Resumen del contenido incluido en la página 1
SHERWOOD INDUSTRIES IS AN ENVIRONMENTALLY RESPONSIBLE COMPANY. THIS MANUAL IS PRINTED ON RECYCLED PAPER.
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
FOCUS
B Y : S H E R W O O D I N D U S T R I E S L T D
OWNER’S MANUAL
WHAT TO DO IF YOU SMELL GAS
• Open windows/extinguish any open
flame.
• Do not try to light any appliance.
• Do not touch any electrical switch or
use any phone in your building.
• Immediately call your gas supplier
from a neighbour’s phone. Follow the
gas supplier’s
Resumen del contenido incluido en la página 2
Safety Precautions FOR SAFE INSTALLATION AND OPERATION OF YOUR “ENVIRO” HEATER, PLEASE CAREFULLY READ THE FOLLOWING INFORMATION: • All ENVIRO gas-fired appliances must be installed • To prevent injury, do not allow anyone who is in accordance with their instructions. Carefully read all unfamiliar with the stove to operate it. the instructions in this manual first. Consult the building • To prevent injury, if the pilot or pilot and authority having jurisdiction to determine the need for burn
Resumen del contenido incluido en la página 3
Table of Contents Safety Precautions.....................................................................................................2 Table of Contents......................................................................................................3 Codes And Approvals.................................................................................................4 Specifications............................................................................................................
Resumen del contenido incluido en la página 4
Codes And Approvals DIRECT VENT: This type is identified by the suffix DV. This appliance draws all of its air for combustion from outside the dwelling, through a specially designed vent pipe system. This appliance has been tested and approved for installations from 0 feet to 4500 feet (1372 m) above sea level. BV: This Vented appliance draws all of its combustion air from the dwelling and must be vented using listed B or L vent. May also be vented through a conventional chimney using a chim
Resumen del contenido incluido en la página 5
Specifications WARNING: Operation of this heater when not connected to a properly installed and maintained venting system can result in carbon monoxide (CO) poisoning and possible death. DIMENSIONS: 5 3 0 / 1 6 " ( 7 7 c m ) 1 8" ( 45 . 7 c m ) 3 14 / 1 6 " 1 12 / 1 6 " ( 36 . 0cm ) ( 3 0 . 6 c m ) 15 1 8 / 16 " ( 4 8 . 1cm ) 42 " ( 1 0 6 . 7 3 3" 1 4 / 8 " ( 7. 6c m ) ( 36. 5 c m ) 7 27 / 8 " ( 7 0.8 c m ) 1 3 1⁄4 " 19 1⁄2 " ( 3 3. 7 cm ) (49 . 5 cm ) 13 31 / 16 " ( 80. 8 cm ) Figure 1: Focus
Resumen del contenido incluido en la página 6
L O I P T O L T P T H T P T H I P F F Operating Instructions For Your Safety, Read Safety Precautions And Lighting Instructions Before Operating WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY A FIRE OR EXPLOSION MAY RESULT, CAUSING PROPERTY DAMAGE, PERSONAL INJURY OF LOSS OF LIFE. LIGHTING INSTRUCTIONS: H o t w h i l e o p e r a t i n g . D o n o t t o u c h , s e v e r e b u r n s m a y r e s u l t . K e e p c h ild r e n , c l o t hi ng , C A U T I O N : f u r n i t u r e , g a s o
Resumen del contenido incluido en la página 7
Operating Instructions ADJUSTING VENTURI AIR SETTINGS: There is only one (1) venturi and one (1) air shutter to be adjusted. When installing the burner top, ensure that the venturi tube is engaged to the air shutter adjustment rod. Use this small venturi adjustment rod to achieve a proper and efficient flame, shown in Figure 5. Adjust rod until the flame pattern is similar to Figure #. M ove t he ro d l o cat e d b e hi nd th e Table 1: Venturi Setting. p i ez o i gn i t o r to i nc r eas e
Resumen del contenido incluido en la página 8
Maintenance And Service ROUTINE MAINTENANCE: At least once a year, run through the following procedures to ensure the system is clean and working properly. Check the burner to see if all the ports are clear and clean. Check the pilot to make sure it is not blocked by anything. The pilot flame should be blue with little or no yellow on the tips. Warning: Clearances must be sufficient to allow access for maintenance and service Warning: Failure to position the parts in accordance with this manua
Resumen del contenido incluido en la página 9
Maintenance And Service to prevent personal injury. When the glass door assembly is being transported, it must be wrapped in newsprint and tape and/or a strong plastic bag. Do not operate with the glass front removed, cracked or broken. Removal and replacement of the glass from the door must be done by a licensed or qualified service person. The glass must be purchased from an ENVIRO dealer. No substitute materials are allowed. MAINTAINING FASCIA AND SURROUND FINISHES: When a plated surround
Resumen del contenido incluido en la página 10
Maintenance And Service FUEL CONVERSION: TO BE INSTALLED BY A QUALIFIED SERVICE AGENCY ONLY Please read and understand these instructions before installing. Warning: This conversion kit shall be installed by a qualified service agency in accordance with the manufacturer’s instructions and all applicable codes and requirements of the authority having jurisdiction. If the information in these instructions is not followed exactly, a fire, explosion or production of carbon monoxide may result c
Resumen del contenido incluido en la página 11
Maintenance And Service 7. Convert the SIT gas valve: a) Remove the black protection cap from the HI/LO knob by hand shown in Figure 8. 5 b) Insert a /32” or 4 mm Allen wrench into the hexagonal key-way of the screw (see Figure 9), rotate it counter-clockwise until it is free and extract it. c) Check that the screw is clean and if necessary L o o s e n remove dirt. T i g h t e n d) Flip the screw (refer to Figure 10). e) Using the Allen wrench as shown in Figure 9, rotate the screw clockwis
Resumen del contenido incluido en la página 12
Initial Installation WARNING: Operation of this heater when not connected to a properly installed and maintained venting system can result in carbon monoxide (CO) poisoning and possible death. Warning: Failure to position the parts in accordance with this manual, or failure to use only parts specifically approved with this appliance may result in property damage or personal injury. CLEARANCES TO COMBUSTIBLES: Mantle pillar to glass door 9” (22.8 cm) From floor to 8” wide mantle 38” (96.5
Resumen del contenido incluido en la página 13
Initial Installation QUALIFIED INSTALLERS ONLY DIRECT VENT MODEL: WARNING: This appliance has been designed to draw room air for proper heat circulation from the sides of the unit. Blocking or modifying the louvers in any way can create hazardous situations. This model is vented with TWO (2) 3” aluminum or stainless steel flex vent leading into a co-linear to co- axial vent adaptor and using a Simpson Dura Vent vertical termination cap. The flue collars of this model will fit inside of stand
Resumen del contenido incluido en la página 14
Initial Installation 6. Install the leveling legs. Thread the two (2) 5” (13 cm) bolts and locknut up into the captive nuts at each end of the leveling leg bracket (refer to Figure 15). 7. Place the unit part way into the fireplace. Connect the fireplace insert’s flexible gas line to the household gas supply, using locally approved methods. Place the electric cable so it can be connected to the power supply. L e v e l i n g l e g s br a c k e t 8. As you push the unit into its final posi
Resumen del contenido incluido en la página 15
Initial Installation QUALIFIED INSTALLERS ONLY 10. Connect the wires from the unit to the ON/OFF/ THERMOSTAT switch and the FAN CONTROLLER (see INITIAL INSTALLATION - ELECTRICAL REQUIREMENTS). 11. Place the assembled surround panel around the stove, align the slots. Push back then down to engage the surround panel hooks with the slots in the fireplace. Install the decorative fascia or bay window options to the appliance by aligning the hooks and the slots in the fireplace as seen in the su
Resumen del contenido incluido en la página 16
Initial Installation QUALIFIED INSTALLERS ONLY CONVERTING A DIRECT VENT FIREPLACE TO A B-VENTED FIREPLACE: Parts required for conversion 1 - 300°F (149°C) manual reset spill switch 3 0 0 ° F ( 1 4 0 ° F ) and wires S p i l l S w i tc h 1 - Drafthood (4’’ chimney connection) 2 - Air channels 1 - Drafthood diverter 1. Remove the chimney connector, fresh air cover plates and draft hood cover plate. 2. Install the 300°F (149°C) spill switch in the location provided. Ch i m ne y 3. Install the two
Resumen del contenido incluido en la página 17
Initial Installation QUALIFIED INSTALLERS ONLY VENTING FIREPLACE INSERTS: The ENVIRO FOCUS may be installed and vented into any solid fuel fireplace that has been installed in accordance with the National, Provincial/State and local building codes and has been constructed of non-combustible materials. An approved chimney liner and rain cap must be used. A throat connector or flashing must be installed to ensure a tight seal, top performance, safety and efficiency. Carefully follow the manufac
Resumen del contenido incluido en la página 18
Initial Installation QUALIFIED INSTALLERS ONLY ELECTRICAL REQUIREMENTS: The Focus will operate without electrical power. This model has a Millivolt gas control which uses the pilot flame to generate enough electricity to operate the main burners. This appliance when equipped with a blower, must be electrically connected and grounded in accordance with local codes or in the absence of local codes, with the current CSA C22.1 CANADIAN ELECTRICAL CODE Part 1, SAFETY STANDARDS FOR ELECTRICA
Resumen del contenido incluido en la página 19
L O I P T O L T P T H T P T H I P F F Initial Installation QUALIFIED INSTALLERS ONLY GAS LINE CONNECTION: Warning: Only persons licensed to work with gas piping may make the necessary gas connections to this appliance. Gas Line Connection: •This fireplace is equipped with a certified flexible pipe located on the right side of the unit, terminating in a 3⁄8” male NPT fitting. Consult the local authorities for local codes or use the CAN/CGA B149 (1 or 2) installation code in Canada. In the US,
Resumen del contenido incluido en la página 20
Secondary Installation LOG SET AND EMBER INSTALLATION: The placement of the logs is not arbitrary. If they are positioned incorrectly, the flames can be “pinched” and will not burn correctly. The burner comes with placement pins and rest areas, which make alignment easier. Using Figures 27 to 31, carefully set the logs in place. B a c k P l a c e m e n t / S u p p o r t P i n s NOTE: The logs are fragile and should be handled with care. Place the rear log on the two back placement pins. I
