r e n , cl o t h ing , C A U T I O N : f u r n i t u r e , g a so l
Resumen del contenido incluido en la página 8
Operating Instructions For Your Safety, Read Safety Precautions And Lighting Instructions Before Operating BURNER LIGHTING: A) Make sure the pilot is lit. B) Turn gas control knob COUNTER CLOCKWISE to ON. C) Flip the burner switch to ON. D) Turn HI/LO knob to the desired flame height. E) Turn on all electrical power to the unit. NOTE: Check that all burner holes are lit. Figure 5. Control panel. TURN OFF UNIT: Flip switch to OFF to turn off burners only. If the fireplace is to be turned off
Resumen del contenido incluido en la página 9
Maintenance And Service Warning: Failure to position the parts in accordance with this manual, or failure to use only parts specifically approved with this appliance, may result in property damage or personal injury. At least once a year, run through the following procedures to ensure the system is clean and working properly. Check the burner to see if all the ports are clear and clean. Check the pilot to make sure it is not blocked by anything. The pilot flame should be blue with little or
Resumen del contenido incluido en la página 10
Maintenance And Service TO BE INSTALLED BY A QUALIFIED SERVICE AGENCY ONLY FUEL CONVERSION: Warning: This conversion kit shall be installed by a qualified service agency in accordance with the manufacturer’s instructions and all applicable codes and requirements of the authority having jurisdiction. If the information in these instructions is not followed exactly, a fire, explosion or production of carbon monoxide may result causing property damage, personal injury or loss of life. The qual
Resumen del contenido incluido en la página 11
Initial Installation WARNING: Operation of this heater when not connected to a properly installed and maintained venting system can result in carbon monoxide (CO) poisoning and possible death. CLEARANCES TO COMBUSTIBLES: Maintain sufficient clearances for operation, service and maintenance. • A clearance of 25 1⁄2” (648 mm) minimum is required from the center of the unit to the sidewalls. • A 2” (51 mm) wide mantel can be mounted at a 1 0" ( 254m m) M an t l e minimum height of 39” (991 mm) fr
Resumen del contenido incluido en la página 12
Initial Installation WARNING: Operation of this heater when not connected to a properly installed and maintained venting system can result in carbon monoxide (CO) poisoning and possible death. MINIMUM FIREPLACE SIZE: Table 2: Minimum dimensions of fireplace for Sienna to be installed into. Description of Fireplace Dimension Direct Vent B-Vent At Back 23 1⁄4” (591 mm) 23 1⁄4” (591 mm) Width At Front 35” (889 mm) 35” (889 mm) With Surround Only 23 3⁄4” (603 mm) 23 3⁄4” (603 mm) Height With Surro
Resumen del contenido incluido en la página 13
Initial Installation QUALIFIED INSTALLERS ONLY DIRECT VENT MODEL: WARNING: This appliance has been designed to draw room air for proper heat circulation from the sides of the unit. Blocking or modifying the louvers in any way can create hazardous situations. This model is vented with two (2) 3” aluminum or stainless steel flex vent leading into a co-linear to co-axial vent adaptor and using a vertical termination cap. The flue collars of this model will fit inside of standard 3” vent and ma
Resumen del contenido incluido en la página 14
Initial Installation QUALIFIED INSTALLERS ONLY VENTING FIREPLACE INSERTS: The ENVIRO SIENNA may be installed and vented into any solid fuel fireplace that has been installed in accordance with the National, Provincial/State and local building codes and has been constructed of non- combustible materials. Before starting refer to PREPARING YOUR SIENNA FOR INSTALLATION and CONVERTING A DIRECT VENT FIREPLACE TO A B-VENT FIREPLACE. An approved chimney liner and rain cap must be used. A throat conne
Resumen del contenido incluido en la página 15
Initial Installation QUALIFIED INSTALLERS ONLY ELECTRICAL REQUIREMENTS: The fan is thermostatically controlled and it will o o 1 2 0 F ( 4 9 C ) not operate if the appliance is cold. A few minutes T e m p e r a t ur e S e n sor F a n C o n t r o l after the appliance is lit and the variable speed control is set at a desired setting, the fan will C N T4 C N T 1 automatically turn on. The fan will automatically B l a c k turn off after the appliance has cooled down. W hi te The fireplace must
Resumen del contenido incluido en la página 16
L O I P T O L T P T H T P T H I P F F Initial Installation QUALIFIED INSTALLERS ONLY GAS LINE CONNECTION: Warning: Only persons licensed to work with gas piping may make the necessary gas connections to this appliance. Gas Line Connection: •This fireplace is equipped with a certified flexible pipe located on the right side of the unit, terminating in a 3⁄8” male NPT fitting. Consult the local authorities for local codes or use the CAN/CGA B149 (1 or 2) installation code in Canada. In the U
Resumen del contenido incluido en la página 17
Initial Installation QUALIFIED INSTALLERS ONLY CONVERTING A DIRECT VENT FIREPLACE TO A B-VENT FIREPLACE: 1. Remove the Direct Vent chimney connector assembly by taking out the two (2) T-20 screws at the front of the unit. Push the assembly out from under the brackets at the back and remove (see Figure 16). Di r e ct V e n t 2. Remove the two (2) fresh air C o n ne c t or A s s e m bl y inlet covers from each side. Cover locations shown in Figure 16. 3. Slide the B-Vent chimney connect
Resumen del contenido incluido en la página 18
Secondary Installation QUALIFIED INSTALLERS ONLY REPLACING THE BLOWER: 1. Turn the unit off and allow the unit to cool completely. 2. Remove the fascia or louvers, open the door (see “DOOR REMOVAL”), and remove the log set. 3. Remove the log support tray by lifting the back of the tray up and pull it out from under the lip. Take care to not knock the pilot and the side brick panels. 4. Remove the centre and top brick panels (see “REMOVING THE BRICK PANEL”). 5. Turn gas supply off and remove ga
Resumen del contenido incluido en la página 19
Secondary Installation DOOR REMOVAL: Open the door by removing the 5 two (2) /16’’ bolts located at the top outside corners of the glass frame (see Figure 19). Lift the bottom of the door up and remove from unit (see Figure 20). CAUTION GLASS MAY SEPARATE FROM DOOR. Figure 20: Bottom hooks for glass Figure 19: Top bolts for glass door. door. INSTALLATION OF SURROUND PANEL: The Sienna must have one of the panels installed around the unit; the unit panel, the filler panel, or the filler pa
Resumen del contenido incluido en la página 20
Secondary Installation LOG SET AND EMBER INSTALLATION: NOTE: The logs are fragile and should be handled gently. The placement of the logs is not arbitrary. If they are positioned incorrectly, the flames can be “pinched” and will not burn correctly. The burner, and a few of the logs come with locator pins, notches and ledges, which make alignment easier. Using the pictures provided, carefully set the logs in place (see Figures 24 through 29). Figure 24: The first log to be placed is the bac
