Resumen del contenido incluido en la página 1
Resumen del contenido incluido en la página 2
TABLE OF CONTENTS SECTION PAGE Important Safety Information .................................................................................................3 Safety Information for Users of LP Gas .................................................................................4 Introduction ............................................................................................................................5 Specifications ..................................................................
Resumen del contenido incluido en la página 3
IMPORTANT SAFETY INFORMATION • An unvented room heater having an input rating of • During manufacturing, fabricating and shipping, various more than 6,000 Btu per hour shall not be installed in a components of this appliance are treated with certain bathroom oils, films or bonding agents. These bonding agents are not harmful but may produce annoying smoke and • An unvented room heater having an input rating of more smells as they are burned off during initial operation of than 10,000 Btu pe
Resumen del contenido incluido en la página 4
SAFETY INFORMATION FOR USERS OF LP-GAS Propane (LP-Gas) is a flammable gas which can cause fires by point with the members of your household. Someday when and explosions. In its natural state, propane is odorless and there may not be a minute to lose, everyone's safety will depend colorless. You may not know all the following safety precau- on knowing exactly what to do. If, after reading the following tions which can protect both you and your family from an information, you feel you still need
Resumen del contenido incluido en la página 5
INTRODUCTION Instructions to Installer 1. Installer must leave instruction manual with owner after smoke will occur. To prevent triggering of smoke alarms, ventilate installation. the room in which the unit is installed. 2. Installer must have owner fill out and mail warranty card supplied Installation on Rugs and Tile with unvented room heater. If this appliance is installed directly on carpeting, tile or other 3. Installer should show owner how to start and operate unvented combustible ma
Resumen del contenido incluido en la página 6
SPECIFICATIONS Model VFP32FP VFP36FP Input Maximum 32,000 36,000 Minimum 22,000 25,000 Minimum Firebox Opening Height without standoff 32 3/4" 34 3/4" Width 34” 39” Depth 17 3/8" 17 3/8” Gas Inlet 3/8” 3/8” Accessories EK-1 Embers Kit PE-20 Platinum Embers FBB4* Variable Speed Automatic Blower VPP32A VFP32FP — Ceramic Aged Brick Liner VPP36A VFP36FP — Ceramic Aged Brick Liner Accessories For VFP(32,36)FP(30,31) Only FRBC Battery Operated Remote Control FRBTC Battery Operated Remote Control w/
Resumen del contenido incluido en la página 7
Resumen del contenido incluido en la página 8
PROVISIONS FOR ADEQUATE COMBUSTION & VENTILATION AIR (continued) Ventilation Air From Outdoors (Figure 2) The space in the above example is a confined space because the Provide extra fresh air by using ventilation grills or ducts. You must actual BTU/Hr used is more than the maximum BTU/HR the space provide two permanent openings: one within 12" of the ceiling can support. You must provide additional fresh air. Your options and one with 12" of the floor. Connect these items directly to the a
Resumen del contenido incluido en la página 9
Resumen del contenido incluido en la página 10
GAS SUPPLY (continued) Checking Manifold Pressure VFP(32,36)FP(20,21)LP (Propane gas) will have a manifold VFP(32,36)FP(30,31)LN (Natural gas) will have a manifold pressure approximately 10.0"w.c. (2.49kPa) at the pressure pressure of approximately 3.5" w.c. (.871kPa) for maximum input or regulator outlet with the inlet pressure to the pressure regulator 1.7" w.c. (.423kPa) for minimum input at the pressure regulator outlet from a minimum of 11.0"w.c. (2.739kPa) for the purpose of input
Resumen del contenido incluido en la página 11
Resumen del contenido incluido en la página 12
Resumen del contenido incluido en la página 13
INSTALLING HOOD AND TRIM KIT A black hood and trim kit is furnished with each model Finishing VFP(32,36)FP fireplace. The hood MUST be installed before the All joints (top, bottom and sides), where the wall or decorative fireplace is used. Failure to do so may create a possible fire hazard. facing material meets the fireplace surround must be completely Attention: The hood is located behind top louver during shipment sealed with a non-combustible material. of fireplace. Remove top louver for acces
Resumen del contenido incluido en la página 14
Resumen del contenido incluido en la página 15
PLACEMENT OF GLOWING EMBERS AND LAVA ROCK Placement of the glowing embers (rock wool) is very individual Refer to Log Instruction Manual to order loose material (rock and light coverage of the areas indicated will provide your best wool). effects. We recommend separation of the rock wool by hand and Placing Lava Rock in Front of Burner on Fireplace Floor make your coverage as light and fluffy as possible. Spread lava rocks on fireplace floor in front of the burner pan. Place just enough embers o
Resumen del contenido incluido en la página 16
OPERATION INSTRUCTIONS/FLAME APPEARANCE PERIODIC CLEANING – Refer to parts diagram for location Flames from the pilot (rear right back side of the pan burner) as of items discussed below. well as the main flame should be visually checked as the log set • Do not use cleaning fluid to clean logs or any part of heater. is installed. • Logs - brush with soft bristle brush or vacuum with brush In normal operation at full rate after 10 to 15 minutes, the flame attachment. appearance should be sets o
Resumen del contenido incluido en la página 17
Resumen del contenido incluido en la página 18
Resumen del contenido incluido en la página 19
Resumen del contenido incluido en la página 20
Cleaning and Pilot Maintenance Oxygen Depletion Sensor Pilot (Figure 17) When the pilot has a large yellow tip flame, clean the Oxygen Depletion Sensor as follows: 1. Clean the ODS pilot by loosening nut B from the pilot tubing. When this procedure is required, grasp nut A with an open end wrench. 2. Blow air pressure through the holes indicated by the arrows. Figure 17 This will blow out foreign materials such as dust, lint and spider webs. Tighten nut B also by grasping nut A. Warning:
