Resumen del contenido incluido en la página 1
Installation and Operating Instructions
08/18936/0 Issue 0
Wall Fire SP4
Model No: SP4
Dimensions
(millimetres)
Fig. 1
THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE.
Electrical
Important Safety Advice:
WARNING – THIS APPLIANCE MUST BE EARTHED
This heater must be used on an AC ~ supply only and the
When using electrical appliances, basic
voltage marked on the heater must correspond to the supply
precautions should be followed to reduce the risk
voltage.
of
Resumen del contenido incluido en la página 2
Installation a lift appliance Do not connect appliance until properly fixed to the wall above wall ledge fixing bracket and the Instruction leaflet is read fully. wall ensure ledge bracket at back of fire engages This model is designed to be permanently fixed to a wall at a wall bracket minimum height of 300mm. see detail ’1’ Detail ’1’ The wall bracket must be fitted horizontally and the cable wall bracket routed to the bottom right of the heater as in Fig 1. slide down over bracket, ensure b
Resumen del contenido incluido en la página 3
Manual Operation The Standby Switch (Switch 1) must be first turned ‘ON’ and the AUTO/MAN (Switch 2) switch set to ‘MANUAL’ to operate the manual controls - see Fig 6. Note : When the fire is put in Manual mode the first time the flame effect will come on indicated by the Bottom neon coming on for 3 seconds - see Fig 7. MAN AUTO ON OFF Manual Controls Fig. 6 Setting Operation Indication Flame Effect only Press the ‘ I ’ button (Switch 3) Top Neon Press the ‘ I ’ button again (Switch 3) Flame Eff
Resumen del contenido incluido en la página 4
Operating Instructions Remote Control Operation • Switching ON/OFF The heater can be switched on by pressing the enter or General buttons. The remote control consists of 5 control buttons and a LCD The heater can be switched off by moving the cursor to the display with a visible area of 40x40mm. OFF menu item. The maximum range of use for the remote control is 15metres. • Flame brightness Navigate the cursor to FLAME with the buttons. Press ----- to change the brightness of the fire effec
Resumen del contenido incluido en la página 5
10. An entered program can be checked, edited and deleted just by navigating again into the PROG menu and pressing the enter button. With the --- buttons the -- different program numbers can be selected. To delete one program number, press the button. The CP symbol (clear program) appears and by pressing the enter button the current program will be deleted. leaves the menu without deleting the program. Replacing the remote control The new remote control must be set up as follows: Press swit
Resumen del contenido incluido en la página 6
For access to the bottom bulbs, carefully slide the flexible ro- Lamp Replacement tisserie to one side ensuring that the rubber grommets are not lost (see Fig 11). WARNING – ALWAYS DISCONNECT FROM THE POWER SUPPLY BEFORE REMOVING LAMPS. The front surround will need to be removed in order to change lamps. Warning -The front surround is heavy and easily damaged !. The front surround is fixed with 4 spring loaded pins and is supported at the top by the chassis. To gain access to the lamps please ap
Resumen del contenido incluido en la página 7
To refit the surround back to the chassis: 1. Refit the rotisserie making sure that the rubber grom- mets are carefully pushed back into the slotted holes on the axial brackets (see Fig 11). 2. Place the surround on the chassis bracket and align the pins with the spring slots. Make sure the surround is the correct way up with the cut out for switches at the bottom (see Fig 10). 3. Push firmly at each corner of the surround where the pin is located until it clips back into position.
Resumen del contenido incluido en la página 8
Cleaning WARNING – ALWAYS DISCONNECT FROM THE POWER SUPPLY BEFORE CLEANING THE HEATER. For general cleaning use a soft clean duster – never use abrasive cleaners. The glass viewing screen should be cleaned carefully with a soft cloth. DO NOT use proprietary glass cleaners. After Sales Service Your appliance is guaranteed for one year from the date of purchase. We undertake to repair or exchange free of charge within this period, any part with the exception of a lamp found to be defective due to
