Resumen del contenido incluido en la página 1
1
INSTALLER: THESE INSTRUCTIONS MUST BE CONVEYED TO AND REMAIN WITH THE HOMEOWNER.
INSTALLATION AND
OPERATION INSTRUCTIONS
CERTIFIED UNDER CANADIAN AND AMERICAN NATIONAL STANDARDS: CSA 2.22, ANSI Z21.50 FOR VENTED GAS FIREPLACE.
GT8N
NATURAL GAS
GT8P
PROPANE
Certified for Canadian and United States using ANSI/CSA Methods.
SAFETY INFORMATION
WARNING: If the information in these instructions
are not followed exactly, a fire or explosion may result
causing property damage, personal injury or loss
Resumen del contenido incluido en la página 2
2 TABLE of CONTENTS PG 2-5 INTRODUCTION 10 FINISHING Warranty Door Removal Dimensions Glass Removal General Instructions Frame Installation General Information Light Installation Care of Glass & Plated Parts 11 OPERATING INSTRUCTIONS 5-6 VENTING 12 MAINTENANCE Venting Lengths Gas Pressure Adjustment Air Terminal Locations Venturi Adjustment 7-9 INSTALLATION/FRAMING 13 REPLACEMENTS W all & Ceiling Protection Replacement
Resumen del contenido incluido en la página 3
3 NAPOLEON® products are manufactured under the strict Standard of the world recognized ISO 9001 : 2000 Quality Assurance Certifi cate. NAPOLEON® products are designed with superior components and materials, assembled by trained craftsmen who take great pride in their work. The burner and valve assembly are leak and test-fi red at a quality test station. The complete fi replace is thoroughly inspected by a qualifi ed technician before packaging to ensure that you, the customer, receives the qua
Resumen del contenido incluido en la página 4
4 FIGURE 1 16 1 /4 3 /4 Minimum clearance to combustible construction from GENERAL INSTRUCTIONS fi replace and vent surfaces: THIS GAS FIREPLACE SHOULD BE INSTALLED AND Fireplace framing: - 6” to top SERVICED BY A QUALIFIED INSTALLER to conform with - 0” to stand-offs (rear and sides) local codes. Installation practices vary from region to region Vent pipe: - 1” and it is important to know the specifi cs that apply to your Recessed depth: - 7” area, for example: in Massachusetts State: •
Resumen del contenido incluido en la página 5
5 CARE OF GLASS, AND PLATED PARTS WARNING DO NOT SUBSTITUTE MATERIALS. USE CARE WHEN HANDLING GLASS COMPONENTS DO NOT STIKE, OR SLAM SHUT. DO NOT OPERATE WITH BROKEN GLASS. The glass is 3/16” ceramic glass available from your Napoleon® / Wolf Steel Ltd. dealer. Clean the glass after the fi rst 10 hours of operation with a recommended gas fi replace glass cleaner. Thereafter clean as required. DO NOT CLEAN GLASS WHEN HOT! Do not use abrasive cleaners to clean plated parts. Buff lightly with
Resumen del contenido incluido en la página 6
6 FIGURE 3 H M C H F J B A N K L G B W415-0619 / A /08.09.07
Resumen del contenido incluido en la página 7
7 INSTALLATION / FRAMING WALL AND CEILING PROTECTION This application occurs when venting through an exterior wall. FIGURE 4 Having determined the air terminal location, cut and frame a hole in an exterior wall with a minimum square opening of 8” W x 8” H. IMPORTANT: For optimum performance, The vent pipe should rise ¼” per foot of run. 1. Apply a bead of caulking all around and place the fi restop spacer over the framework to restrict cold air from being drawn into the room or around the
Resumen del contenido incluido en la página 8
8 FIREPLACE VENT CONNECTION GAS INSTALLATION Proceed once the vent installation is complete. 1. Install the 3” diameter vent pipe to the fi replace. Secure Note : All gas connections must be contained within with 3 screws and fl at washers. Seal the joint and screw holes the fi replace when complete. using Mill Pac sealant (W573-0007 not supplied). 2. Install the 5” diameter vent pipe to the fi replace. Attach 3 1. The fi replace is designed to accept a /8” gas supply and seal the joints. 3 lin
Resumen del contenido incluido en la página 9
9 NAILING TAB INSTALLATION CLEARANCES TO COMBUSTIBLES To install the fi replace face MAINTAIN THESE MINIMUM CLEARANCES TO fl ush with the fi nished surface, COMBUSTIBLES: position the framework to Fireplace framing - 6” to top accomodate the thickness of - 0” to stand-offs (rear and sides) the fi nished surface. Use 4 Fireplace fi nishing - 0” self tapping screws to secure the nailing tabs to the 2 x 4’s. Cover the nailing tabs with your fi nishing material. FIGURE 14 ELECTRICAL CONNECTI
Resumen del contenido incluido en la página 10
10 FINISHING 5. If required, the bottom DOOR REMOVAL trim bracket can be adjusted Before the glass door can be removed, the optional front by loosening it’s securing must be removed. screws. (FIGURE 19) Once TM the Torch frame is perfectly The glass door is secured to the top front edge of the fi rebox. square and the control door Pull the handles of the latches forward, then lift the hooks out assembly will close without from the slots in the door frame to release the top of the door
Resumen del contenido incluido en la página 11
11 OPERATING INSTRUCTIONS When lit for the fi rst time, the fi replace will emit a slight slight odour for a few hours. This is caused by dust particles in odour for a few hours. This is a normal temporary condition the heat exchanger burning off. Open a window to suffi ciently caused by the curing of paints and lubricants used in the ventilate the room. manufacturing process and will not occur again. Simply open Purge all gas lines with the glass door of the fi replace a window to suffi ciently
Resumen del contenido incluido en la página 12
12 MAINTENANCE TURN OFF THE GAS AND ELECTRICAL POWER BEFORE 2. Check to see that the main burner ignites when the SERVICING THE FIREPLACE. switch for the burner is turned on. A 5 second light-up CAUTION: Label all wires prior to disconnection when period is satisfactory. If ignition takes longer, consult your servicing controls. Wiring errors can cause improper and Napoleon® dealer / distributor. dangerous operation. Verify proper operation after servicing. 3. Check that the gasketing on the s
Resumen del contenido incluido en la página 13
13 REPLACEMENTS Contact your dealer for questions concerning prices and 1. MODEL & SERIAL NUMBER OF FIREPLACE availability of replacement parts. Normally all parts can be 2. INSTALLATION DATE OF FIREPLACE ordered through your Napoleon® dealer or distributor. 3. PART NUMBER When ordering replacement parts always give the following 4. DESCRIPTION OF PART information: 5. FINISH * IDENTIFIES ITEMS WHICH ARE NOT ILLUSTRATED. FOR FOR WARRANTY REPLACEMENT PARTS, A PHOTOCOPY OF FURTHER INFORMA
Resumen del contenido incluido en la página 14
14 TROUBLE SHOOTING GUIDE BEFORE ATTEMPTING TO TROUBLESHOOT, PURGE YOUR UNIT AND INITIALLY LIGHT THE IGNITOR AND THE MAIN BURNER WITH THE GLASS DOOR OPEN. SYMPTOM PROBLEM TEST SOLUTION Electrode sparks, burner ignites, electrode Hot and neutral wires are reversed - Connect the hot wire to the black wire. Connect the neutral wire to contiunes to spark for at control module. the white wire. complete 7 seconds, burner shuts down. Main burner fl ame is a - Remove blockage. In extremely cold
Resumen del contenido incluido en la página 15
15 W415-0619 / A / 08.09.07 Fireplace Service History This fireplace must be serviced annually depending on usage SPECIAL CONCERNS DATE DEALER NAME SERVICE TECHNICIAN NAME SERVICE PERFORMANCE
Resumen del contenido incluido en la página 16
16 NOTES W415-0619 / A /08.09.07
