Resumen del contenido incluido en la página 1
DO NOT
DISCARD
Owner’s Manual
Installation and Operation
Model:
Cyclone-BN
Cyclone-BC
CAUTION
DO NOT DISCARD THIS MANUAL
• Important operating • Read, understand and follow • Leave this manual with
and maintenance these instructions for safe
party responsible for use
instructions included. installation and operation.
and operation.
WARNING
WARNING: If the information in these
HOT SURFACES!
instructions is not followed exactly, a fi re
Glass and other surfaces are hot during
or explosion ma
Resumen del contenido incluido en la página 2
Read this manual before installing or operating this appliance. Please retain this owner’s manual for future reference. Congratulations Congratulations on selecting a Heat & Glo gas appliance This Owner’s Manual should be retained for future —an elegant and clean alternative to wood burning reference. We suggest that you keep it with your other important documents and product manuals. appliances. The Heat & Glo gas appliance you have selected is designed to provide the utmost in safety, The
Resumen del contenido incluido en la página 3
Table of Contents 1 Listing and Code Approvals 9 Gas Information A. Appliance Certifi cation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 A. Fuel Conversions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 B. Glass Specifi cations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 B. Gas Pressures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 C. BTU Specifi cations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 C. G
Resumen del contenido incluido en la página 4
Listing and Code Approvals 1 1 A. Appliance Certifi cation D. High Altitude Installations U.L. Listed gas appliances are tested and approved with- MODELS: Cyclone out requiring changes for elevations from 0 to 2000 feet in the U.S.A. and Canada. LABORATORY: Underwriters Laboratories, Inc. (UL) TYPE: Direct Vent Gas Fireplace When installing this appliance at an elevation above 2000 feet, it may be necessary to decrease the input rating STANDARD: ANSI Z21.50-2000 • CSA2.33-M98 • UL307B b
Resumen del contenido incluido en la página 5
Inspection Note: The following requirements reference various The state or local gas inspector of the side wall horizon- Massachusetts and national codes not contained in this tally vented gas fueled equipment shall not approve the document. installation unless, upon inspection, the inspector ob- serves carbon monoxide detectors and signage installed H. Requirements for the Commonwealth of in accordance with the provisions of 248 CMR 5.08(2)(a)1 Massachusetts through 4. For all side wall
Resumen del contenido incluido en la página 6
Getting Started 2 2 A. Design and Installation Considerations C. Inspect Appliance and Components Heat & Glo direct vent gas appliances are designed to operate with all combustion air siphoned from outside of WARNING the building and all exhaust gases expelled to the out- Inspect appliance and components for damage. side. No additional outside air source is required. Damaged parts may impair safe operation. • Do NOT install damaged components. • Do NOT install incomplete components. CAUTIO
Resumen del contenido incluido en la página 7
Framing and Clearances 3 3 Note: WARNING • Illustrations reflect typical installations and are FOR Fire Risk DESIGN PURPOSES ONLY. Provide adequate clearance: • Illustrations/diagrams are not drawn to scale. • Around air openings • Actual installation may vary due to individual design preference. • To combustibles • For service access A. Selecting Appliance Location Locate appliance away from traffi c areas. When selecting a location for your appliance it is important to Note: For actual
Resumen del contenido incluido en la página 8
B. Constructing the Appliance Chase D A chase is a vertical boxlike structure built to enclose the gas appliance and/or its vent system. Vertical vents that run on the outside of a building may be, but are not re- quired to be, installed inside a chase. Construction of the chase may vary with the type of build- A ing. These instructions are not substitutes for the require- ments of local building codes. Local building codes MUST be checked. Chases should be constructed in the manner of all o
Resumen del contenido incluido en la página 9
D. Mantel Projections Clearances to Mantels or other Combustibles above Appliance 12 IN. MIN. TO CEILING AND/OR MANTEL TOP OF UNIT Figure 3.3 Clearances to mantels or other combustibles above appliance Heat & Glo • Cyclone-BN, Cyclone-BC • 2073-900 Rev. N • 10/08 9
Resumen del contenido incluido en la página 10
Termination Locations 4 4 HORIZONTAL A. Vent Termination Minimum Clearances OVERHANG 2 FT. 2 FEET MIN. WARNING VERTICAL MIN. WALL LOWEST Fire Risk. DISCHARGE OPENING Explosion Risk. GAS DIRECT VENT TERMINATION CAP Maintain vent clearance to combustibles as specifi ed. X 12 • Do not pack air space with insulation or other materials. ROOF PITCH IS X/ 12 Failure to keep insulation or other materials away from vent pipe may cause fi re. H (MIN.) - MINIMUM HEIGHT FROM ROOF TO LOWEST DISCHARGE
Resumen del contenido incluido en la página 11
M N P R Q (See Note 2) V T S S Electrical V V Service D* V = VENT TERMINAL X V = AIR SUPPLY INLET = AREA WHERE TERMINAL IS NOT PERMITTED A = 12 inches.................clearances above grade, veranda, L** = 7 ft. ......................... clearance above paved (See Note 1) (See Note 1) porch, deck or balcony sidewalk or a paved driveway located on public property B = 12 inches.................clearances to window or door M*** = 18 inches................ clearance under veranda, porch, that
Resumen del contenido incluido en la página 12
Vent Information and Diagrams 5 5 A. Vent Table Key The abbreviations listed in this vent table key are used in the vent diagrams. Symbol Description Vertical First section (closest to appliance) of vertical length V1 Second section of vertical length V2 First section (closest to appliance) of horizontal length H1 8-1/2 in. Second section of horizontal length H2 WARNING Horizontal Fire Hazard. Explosion Risk. Figure 5.1 Asphyxiation Risk. Do NOT connect this gas appliance to a chimney fl ue
Resumen del contenido incluido en la página 13
D. Vent Diagrams WARNING Fire Risk. Explosion Risk. Do NOT pack insulation or other combustibles between ceiling fi restops. • ALWAYS maintain specifi ed clearances around venting and fi restop systems. • Install wall shield and ceiling fi restops as specifi ed. Failure to keep insulation or other material away from vent pipe may cause fi re. 1. Top Vent - Horizontal Termination V Min. H Max. T T One Elbow 1.5 ft. 2 ft. NOTE: There MUST be a 25% 2.5 ft. 5 ft. reduction in total H when using 3.5 ft
Resumen del contenido incluido en la página 14
1. Top Vent - Horizontal Termination - (continued) V H V H V Min. H Max. 1 1 2 2 T T Three Elbows 1.5 ft. 2 ft. **** **** 2.5 ft. 5 ft. NOTE: There MUST be a 25% reduction in total H when using 3.5 ft. 8 ft. fl ex vent except when using the simple up and out installation **** (see Figure 5.7). **** 4.5 ft. 11 ft. V + H = 40 ft. Max. T T *No specifi c restrictions on this value EXCEPT V + H cannot exceed 40 ft. Max. T T H 1 H 2 V 2 V 1 Figure 5.5 14 Heat & Glo • Cyclone-BN, Cyclone-BC • 2073
Resumen del contenido incluido en la página 15
2. Top Vent - Vertical Termination V MAX. CAP T No Elbow 40 ft. Note: Depending on the vent run an exhaust baffl e may be required to ensure best fl ame appearance. See Section 7.B for baffl e installa- tion instructions. V T Figure 5.6 Flex Vent TERMINATION CAP 3 in. CLEARANCE The fl ex vent must be supported with the spacing between support intervals not exceeding 4 feet, with no more than ½ inch sag between supports. A support is required at each change in venting direction, and in any loc
Resumen del contenido incluido en la página 16
2. Top Vent - Vertical Termination - (continued) V V V Min. H Max. 1 2 T T Two Elbows 1.5 ft. 2 ft. ** H T ** 2.5 ft. 5 ft. 3.5 ft. 8 ft. ** ** 4.5 ft. 11 ft. V + H = 40 ft. Max. T T *No specifi c restrictions on this value EXCEPT V + H cannot exceed 40 ft. Max. T T V 2 NOTE: There MUST be a 25% reduction in total H when using fl ex vent except when using the simple up and out installation (see Figure 5.7). V 1 V H H V V Min. H Max. 1 1 2 2 T T Three Elbows **** 1.5 ft. 2 ft. 2.5 ft. 5 ft. ***
Resumen del contenido incluido en la página 17
Vent Clearances and Framing 6 6 A. Pipe Clearances to Combustibles B. Wall Penetration Framing Combustible Wall Penetration WARNING Whenever a combustible wall is penetrated, you must frame a hole for the wall shield fi restop. The wall shield Fire Risk. fi restop maintains minimum clearances and prevents cold Explosion Risk. air infi ltration. Maintain vent clearance to combustibles as specifi ed. • The opening must be framed on all four sides using the same size framing materials as those
Resumen del contenido incluido en la página 18
C. Vertical Penetration Framing A ceiling fi restop MUST be used between fl oors and attics. • Frame opening 9 in. x 9 in. (229 mm x 229 mm) whenever the vent penetrates a ceiling/ fl oor (see Figure 6.3). • Frame the area with the same sized lumber as used in ceiling/fl oor joist. ATTIC ABOVE • The ceiling fi restop may be installed above or below the ceiling joists when installed with a attic insulation shield. It must be under joists between fl oors that are not insulated. Refer to Figure 6
Resumen del contenido incluido en la página 19
D. Install Attic Insulation Shield BEND ALL TABS INWARD 90° WARNING! Fire Risk. DO NOT allow loose materials or TO MAINTAIN CLEARANCE insulation to touch vent. Hearth & Home Technologies AND PREVENT INSULATION FROM FALLING INSIDE Inc. requires the use of an attic shield. The National Fuel Gas Code ANSI Z223.1 and NFPA 54 requires an attic shield constructed of 26 gauge minimum metal that extends at least 2 in. (51 mm) above insulation. Attic shields must meet specifi ed clearance and be se
Resumen del contenido incluido en la página 20
Appliance Preparation 7 7 A. Securing and Leveling the Appliance B. Installing Exhaust Baffl e This appliance is supplied with three different sized exhaust WARNING baffl es, found in the manual bag assembly. Depending on the vent run for the installation one of the exhaust baffl es Fire Risk. may be required. To install one of the baffl es for best fl ame • Prevent contact with sagging, loose insulation. appearance refer to the table below for exhaust baffl e • Do NOT install against combust