Resumen del contenido incluido en la página 1
DO NOT
DISCARD
R
2700-I ACT WOOD INSERT
Advanced Combustion Technology (ACT)
Model:
Portland
Tested and
O-T L
Listed by Oregon USA
C US
OMNI-Test Laboratories, Inc.
2700-I
NOTICE
DO NOT DISCARD THIS MANUAL
• Read, understand and • Leave this manual with
• Important operating
follow these instructions
and maintenance party responsible for
for safe installation and use and operation.
instructions included.
operation.
WARNING
WARNING
HOT SURFACES!
If the information in these
instructions is
Resumen del contenido incluido en la página 2
R 2700-I WOOD INSERT (ACT) and Welcome to the Quadra-Fire Family! Hearth & Home Technologies welcomes you to our tradition of we are old-fashioned when it comes to craftsmanship. Each unit is excellence! In choosing a Quadra-Fire appliance, you have our meticulously fabricated and surfaces are hand-finished for lasting assurance of commitment to quality, durability, and performance. beauty and enjoyment. Our pledge to quality is completed as each model undergoes a quality control inspe
Resumen del contenido incluido en la página 3
R 2700-I WOOD INSERT (ACT) TABLE OF CONTENTS pARTS & ACCESSORIES LIST --------------------- 22 SAFETY & OVERVIEW OF AppLIANCE Location of Serial Number Label ------------------------- 2 WARRANTY pOLICY ------------------------------------ 25 Dimensions ----------------------------------------------------- 4 SERVICE & MAINTENANCE LOG ----------------- 26 Minimum Clearances to Combustibles ------------------ 4 Listings ---------------------------------------------------------- 5 CONTACT INFORMAT
Resumen del contenido incluido en la página 4
R 2700-I WOOD INSERT (ACT) DIMENSIONS CLEARANCES TO COMBUSTIBLES United States and Canada 26-1/16" (681mm) 18-1/2" 470mm) Maximum Mantel Depth - 10 inches (254mm) Mantel C L 17-1/16" (4mm) B Trim 12-5/8" (21mm) 5-5/16" (15mm) C A D Insert Figure 4.1 Top View E F Hearth Extension 4-1/16" Omni Report #060-S-52-2 (10mm) USA CANADA A Sidewall to Stove 14" (356mm) 1 4" (356mm) B Mantel to Stove 2 1" (533mm) 21" (533mm) C *Top Trim to Stove 14" (356mm) 14" (356
Resumen del contenido incluido en la página 5
R 2700-I WOOD INSERT (ACT) LISTINGS CHIMNEY HEIGHT/DRAFT (CONT’D) These installation instructions describe the installation and opera- AVOID FIRE: To ensure that insulation or any other combustible tion of the Quadra-Fire 2700-I Wood Insert. This insert meets the material does not contact the chimney, a chimney inside the house U.S. Environmental Protection Agency’s 1990 particulate emission must have at least 2 inches (51mm) of air space clearance around standards. The 2700-I is listed
Resumen del contenido incluido en la página 6
R 2700-I WOOD INSERT (ACT) CALCULATING ALTERNATE DESIGN, INSTALLATION & LOCATION FLOOR pROTECTION Consideration must be given to: Material • Safety • Convenience Thermal Conductivity: k value • Traffic flow The k value indicates the amount of heat (in BTU’s) that will flow • Chimney and chimney connector required in 1 hour through 1 square foot of a uniform material 1 inch thick It is a good idea to plan your installation on paper, using exact for each degree (F) of temperature diffe
Resumen del contenido incluido en la página 7
R 2700-I WOOD INSERT (ACT) CHIMNEY REqUIREMENTS OVALIZING ROUND STAINLESS STEEL LINERS WARNING Ovalizing round stainless steel liners to accommodate the liner passing through the damper region of a fireplace is an Fire Risk. allowable and acceptable practice. Follow Chimney Connector Manufacturer’s Ensure that the ovalization is minimized to the extent Instructions for Proper Installation. required to fit through the damper. ONLY use connector: • Within the room, between appliance and c
Resumen del contenido incluido en la página 8
R 2700-I WOOD INSERT (ACT) 1. An outside air inlet must be provided for combustion and INSTALLATIONS INTO MOBILE HOMES must remain clear of leaves, debris, ice and/or snow. It 1. An outside air inlet must be provided for combustion. See must be unrestricted while unit is in use to prevent room page 12 for installation information. air starvation which can cause smoke spillage and an 2. Appliance must be secured to the mobile home structure inability to maintain a fire. Smoke spillag
Resumen del contenido incluido en la página 9
R 2700-I WOOD INSERT (ACT) MASONRY FIREpLACE Masonry USING DIRECT-CONNECT METHOD Chimney Flue Tile The Quadra-Fire 2700-I Insert conforms with the UL Stan- Full Listed Mantel Liner Option dard for Safety 1482 and ULC S628 (Canada) in all respects, and is approved to UL & ULC safety standards for installa- Direct Connect tion and use within a fireplace with a masonry chimney in Seal Option Damper accordance with NFPA 211, with a direct flue collar connec- Area tion. A starter pipe is
Resumen del contenido incluido en la página 10
R 2700-I WOOD INSERT (ACT) FACTORY BUILT ZERO CLEARANCE FIREpLACE (USA INSTALLATIONS ONLy) The Quadra-Fire 2700-I Insert is listed to UL 1482 Standard and is approved for installation into listed factory-built zero Masonry clearance fireplaces listed to UL 127 conforming to the follow- Chimney ing specifications and instructions: Flue Tile Full Listed The original factory-built clearance fireplace chimney cap Mantel Liner Option must be re-installed after installing the approved chim-
Resumen del contenido incluido en la página 11
R 2700-I WOOD INSERT (ACT) INSTALLATION IN CANADA LEVELING LEGS MASONRY and HEAT-CIRCULATING 1. Remove the 2 screws already installed on each leg. (INSTALLATIONS INTO FACTORY-BUILT FIREPLACES ARE 2. Move legs to the desired height. PROHIBITED IN CANADA) . Re-install the screws to secure in place. Whether installed in a masonry or heat-circulating fire- place, this fireplace insert must be installed with a continu- ous chimney liner of 6 inches (152mm) diameter extending from the fir
Resumen del contenido incluido en la página 12
R 2700-I WOOD INSERT (ACT) OUTSIDE AIR INSTALLATION OpTIONAL qUICK CONNECT COLLAR If you would like to use the Quick Connect Collar for easy The Outside Air Cover Boxes must be installed flue installation and removal, follow the directions below. on both panel legs FIRST before installing the panels on the insert. The boxes are included 1. Attach venting to Quick Connect Collar. Secure with 2 with the panel and Trim Kit Assembly. screws. 2. Remove baffle and ceramic blanket. See page 20
Resumen del contenido incluido en la página 13
R 2700-I WOOD INSERT (ACT) pANEL and TRIM SET Attaching Panels and Trim to the Insert 1. Remove the insert top (if installed) by lifting up slightly The Outside Air Cover Boxes must be installed then pulling towards you and set aside. See Figure 14.1 on both panels legs FIRST before installing the on page 14. panels on the insert. See page 12. 2. There are 2 locator pins on the top of the insert to match up with alignment holes on the back flange of the panel Included in Kit: (2) side
Resumen del contenido incluido en la página 14
Blower Cover R 2700-I WOOD INSERT (ACT) TOp INSTALLATION INSTRUCTIONS The top is packaged separately and shipped with the insert. Install on insert after unit is in place and the installation of the panels and trim are complete. Push the top into place by aligning the pins into the slots and then press down into position. panel Top Blower Motor Top Ashlip Blower cord may be attached on the left or right side Figure 14.1 BLOWER INSTALLATION Figure 14.2 Included in Kit: Blower motor an
Resumen del contenido incluido en la página 15
R 2700-I WOOD INSERT (ACT) ZERO CLEARANCE ADJUSTABLE TRIM SUPPORT, 2 inch to 10 inch EXpLODED VIEW OF SCISSORS Included in Kit: 1 trim top; 1 trim front; 2 trim sides; double-sided tape (already installed) Tools Required: Phillips head screw driver; sheet metal SCREWS ARE CIRCLED shears; measuring tape; gloves CAUTION DOUBLE-SIDED TAPE DOUBLE-SIDED TAPE Injury Risk. Figure 15.1 • Gloves recommended • May have sharp edges 1. The 10 screws on each set of scissors will already be EXPAND SC
Resumen del contenido incluido en la página 16
R 2700-I WOOD INSERT (ACT) OpERATION 2. Place several wads of crushed paper on the firebox floor. WOOD SELECTION AND STORAGE . Open Start-Up Air Control (right control) and Primary Air Control (center control under ashlip) fully. Figure 18.1 Burn only dry seasoned wood. Dry, well-seasoned wood will on page 18. not only minimize the chance of creosote formation but will give you the most efficient heat output. Even dry wood con- 4. Ensure that no matches or other combustibles are in
Resumen del contenido incluido en la página 17
R 2700-I WOOD INSERT (ACT) OpERATING TIpS BURN RATES (Cont’d) For maximum operating efficiency with the lowest emissions, LOW: Gradually close down the Primary Air Control by pull- follow these operating procedures: ing out making sure to maintain flames in the insert. Start-Up 1. Regardless of desired heat output, when loading insert, Air is closed. It is very important to maintain flames in your burn your Quadra-Fire with both air controls wide open for insert during the first few ho
Resumen del contenido incluido en la página 18
R 2700-I WOOD INSERT (ACT) AIR qUALITY AND YOUR START-Up AIR SYSTEM qUADRA-FIRE INSERT The combustion air enters at the rear of the firebox through In recent years there has been an increasing concern about the rear air tubes. This air supply is controlled by the Start- the quality of our air. Much of the blame for poor air quality Up Air Control. has been placed on the burning of wood for home heating. pRIMARY AIR SYSTEM In order to improve this situation we at Quadra-Fire have d
Resumen del contenido incluido en la página 19
R 2700-I WOOD INSERT (ACT) MAINTENANCE CREOSOTE (CHIMNEy) CLEANING CLEANING pLATED SURFACES Remove all ash from the firebox and extinguish all hot embers IMpORTANT: You must clean all the fingerprints and oils before disposal. Allow the appliance to cool completely. from the plated surfaces before firing the insert for the first Disconnect flue pipe or remove baffle and ceramic blanket from time. Use warm soapy water and a soft rag, glass cleaner appliance before cleaning chimney. O
Resumen del contenido incluido en la página 20
R 2700-I WOOD INSERT (ACT) 6 BRICK REpLACEMENT INSTRUCTIONS The firebox of your Quadra-Fire 2700-I Insert is lined with high 6 2 1 1 quality firebrick which has exceptional insulating properties. 1 There is no need for a grate, simply build a fire on the firebrick 1 floor. 5 5 1 1. Be certain coals are completely cold. Remove all old brick 1 and ash from unit and vacuum out firebox. 4 1 4 1 2. Remove new brick set from box and lay out to diagram as 1 shown. 1 1 . Lay bottom bricks in
